mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
02d53e6a21
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost the same as FB7330, but only one ETH-Port and no USB. Hardware SoC: Lantiq Xway ARX188 PSB 50812 EL RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5) Ethernet: Atheros 8030 Wireless: Atheros AR9227 b/g/n 2x2 DSL: Lantiq ADSL2+ DECT: Dialog SC14441 Buttons: WiFi, DECT LEDs: Power/DSL, Fon, DECT, WLAN, Info LEDs Power: GPIO#44 (active low) Internet: GPIO#47 (active low) DECT: GPIO#38 (active low) WLAN: GPIO#37 (active low) Info: GPIO#35 (active low) The Fon LED is labeled as internet in avm gpl sources. Buttons WLAN: GPIO#1 (active low) DECT: GPIO#2 (active low) Phy GPIO#03: 25 MHz GPIO#34: Reset (active low) GPIO#39: Int GPIO#42: MII MDIO GPIO#43: MII MDC PCIe GPIO#21: reset (active low) Installation: To install OpenWrt via Eva bootloader, within the first seconds after power on a ftp connection need to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1 ftp> quote REBOOT Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
52 lines
1.1 KiB
Plaintext
52 lines
1.1 KiB
Plaintext
CONFIG_ADM6996_PHY=y
|
|
CONFIG_AR8216_PHY=y
|
|
CONFIG_AT803X_PHY=y
|
|
CONFIG_BLK_MQ_PCI=y
|
|
CONFIG_CRC16=y
|
|
CONFIG_CRYPTO_ACOMP2=y
|
|
CONFIG_CRYPTO_DEFLATE=y
|
|
CONFIG_CRYPTO_LZO=y
|
|
CONFIG_FIRMWARE_IN_KERNEL=y
|
|
CONFIG_INPUT=y
|
|
CONFIG_INPUT_EVDEV=y
|
|
CONFIG_INPUT_POLLDEV=y
|
|
# CONFIG_ISDN is not set
|
|
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
|
|
CONFIG_LZO_COMPRESS=y
|
|
CONFIG_LZO_DECOMPRESS=y
|
|
CONFIG_MTD_NAND=y
|
|
CONFIG_MTD_NAND_ECC=y
|
|
CONFIG_MTD_NAND_PLATFORM=y
|
|
CONFIG_MTD_NAND_XWAY=y
|
|
# CONFIG_MTD_PHYSMAP_OF is not set
|
|
CONFIG_MTD_UBI=y
|
|
CONFIG_MTD_UBI_BEB_LIMIT=20
|
|
CONFIG_MTD_UBI_BLOCK=y
|
|
# CONFIG_MTD_UBI_FASTMAP is not set
|
|
# CONFIG_MTD_UBI_GLUEBI is not set
|
|
CONFIG_MTD_UBI_WL_THRESHOLD=4096
|
|
CONFIG_NLS=y
|
|
CONFIG_OF_ADDRESS_PCI=y
|
|
CONFIG_OF_PCI=y
|
|
CONFIG_OF_PCI_IRQ=y
|
|
CONFIG_PCI=y
|
|
# CONFIG_PCIE_LANTIQ is not set
|
|
CONFIG_PCI_DOMAINS=y
|
|
CONFIG_PCI_LANTIQ=y
|
|
CONFIG_REGULATOR=y
|
|
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
|
CONFIG_RTL8306_PHY=y
|
|
CONFIG_RTL8366S_PHY=y
|
|
CONFIG_RTL8367B_PHY=y
|
|
CONFIG_RTL8367_PHY=y
|
|
CONFIG_UBIFS_FS=y
|
|
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
|
|
CONFIG_UBIFS_FS_LZO=y
|
|
CONFIG_UBIFS_FS_ZLIB=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_COMMON=y
|
|
# CONFIG_USB_EHCI_HCD is not set
|
|
CONFIG_USB_SUPPORT=y
|
|
CONFIG_ZLIB_DEFLATE=y
|
|
CONFIG_ZLIB_INFLATE=y
|