mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
9c500db896
The factory partition of the Phicomm K2P contains two MAC addresses. The lower MAC address is at offset 0xe006 and the higher one is at offset 0xe000. Use the lower MAC address as base mac-address which the switch driver increments by one for the second (wan) vlan. The MAC addresses are still inverted in contrast to the stock firmware where the lower MAC address is used for wan. But at least the use of a MAC address not intended/reserved for this particular board is fixed. Signed-off-by: Jiawei Wang <me@jwang.link>
120 lines
1.8 KiB
Plaintext
120 lines
1.8 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "phicomm,k2p", "mediatek,mt7621-soc";
|
|
model = "Phicomm K2P";
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
stat_r {
|
|
label = "k2p:red:status";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
stat_y {
|
|
label = "k2p:yellow:status";
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
stat_b {
|
|
label = "k2p:blue:status";
|
|
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "permanent_config";
|
|
reg = <0x50000 0x50000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@a0000 {
|
|
label = "firmware";
|
|
reg = <0xa0000 0xf60000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
pcie0 {
|
|
mt76@0,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
device_type = "pci";
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0xe006>;
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "i2c", "jtag";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|