mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 09:39:00 +00:00
de768829a5
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
35 lines
683 B
Plaintext
35 lines
683 B
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621_dlink_dir-xx60-a1.dtsi"
|
|
|
|
/ {
|
|
compatible = "dlink,dir-2640-a1", "mediatek,mt7621-soc";
|
|
model = "D-Link DIR-2640 A1";
|
|
};
|
|
|
|
&leds {
|
|
usb2_white {
|
|
label = "white:usb2";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
trigger-sources = <&ehci_port2>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
|
|
usb3_white {
|
|
label = "white:usb3";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
trigger-sources = <&xhci_ehci_port1>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
};
|
|
|
|
&wifi0 {
|
|
mtd-mac-address = <&factory 0xe000>;
|
|
mtd-mac-address-increment = <1>;
|
|
};
|
|
|
|
&wifi1 {
|
|
mtd-mac-address = <&factory 0xe000>;
|
|
mtd-mac-address-increment = <2>;
|
|
};
|