--- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -44,6 +44,9 @@ config TARGET_NET2BIG_V2 config TARGET_NETSPACE_V2 bool "LaCie netspace_v2 Board" +config TARGET_NETGEAR_MS2110 + bool "Netgear MS2110 Board" + config TARGET_IB62X0 bool "ib62x0 Board" @@ -95,6 +98,7 @@ source "board/iomega/iconnect/Kconfig" source "board/keymile/Kconfig" source "board/LaCie/net2big_v2/Kconfig" source "board/LaCie/netspace_v2/Kconfig" +source "board/Marvell/netgear_ms2110/Kconfig" source "board/raidsonic/ib62x0/Kconfig" source "board/Seagate/dockstar/Kconfig" source "board/Seagate/goflexhome/Kconfig" --- /dev/null +++ b/board/Marvell/netgear_ms2110/Kconfig @@ -0,0 +1,12 @@ +if TARGET_NETGEAR_MS2110 + +config SYS_BOARD + default "netgear_ms2110" + +config SYS_VENDOR + default "Marvell" + +config SYS_CONFIG_NAME + default "netgear_ms2110" + +endif --- /dev/null +++ b/board/Marvell/netgear_ms2110/kwbimage.cfg @@ -0,0 +1,167 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x37543000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000833 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x00000099 # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 11, Cs0size=1Gb +# bit5-4: 00, Cs1width=x8 +# bit7-6: 11, Cs1size=1Gb +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000004 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 1, DDR ODT control lsd (disabled) +# bit5-3: 000, required +# bit6: 0, DDR ODT control msb, (disabled) +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 0 +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x03FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x0F, Size (i.e. 256MB) + +DATA 0xFFD01508 0x04000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x03FFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low) +# bit3-0: 2, ODT0Rd, MODT[0] asserted during read from DRAM CS1 +# bit7-4: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1 +# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E40F # CPU ODT Control +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 --- /dev/null +++ b/board/Marvell/netgear_ms2110/MAINTAINERS @@ -0,0 +1,6 @@ +NETGEAR_MS2110 BOARD +M: bodhi +S: Maintained +F: board/Marvell/netgear_ms2110 +F: include/configs/netgear_ms2110.h +F: configs/netgear_ms2110_defconfig --- /dev/null +++ b/board/Marvell/netgear_ms2110/Makefile @@ -0,0 +1,13 @@ +# +# (C) Copyright 2014 bodhi +# +# Based on +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := netgear_ms2110.o + --- /dev/null +++ b/board/Marvell/netgear_ms2110/netgear_ms2110.c @@ -0,0 +1,152 @@ +/* + * Copyright (C) 2014-2017 bodhi + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include "netgear_ms2110.h" +#include +#include + +DECLARE_GLOBAL_DATA_PTR; +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(NETGEAR_MS2110_OE_VAL_LOW, + NETGEAR_MS2110_OE_VAL_HIGH, + NETGEAR_MS2110_OE_LOW, NETGEAR_MS2110_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_SPI_SCn, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_SD_CLK, + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_SATA1_ACTn, + MPP21_SATA0_ACTn, + MPP22_GPIO, + MPP23_GPIO, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + MPP33_GE1_13, + MPP34_SATA1_ACTn, + MPP35_GPIO, + MPP36_GPIO, + MPP37_GPIO, + MPP38_GPIO, + MPP39_GPIO, + MPP40_GPIO, + MPP41_GPIO, + MPP42_GPIO, + MPP43_GPIO, + MPP44_GPIO, + MPP45_TDM_PCLK, + MPP46_TDM_FS, + MPP47_TDM_DRX, + MPP48_TDM_DTX, + MPP49_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ /* + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_NETGEAR_MS2110; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + return 0; +} +#ifdef CONFIG_RESET_PHY_R +/* Configure and enable MV88E1116 PHY */ +void reset_phy(void) +{ + u16 reg; + u16 devadr; + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { + printf("Err..%s could not read PHY dev address\n", + __FUNCTION__); + return; + } + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); + miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); + miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); + + /* reset the phy */ + miiphy_reset(name, devadr); + + printf("88E1116 Initialized on %s\n", name); +} +#endif /* CONFIG_RESET_PHY_R */ + --- /dev/null +++ b/board/Marvell/netgear_ms2110/netgear_ms2110.h @@ -0,0 +1,41 @@ +/* + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __NETGEAR_MS2110_H +#define __NETGEAR_MS2110_H + +#define NETGEAR_MS2110_OE_LOW (~(1 << 7)) +#define NETGEAR_MS2110_OE_HIGH (~(1 << 2 | 1 << 12)) +#define NETGEAR_MS2110_OE_VAL_LOW (0) +#define NETGEAR_MS2110_OE_VAL_HIGH (1 << 12) + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __NETGEAR_MS2110_H */ --- /dev/null +++ b/configs/netgear_ms2110_defconfig @@ -0,0 +1,50 @@ +CONFIG_ARM=y +CONFIG_KIRKWOOD=y +CONFIG_SYS_DCACHE_OFF=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_TARGET_NETGEAR_MS2110=y +CONFIG_IDENT_STRING="\nNetgear Stora MS2110" +CONFIG_SYS_PROMPT="Stora> " +CONFIG_HUSH_PARSER=y +CONFIG_SYS_TEXT_BASE=0x600000 +# CONFIG_DISPLAY_BOARDINFO is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_IDE=y +CONFIG_MVGBE=y +CONFIG_MII=y +CONFIG_SYS_NS16550=y +CONFIG_OF_LIBFDT=y +CONFIG_CMD_FDT=y +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_SETEXPR=y +CONFIG_CMD_DATE=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_JFFS2=y +CONFIG_CMD_USB=y +CONFIG_ISO_PARTITION=y +CONFIG_EFI_PARTITION=y +# CONFIG_MMC is not set +CONFIG_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000@0x0(uboot),0x20000@0xe0000(uboot_env),-@0x100000(ubi)" +CONFIG_CMD_MTDPARTS=y +CONFIG_CMD_NAND=y +CONFIG_ENV_IS_IN_NAND=y +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_ADDR=0xe0000 +CONFIG_ENV_OFFSET=0xe0000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_CMD_UBI=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_BLK=y +CONFIG_MVSATA_IDE=y +CONFIG_DM_RTC=y +CONFIG_RTC_MV=y --- /dev/null +++ b/include/configs/netgear_ms2110.h @@ -0,0 +1,155 @@ +/* + * (C) Copyright 2014-2017 bodhi + * (C) Copyright 2020 Zoltan HERPAI + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef _CONFIG_NGMS2110_H +#define _CONFIG_NGMS2110_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_MARVELL 1 +#define CONFIG_ARM926EJS 1 /* Basic Architecture */ +#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ +#define CONFIG_KIRKWOOD 1 /* SOC Family Name */ +#define CONFIG_KW88F6281 1 /* SOC Name */ +#define CONFIG_MACH_NETGEAR_MS2110 /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */ +#define CONFIG_CMD_ENV +#define CONFIG_PREBOOT +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* #define CONFIG_CMD_AUTOSCRIPT */ + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* Remove or override few declarations from mv-common.h */ +//#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */ +//#define CONFIG_SYS_PROMPT "Netgear Stora> " + +/* + * NAND configuration + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_KIRKWOOD +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ +#define NAND_ALLOW_ERASE_ALL 1 +#endif + +/* + * Default environment variables +*/ +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \ + "ubi part ubi; " \ + "ubifsmount ubi:rootfs; " \ + "ubi read 0x800000 kernel; " \ + "bootm 0x800000" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "arcNumber=2743\0" \ + "console=console=ttyS0,115200\0" \ + "ethact=egiga0\0" \ + "ethaddr=52:3b:20:9c:11:51\0" \ + "ipaddr=192.168.0.231\0" \ + "mtdids=nand0=orion_nand\0" \ + "mtdparts="CONFIG_MTDPARTS_DEFAULT "\0" \ + "serverip=192.168.0.220\0" \ + "bootargs_root=\0" + +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Other required minimal configurations + */ +#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* specify more that one ports available */ +#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable first port */ +#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE +#define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */ +#define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */ +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +#define CONFIG_PHY_BASE_ADR 0x0A +#define CONFIG_RESET_PHY_R /* use reset_phy() to init PHY */ +#endif /* CONFIG_CMD_NET */ + +/* + * USB/EHCI + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ +#define CONFIG_EHCI_IS_TDI +#define CONFIG_SUPPORT_VFAT +#endif /* CONFIG_CMD_USB */ + +/* + * File system + */ +#define CONFIG_JFFS2_NAND +#define CONFIG_JFFS2_LZO +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ + +/* + * SATA + */ + +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif + +/* + * Date Time + * */ +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_MV +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_DNS +#endif /* CONFIG_CMD_DATE */ + +#endif /* _CONFIG_NGMS2110_H */