mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 22:23:27 +00:00
c8a0166212
The following patch corrects a hard reset that occurs on alix and soekris net5501 hardware. Specifically, this is an issue with the via rhine NIC driver. Under periods of extreme load, the via rhine driver can cause a reset of the entire system. When this happens no output is seen on the console, the device simply reboots. This was reported in the following ticket: Consistent crash on Soekris NET5501 https://dev.openwrt.org/ticket/11882 I was able to reproduce the problem locally with numerous alix 2d13 platforms. Under heavy 64 byte frame size load from a Smartbits traffic generator, the alix hardware will hard reset in under 5 minutes. The same hardware, under the same load, on FreeBSD 9.0 does not reset. The patch below backports most of the via rhine changes from kernel 3.5. With OpenWrt trunk being on kernel 3.3.8, it seemed prudent to bring these changes in to avoid this serious issue. I've tested this heavily in my test environment and was able to keep the device stable under load for extended periods of time without any resets. Also, a nice side effect of this change is that it significantly raises the performance the platform. Without this patch the alix 2d13 can move approximately 29,000 packets per second at 64 byte frame sizes. After this patch the alix can move 52,000 packets per second at 64 byte frame sizes. I put this patch under the x86 patches as those are the only platforms with via rhine hardware that I'm aware of. If it needs to go some place else please let me know. Thanks, Adam Signed-off-by: Adam Gensler <openwrt@kristenandadam.net> SVN-Revision: 33072
61 lines
1.7 KiB
Diff
61 lines
1.7 KiB
Diff
--- a/drivers/net/ethernet/via/via-rhine.c
|
|
+++ b/drivers/net/ethernet/via/via-rhine.c
|
|
@@ -689,9 +689,12 @@ static void __devinit rhine_reload_eepro
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
static void rhine_poll(struct net_device *dev)
|
|
{
|
|
- disable_irq(dev->irq);
|
|
- rhine_interrupt(dev->irq, (void *)dev);
|
|
- enable_irq(dev->irq);
|
|
+ struct rhine_private *rp = netdev_priv(dev);
|
|
+ const int irq = rp->pdev->irq;
|
|
+
|
|
+ disable_irq(irq);
|
|
+ rhine_interrupt(irq, dev);
|
|
+ enable_irq(irq);
|
|
}
|
|
#endif
|
|
|
|
@@ -929,7 +932,6 @@ static int __devinit rhine_init_one(stru
|
|
dev = alloc_etherdev(sizeof(struct rhine_private));
|
|
if (!dev) {
|
|
rc = -ENOMEM;
|
|
- dev_err(&pdev->dev, "alloc_etherdev failed\n");
|
|
goto err_out;
|
|
}
|
|
SET_NETDEV_DEV(dev, &pdev->dev);
|
|
@@ -973,7 +975,6 @@ static int __devinit rhine_init_one(stru
|
|
}
|
|
#endif /* USE_MMIO */
|
|
|
|
- dev->base_addr = (unsigned long)ioaddr;
|
|
rp->base = ioaddr;
|
|
|
|
/* Get chip registers into a sane state */
|
|
@@ -996,8 +997,6 @@ static int __devinit rhine_init_one(stru
|
|
if (!phy_id)
|
|
phy_id = ioread8(ioaddr + 0x6C);
|
|
|
|
- dev->irq = pdev->irq;
|
|
-
|
|
spin_lock_init(&rp->lock);
|
|
mutex_init(&rp->task_lock);
|
|
INIT_WORK(&rp->reset_task, rhine_reset_task);
|
|
@@ -1158,7 +1157,6 @@ static void alloc_rbufs(struct net_devic
|
|
rp->rx_skbuff[i] = skb;
|
|
if (skb == NULL)
|
|
break;
|
|
- skb->dev = dev; /* Mark as being used by this device. */
|
|
|
|
rp->rx_skbuff_dma[i] =
|
|
pci_map_single(rp->pdev, skb->data, rp->rx_buf_sz,
|
|
@@ -1943,7 +1941,6 @@ static int rhine_rx(struct net_device *d
|
|
rp->rx_skbuff[entry] = skb;
|
|
if (skb == NULL)
|
|
break; /* Better luck next round. */
|
|
- skb->dev = dev; /* Mark as being used by this device. */
|
|
rp->rx_skbuff_dma[entry] =
|
|
pci_map_single(rp->pdev, skb->data,
|
|
rp->rx_buf_sz,
|
|
|