openwrt/target/linux/ipq806x/files-4.9/arch/arm/boot/dts
Dongming Han 04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
..
qcom-ipq4019-a42.dts ipq806x: add support for OpenMesh A42 2018-01-13 08:00:14 +01:00
qcom-ipq4019-bus.dtsi ipq806x: add ipq4019 support 2017-03-22 09:45:18 +01:00
qcom-ipq4019-fritz4040.dts ipq806x: overhaul AVM FRITZ!box 4040 device-tree file 2018-01-18 21:21:11 +01:00
qcom-ipq4019-gl-b1300.dts ipq806x: add support for GL.iNet GL-B1300 2018-02-14 09:40:32 +01:00
qcom-ipq8064-ap148.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-c2600.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-d7800.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-db149.dts
qcom-ipq8064-ea8500.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-r7500.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-r7500v2.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064-vr2600v.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8064.dtsi ipq806x: usb: add phy 1 master reset control 2018-01-17 11:04:57 +01:00
qcom-ipq8065-nbg6817.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8065-r7800.dts ipq806x: force 2nd pci slot into gen1 mode 2018-01-17 11:02:05 +01:00
qcom-ipq8065-v1.0.dtsi
qcom-ipq8065.dtsi ipq8065: adjust SS USB PHY power settings 2018-01-17 11:05:11 +01:00