mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-14 08:50:14 +00:00
0d23fd2ab2
>From the Documentation/devicetree/bindings/leds/common.txt: - default-state : The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no glitch should be produced where the LED momentarily turns off (or on). The "keep" setting will keep the LED at whatever its current state is, without producing a glitch. The default is off if this property is not present. So setting the default-state of the LEDs to `off` is redundant as `off` is default LED state anyway. We should remove it as almost every new PR/patch submission contains this property by default which seems to be just copy&paste from some DTS file already present in the tree. Signed-off-by: Petr Štetiar <ynezz@true.cz>
171 lines
2.6 KiB
Plaintext
171 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9557.dtsi"
|
|
|
|
/ {
|
|
compatible = "ocedo,koala", "qca,qca9557";
|
|
model = "OCEDO Koala";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &system;
|
|
led-failsafe = &system;
|
|
led-running = &system;
|
|
led-upgrade = &system;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "koala:green:power";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wifi2 {
|
|
label = "koala:yellow:wlan2";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wifi5 {
|
|
label = "koala:red:wlan58";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
system: system {
|
|
label = "koala:blue:sys";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
clocks = <&extosc>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x740000>;
|
|
};
|
|
|
|
partition@790000 {
|
|
label = "vendor";
|
|
reg = <0x790000 0x740000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@ed0000 {
|
|
label = "data";
|
|
reg = <0xed0000 0x110000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "id";
|
|
reg = <0xfe0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x06>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
phy-mode = "rgmii-rxid";
|
|
|
|
at803x-disable-smarteee;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x00>;
|
|
|
|
phy-handle = <&phy5>;
|
|
phy-mode = "rgmii-rxid";
|
|
|
|
pll-data = <0xae000000 0xa0000101 0xa0001313>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
rxdv-delay = <3>;
|
|
rxd-delay = <3>;
|
|
txen-delay = <0>;
|
|
txd-delay = <0>;
|
|
rgmii-enabled = <1>;
|
|
};
|
|
};
|