openwrt/target/linux/ath79/dts/ar9344_enterasys_ws-ap3705i.dts
Adrian Schmutzler 1fb40a72da treewide: use more descriptive names for concatenated partitions
A few devices in ath79 and ramips use mtd-concat to concatenate
individual partitions into a bigger "firmware" or "ubi" partition.

However, the original partitions are still present and visible,
and one can write to them directly although this might break the
actual virtual, concatenated partition.

As we cannot do much about the former, let's at least choose more
descriptive names than just "firmwareX" in order to indicate the
concatenation to the user. He might be less tempted into overwriting
a "fwconcat1" than a "firmware1", which might be perceived as an
alternate firmware for dual boot etc.

This applies the new naming consistently for all relevant devices,
i.e. fwconcatX for virtual "firmware" members and ubiconcatX for
"ubi" members.

While at it, use DT labels and label property consistently, and
also use consistent zero-based indexing.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-27 20:33:45 +01:00

231 lines
3.6 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9344.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "enterasys,ws-ap3705i", "qca,ar9344";
model = "Enterasys WS-AP3705i";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &led_power_green;
led-failsafe = &led_power_red;
led-running = &led_power_green;
led-upgrade = &led_power_red;
label-mac-device = &eth0;
};
mtd-concat {
compatible = "mtd-concat";
devices = <&fwconcat0 &fwconcat1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x0 0x1dd0000>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&enable_gpio_11 &enable_gpio_16>;
led_power_green: power_green {
label = "green:power";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
led_power_red: power_red {
label = "red:power";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
lan_blue {
label = "blue:lan";
gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
};
lan_green {
label = "green:lan";
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
};
radio2 {
label = "green:radio2";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
ath9k-leds {
compatible = "gpio-leds";
radio1 {
label = "green:radio1";
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
};
};
&ref {
clock-frequency = <40000000>;
};
&uart {
status = "okay";
};
&pinmux {
enable_gpio_16: pinmux_enable_gpio_16 {
pinctrl-single,bits = <0x10 0x0 0x000000ff>;
};
enable_gpio_11: pinmux_enable_gpio_11 {
pinctrl-single,bits = <0x8 0x0 0xff000000>;
};
};
&wmac {
status = "okay";
qca,no-eeprom;
};
&spi {
status = "okay";
cs-gpios = <0>, <0>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot-bak";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "u-boot-env0";
reg = <0x80000 0x10000>;
read-only;
};
partition@90000 {
label = "u-boot-env1";
reg = <0x90000 0x10000>;
read-only;
};
partition@a0000 {
label = "u-boot";
reg = <0xa0000 0x80000>;
read-only;
};
partition@120000 {
label = "calibrate";
reg = <0x120000 0x10000>;
read-only;
};
partition@130000 {
label = "nvram";
reg = <0x130000 0x100000>;
read-only;
};
fwconcat0: partition@230000 {
label = "fwconcat0";
reg = <0x230000 0xdd0000>;
};
};
};
flash@1 {
compatible = "jedec,spi-nor";
reg = <1>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
fwconcat1: partition@0 {
label = "fwconcat1";
reg = <0x0 0x1000000>;
};
};
};
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
compatible = "pci168c,0033";
reg = <0x0000 0 0 0 0>;
qca,no-eeprom;
#gpio-cells = <2>;
gpio-controller;
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
};
};
&eth0 {
status = "okay";
pll-data = <0x1e000000 0x08000101 0x08001313>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
gmac-config {
device = <&gmac>;
rgmii-gmac0 = <1>;
rxd-delay = <0>;
rxdv-delay = <0>;
txen-delay = <0>;
txd-delay = <0>;
};
};