mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 09:39:00 +00:00
5897b2be21
The lines-initial-states property was an early attempt to set the latch bit of the shift register on driver probe. It is not implemented in the driver and was rejected upstream. The latch bit was always set by a GPIO hog, so this property is safe to drop. Signed-off-by: David Bauer <mail@david-bauer.net>
175 lines
2.8 KiB
Plaintext
175 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
compatible = "avm,fritz4020", "qca,qca9560";
|
|
model = "AVM FRITZ!Box 4020";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &info_red;
|
|
led-running = &power;
|
|
led-upgrade = &info_red;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "fritz4020:green:power";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "fritz4020:green:wlan";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "fritz4020:green:lan";
|
|
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "fritz4020:green:wan";
|
|
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
info {
|
|
label = "fritz4020:green:info";
|
|
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
info_red: info_red {
|
|
label = "fritz4020:red:info";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
wps_button {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan_button {
|
|
label = "WLAN button";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "urlader";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
compatible = "avm,eva-firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0xee0000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "tffs (1)";
|
|
reg = <0xf00000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "tffs (2)";
|
|
reg = <0xf80000 0x080000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-mode = "mii";
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|