mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 23:42:43 +00:00
9ad3967f14
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
205 lines
4.9 KiB
Bash
205 lines
4.9 KiB
Bash
#!/bin/sh
|
|
|
|
# xor multiple hex values of the same length
|
|
xor() {
|
|
local val
|
|
local ret="0x$1"
|
|
local retlen=${#1}
|
|
|
|
shift
|
|
while [ -n "$1" ]; do
|
|
val="0x$1"
|
|
ret=$((ret ^ val))
|
|
shift
|
|
done
|
|
|
|
printf "%0${retlen}x" "$ret"
|
|
}
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_ubi_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local ubidev
|
|
local ubi
|
|
|
|
. /lib/upgrade/nand.sh
|
|
|
|
ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
ubi=$(nand_find_volume $ubidev $part)
|
|
[ -n "$ubi" ] || \
|
|
ath10kcal_die "no UBI volume found for $part"
|
|
|
|
dd if=/dev/$ubi of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath10kcal_die "failed to extract from $ubi"
|
|
}
|
|
|
|
ath10kcal_patch_mac_crc() {
|
|
local mac=$1
|
|
local mac_offset=6
|
|
local chksum_offset=2
|
|
local xor_mac
|
|
local xor_fw_mac
|
|
local xor_fw_chksum
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
|
|
|
|
xor_mac=${mac//:/}
|
|
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
|
|
|
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
|
|
|
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
|
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
|
}
|
|
|
|
ath10kcal_is_caldata_valid() {
|
|
local expected="$1"
|
|
|
|
magic=$(hexdump -v -n 2 -e '1/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
[[ "$magic" == "$expected" ]]
|
|
return $?
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 36864 2116
|
|
ath10kcal_is_caldata_valid "4408" || ath10kcal_extract "ART" 36864 2116
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
|
case "$board" in
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 36864 12064
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
openmesh,a62)
|
|
ath10kcal_extract "0:ART" 36864 12064
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a000000.wifi.bin")
|
|
case "$board" in
|
|
8dev,jalapeno |\
|
|
glinet,gl-b1300 |\
|
|
linksys,ea6350v3 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
;;
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 4096 12064
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
ath10kcal_ubi_extract "Factory" 4096 12064
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 4096 12064
|
|
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2)
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
|
|
;;
|
|
compex,wpj428 |\
|
|
engenius,eap1300 |\
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
ath10kcal_extract "0:ART" 4096 12064
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
ath10kcal_extract "ART" 4096 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-ahb-a800000.wifi.bin")
|
|
case "$board" in
|
|
8dev,jalapeno |\
|
|
glinet,gl-b1300 |\
|
|
linksys,ea6350v3 |\
|
|
qcom,ap-dk01.1-c1)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
;;
|
|
asus,map-ac2200)
|
|
ath10kcal_ubi_extract "Factory" 20480 12064
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
ath10kcal_ubi_extract "Factory" 20480 12064
|
|
;;
|
|
avm,fritzbox-4040)
|
|
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
|
|
;;
|
|
meraki,mr33)
|
|
ath10kcal_ubi_extract "ART" 20480 12064
|
|
ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3)
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
|
|
;;
|
|
compex,wpj428 |\
|
|
engenius,eap1300 |\
|
|
openmesh,a42 |\
|
|
openmesh,a62)
|
|
ath10kcal_extract "0:ART" 20480 12064
|
|
;;
|
|
zyxel,nbg6617 |\
|
|
zyxel,wre6606)
|
|
ath10kcal_extract "ART" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|