#include "mt7621.dtsi" #include #include / { compatible = "afoundry,ew1200", "mediatek,mt7621-soc"; model = "EW1200"; aliases { led-boot = &led_run; led-failsafe = &led_run; led-running = &led_run; led-upgrade = &led_run; }; keys { compatible = "gpio-keys"; reset { label = "reset"; gpios = <&gpio 18 GPIO_ACTIVE_LOW>; linux,code = ; }; }; leds { compatible = "gpio-leds"; led_run: run { label = "green:run"; gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; }; usb { label = "green:usb"; gpios = <&gpio 4 GPIO_ACTIVE_LOW>; trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; linux,default-trigger = "usbport"; }; }; }; &sdhci { status = "okay"; }; &spi0 { status = "okay"; flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <10000000>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "u-boot"; reg = <0x0 0x30000>; read-only; }; partition@30000 { label = "u-boot-env"; reg = <0x30000 0x10000>; read-only; }; factory: partition@40000 { label = "factory"; reg = <0x40000 0x10000>; read-only; nvmem-layout { compatible = "fixed-layout"; #address-cells = <1>; #size-cells = <1>; eeprom_factory_0: eeprom@0 { reg = <0x0 0x400>; }; eeprom_factory_8000: eeprom@8000 { reg = <0x8000 0x200>; }; macaddr_factory_e000: macaddr@e000 { reg = <0xe000 0x6>; }; }; }; partition@50000 { compatible = "denx,uimage"; label = "firmware"; reg = <0x50000 0xfb0000>; }; }; }; }; &pcie { status = "okay"; }; &pcie0 { wifi@0,0 { compatible = "mediatek,mt76"; reg = <0x0000 0 0 0 0>; nvmem-cells = <&eeprom_factory_8000>; nvmem-cell-names = "eeprom"; ieee80211-freq-limit = <5000000 6000000>; led { led-sources = <2>; led-active-low; }; }; }; &pcie1 { wifi@0,0 { compatible = "mediatek,mt76"; reg = <0x0000 0 0 0 0>; nvmem-cells = <&eeprom_factory_0>; nvmem-cell-names = "eeprom"; ieee80211-freq-limit = <2400000 2500000>; led { led-sources = <0>; led-active-low; }; }; }; &gmac0 { nvmem-cells = <&macaddr_factory_e000>; nvmem-cell-names = "mac-address"; }; &gmac1 { status = "okay"; label = "wan"; phy-handle = <ðphy4>; nvmem-cells = <&macaddr_factory_e000>; nvmem-cell-names = "mac-address"; mac-address-increment = <1>; }; &mdio { ethphy4: ethernet-phy@4 { reg = <4>; }; }; &switch0 { ports { port@0 { status = "okay"; label = "lan1"; }; port@1 { status = "okay"; label = "lan2"; }; port@2 { status = "okay"; label = "lan3"; }; port@3 { status = "okay"; label = "lan4"; }; }; }; &state_default { gpio { groups = "i2c", "uart3", "wdt"; function = "gpio"; }; };