openwrt/target/linux/ath79/image/generic-ubnt.mk
Russell Senior d5812478ad ath79: add support for ubnt_bullet-m-ar7240 variant
This adds support for the Ubiquiti Bullet M (AR7240).

Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.

  Attention: airOS firmware versions >= 5.6 have a new bootloader with
  an incompatible partition table!

  Please downgrade to <= 5.5 _before_ flashing OpenWrt!
  Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other Ubiquiti M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin

The "fixed-link" section of the device tree is needed to avoid errors like this:

  Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?

With "fixed-link", the errors go away and eth0 comes up reliably.

Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:22:21 +01:00

329 lines
8.3 KiB
Makefile

DEVICE_VARS += UBNT_BOARD UBNT_CHIP UBNT_TYPE UBNT_VERSION UBNT_REVISION
# On M (XW) devices the U-Boot as of version 1.1.4-s1039 doesn't like
# VERSION_DIST being on the place of major(?) version number, so we need to
# use some number.
UBNT_REVISION := $(VERSION_DIST)-$(REVISION)
# mkubntimage is using the kernel image direct
# routerboard creates partitions out of the ubnt header
define Build/mkubntimage
-$(STAGING_DIR_HOST)/bin/mkfwimage -B $(UBNT_BOARD) \
-v $(UBNT_TYPE).$(UBNT_CHIP).v6.0.0-$(VERSION_DIST)-$(REVISION) \
-k $(IMAGE_KERNEL) -r $@ -o $@
endef
# all UBNT XM/WA devices expect the kernel image to have 1024k while flash, when
# booting the image, the size doesn't matter.
define Build/mkubntimage-split
-[ -f $@ ] && ( \
dd if=$@ of=$@.old1 bs=1024k count=1; \
dd if=$@ of=$@.old2 bs=1024k skip=1; \
$(STAGING_DIR_HOST)/bin/mkfwimage -B $(UBNT_BOARD) \
-v $(UBNT_TYPE).$(UBNT_CHIP).v$(UBNT_VERSION)-$(UBNT_REVISION) \
-k $@.old1 -r $@.old2 -o $@; \
rm $@.old1 $@.old2 )
endef
# UBNT_BOARD e.g. one of (XS2, XS5, RS, XM)
# UBNT_TYPE e.g. one of (BZ, XM, XW)
# UBNT_CHIP e.g. one of (ar7240, ar933x, ar934x)
# UBNT_VERSION e.g. one of (6.0.0, 8.5.0)
define Device/ubnt
DEVICE_VENDOR := Ubiquiti
DEVICE_PACKAGES := kmod-usb2
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | mkubntimage-split
endef
define Device/ubnt-bz
$(Device/ubnt)
SOC := ar7241
IMAGE_SIZE := 7448k
UBNT_BOARD := XM
UBNT_CHIP := ar7240
UBNT_TYPE := BZ
UBNT_VERSION := 6.0.0
endef
define Device/ubnt-sw
$(Device/ubnt)
SOC := ar7242
DEVICE_PACKAGES += kmod-usb-ohci
IMAGE_SIZE := 7552k
UBNT_BOARD := SW
UBNT_CHIP := ar7240
UBNT_TYPE := SW
UBNT_VERSION := 1.4.1
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
endef
define Device/ubnt-wa
$(Device/ubnt)
SOC := ar9342
IMAGE_SIZE := 15744k
UBNT_BOARD := WA
UBNT_CHIP := ar934x
UBNT_TYPE := WA
UBNT_VERSION := 8.5.0
endef
define Device/ubnt-xm
$(Device/ubnt)
DEVICE_VARIANT := XM
DEVICE_PACKAGES += kmod-usb-ohci
IMAGE_SIZE := 7448k
UBNT_BOARD := XM
UBNT_CHIP := ar7240
UBNT_TYPE := XM
UBNT_VERSION := 6.0.0
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
endef
define Device/ubnt-xw
$(Device/ubnt)
SOC := ar9342
DEVICE_VARIANT := XW
IMAGE_SIZE := 7552k
UBNT_BOARD := XM
UBNT_CHIP := ar934x
UBNT_REVISION := 42.$(UBNT_REVISION)
UBNT_TYPE := XW
UBNT_VERSION := 6.0.4
endef
define Device/ubnt_acb-isp
$(Device/ubnt)
SOC := qca9533
DEVICE_MODEL := airCube ISP
IMAGE_SIZE := 15744k
UBNT_BOARD := ACB-ISP
UBNT_CHIP := qca9533
UBNT_TYPE := ACB
UBNT_VERSION := 2.5.0
endef
TARGET_DEVICES += ubnt_acb-isp
define Device/ubnt_airrouter
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := AirRouter
SUPPORTED_DEVICES += airrouter
endef
TARGET_DEVICES += ubnt_airrouter
define Device/ubnt_bullet-m-ar7240
$(Device/ubnt-xm)
SOC := ar7240
DEVICE_MODEL := Bullet-M
DEVICE_VARIANT := XM (AR7240)
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_bullet-m-ar7240
define Device/ubnt_bullet-m-ar7241
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := Bullet-M
DEVICE_VARIANT := XM (AR7241)
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m ubnt,bullet-m
endef
TARGET_DEVICES += ubnt_bullet-m-ar7241
define Device/ubnt_bullet-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Bullet-M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m-xw
endef
TARGET_DEVICES += ubnt_bullet-m-xw
define Device/ubnt_edgeswitch-5xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 5XP
endef
TARGET_DEVICES += ubnt_edgeswitch-5xp
define Device/ubnt_edgeswitch-8xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 8XP
DEVICE_PACKAGES += switch-bcm53xx-mdio
endef
TARGET_DEVICES += ubnt_edgeswitch-8xp
define Device/ubnt_lap-120
$(Device/ubnt-wa)
DEVICE_MODEL := LiteAP ac
DEVICE_VARIANT := LAP-120
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_lap-120
define Device/ubnt_litebeam-ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := LiteBeam AC
DEVICE_VARIANT := Gen2
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_litebeam-ac-gen2
define Device/ubnt_nanobeam-ac
$(Device/ubnt-wa)
DEVICE_MODEL := NanoBeam AC
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_nanobeam-ac
define Device/ubnt_nanostation-ac
$(Device/ubnt-wa)
DEVICE_MODEL := Nanostation AC
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_nanostation-ac
define Device/ubnt_nanostation-ac-loco
$(Device/ubnt-wa)
DEVICE_MODEL := Nanostation AC loco
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_nanostation-ac-loco
define Device/ubnt_nanostation-loco-m
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_nanostation-loco-m
define Device/ubnt_nanostation-loco-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-loco-m-xw
define Device/ubnt_nanostation-m
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := Nanostation M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += nanostation-m
endef
TARGET_DEVICES += ubnt_nanostation-m
define Device/ubnt_nanostation-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += nanostation-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-m-xw
define Device/ubnt_picostation-m
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := Picostation M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_picostation-m
define Device/ubnt_rocket-m
$(Device/ubnt-xm)
SOC := ar7241
DEVICE_MODEL := Rocket-M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += rocket-m
endef
TARGET_DEVICES += ubnt_rocket-m
define Device/ubnt_routerstation_common
DEVICE_PACKAGES := -kmod-ath9k -wpad-mini -uboot-envtools kmod-usb-ohci \
kmod-usb2 fconfig
DEVICE_VENDOR := Ubiquiti
SOC := ar7161
IMAGE_SIZE := 16128k
IMAGES := factory.bin
IMAGE/factory.bin := append-rootfs | pad-rootfs | mkubntimage | \
check-size $$$$(IMAGE_SIZE)
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
endef
define Device/ubnt_routerstation
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation
UBNT_BOARD := RS
UBNT_TYPE := RSx
UBNT_CHIP := ar7100
DEVICE_PACKAGES += -swconfig
SUPPORTED_DEVICES += routerstation
endef
TARGET_DEVICES += ubnt_routerstation
define Device/ubnt_routerstation-pro
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation Pro
UBNT_BOARD := RSPRO
UBNT_TYPE := RSPRO
UBNT_CHIP := ar7100pro
SUPPORTED_DEVICES += routerstation-pro
endef
TARGET_DEVICES += ubnt_routerstation-pro
define Device/ubnt_unifi
$(Device/ubnt-bz)
DEVICE_MODEL := UniFi
SUPPORTED_DEVICES += unifi
endef
TARGET_DEVICES += ubnt_unifi
define Device/ubnt_unifiac
DEVICE_VENDOR := Ubiquiti
SOC := qca9563
IMAGE_SIZE := 7744k
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
define Device/ubnt_unifiac-lite
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-Lite
SUPPORTED_DEVICES += unifiac-lite
endef
TARGET_DEVICES += ubnt_unifiac-lite
define Device/ubnt_unifiac-lr
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-LR
SUPPORTED_DEVICES += unifiac-lite ubnt,unifiac-lite
endef
TARGET_DEVICES += ubnt_unifiac-lr
define Device/ubnt_unifiac-mesh
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-Mesh
SUPPORTED_DEVICES += unifiac-lite
endef
TARGET_DEVICES += ubnt_unifiac-mesh
define Device/ubnt_unifiac-mesh-pro
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-Mesh Pro
SUPPORTED_DEVICES += unifiac-pro
endef
TARGET_DEVICES += ubnt_unifiac-mesh-pro
define Device/ubnt_unifiac-pro
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-Pro
DEVICE_PACKAGES += kmod-usb2
SUPPORTED_DEVICES += unifiac-pro
endef
TARGET_DEVICES += ubnt_unifiac-pro