openwrt/target/linux/ath79/dts/qca9561_tplink_archer-c59-v1.dts
Shiji Yang 348e0ee157
ath79: convert ath10k pre-calibration data to NVMEM (binary MAC)
This patch converts ath10k pre-calibration data to NVMEM format for
wave 2 devices with mtd binary MAC address. The "pre-calibration"
NVMEM cell size is 0x2f20. The MAC addresses are assigned via dts.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-02-01 17:09:02 +01:00

124 lines
2.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca9561_tplink_archer-c5x.dtsi"
/ {
compatible = "tplink,archer-c59-v1", "qca,qca9560";
model = "TP-Link Archer C59 v1";
aliases {
label-mac-device = &eth1;
};
};
&leds {
usb {
label = "green:usb";
gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
linux,default-trigger = "usbport";
trigger-sources = <&hub_port0>;
};
};
&usb0 {
status = "okay";
};
&usb_phy0 {
status = "okay";
};
&pcie {
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&precal_art_5000>, <&macaddr_info_8 (-1)>;
nvmem-cell-names = "pre-calibration", "mac-address";
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x010000>;
read-only;
};
info: partition@10000 {
label = "info";
reg = <0x010000 0x010000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_info_8: macaddr@8 {
compatible = "mac-base";
reg = <0x8 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
partition@20000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x020000 0xe30000>;
};
partition@e50000 {
label = "tplink";
reg = <0xe50000 0x1a0000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
precal_art_5000: pre-calibration@5000 {
reg = <0x5000 0x2f20>;
};
};
};
};
};
};
&eth0 {
nvmem-cells = <&macaddr_info_8 1>;
nvmem-cell-names = "mac-address";
};
&eth1 {
nvmem-cells = <&macaddr_info_8 0>;
nvmem-cell-names = "mac-address";
};
&wmac {
mtd-cal-data = <&art 0x1000>;
nvmem-cells = <&macaddr_info_8 0>;
nvmem-cell-names = "mac-address";
};