#ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_ARM1136 #define CONFIG_OX820 #include /* get chip and board defs */ /* make cmd_ide.c quiet when compile */ #define __io /*#define CONFIG_ARCH_CPU_INIT*/ /*#define CONFIG_DISPLAY_CPUINFO*/ /*#define CONFIG_DISPLAY_BOARDINFO*/ /*#define CONFIG_BOARD_EARLY_INIT_F*/ /*#define CONFIG_SKIP_LOWLEVEL_INIT*/ /* mem */ #define CONFIG_SYS_SDRAM_BASE 0x60000000 #define CONFIG_NR_DRAM_BANKS 1 #define CONFIG_MIN_SDRAM_SIZE (128 * 1024 * 1024) /* 128 MB */ #define CONFIG_MAX_SDRAM_SIZE (512 * 1024 * 1024) /* 512 MB */ #define CONFIG_SRAM_BASE 0x50000000 #define CONFIG_SRAM_SIZE (64 * 1024) /* need do dma so better keep dcache off */ #define CONFIG_SYS_DCACHE_OFF /* clock */ #define CONFIG_PLLA_FREQ_MHZ 800 #define CONFIG_RPSCLK 6250000 #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_CLK_FREQ CONFIG_RPSCLK #define CONFIG_SYS_TIMERBASE TIMER1_BASE #define CONFIG_TIMER_PRESCALE TIMER_PRESCALE_16 /* serial */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_CLK CONFIG_RPSCLK #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_NS16550_COM1 UART_1_BASE #define CONFIG_CONS_INDEX 1 /* ide */ #define CONFIG_SYS_ATA_BASE_ADDR 0 #define CONFIG_SYS_ATA_DATA_OFFSET 0 #define CONFIG_SYS_ATA_REG_OFFSET 0 #define CONFIG_SYS_ATA_ALT_OFFSET 0 #define CONFIG_IDE_PLX #define CONFIG_SYS_IDE_MAXDEVICE 1 #define CONFIG_SYS_IDE_MAXBUS 1 #define CONFIG_IDE_PREINIT #define CONFIG_LBA48 /* nand */ #define CONFIG_NAND #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE STATIC_CS0_BASE #define NAND_CLE_ADDR_PIN 19 #define NAND_ALE_ADDR_PIN 18 #define MTDPARTS_DEFAULT "mtdparts=41000000.nand:" \ "14m(boot)," \ "-(ubi)" #define MTDIDS_DEFAULT "nand0=41000000.nand" #define UBIPART_DEFAULT "ubi" /* net */ #define CONFIG_DESIGNWARE_ETH #define CONFIG_DW_ALTDESCRIPTOR #define CONFIG_MII #define CONFIG_CMD_MII #define CONFIG_PHYLIB #define CONFIG_PHY_REALTEK /* spl */ #ifdef CONFIG_SPL_BUILD #define USE_DL_PREFIX /* rename malloc free etc, so we can override them */ #endif #if defined(CONFIG_BOOT_FROM_NAND) || defined(CONFIG_BOOT_FROM_SATA) #define CONFIG_SPL #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_TEXT_BASE 0x50000000 #define CONFIG_SPL_STACK (CONFIG_SRAM_BASE + (48 * 1024)) #define CONFIG_SPL_DISPLAY_PRINT #define CONFIG_SPL_BSS_DRAM_START 0x65000000 #define CONFIG_SPL_BSS_DRAM_SIZE 0x01000000 #define CONFIG_SPL_MALLOC_START 0x66000000 #endif #if defined(CONFIG_BOOT_FROM_NAND) #define CONFIG_SPL_NAND_SUPPORT #define BOOT_DEVICE_TYPE "NAND" #define BOOT_DEVICE_NAND 0xfeedbacc #define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_NAND #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 6 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \ 48, 49, 50, 51, 52, 53, 54, 55, \ 56, 57, 58, 59, 60, 61, 62, 63} #define CONFIG_SYS_NAND_PAGE_SIZE 2048 #define CONFIG_SYS_NAND_OOBSIZE 64 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 /* pages per erase block */ #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE) /* nand spl use 1 erase block, and use bit to byte encode for reliability */ #define CONFIG_SPL_MAX_SIZE (128 * 1024 / 8) #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000 /* spl kernel load is not enabled */ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 #define CONFIG_CMD_SPL_NAND_OFS 0 #define CONFIG_CMD_SPL_WRITE_SIZE 1024 #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) /* CONFIG_BOOT_FROM_NAND end */ #elif defined(CONFIG_BOOT_FROM_SATA) #define CONFIG_SPL_BLOCK_SUPPORT #define BOOT_DEVICE_TYPE "SATA" #define BOOT_DEVICE_BLOCK 860202 #define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_BLOCK #define CONFIG_SPL_MAX_SIZE (36 * 1024) #define CONFIG_SPL_LIBDISK_SUPPORT #define CONFIG_SPL_BLOCKDEV_INTERFACE "ide" #define CONFIG_SPL_BLOCKDEV_ID 0 #ifdef CONFIG_BOOT_FROM_FAT /* u-boot in fat partition */ #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_BLOCKDEV_FAT_BOOT_PARTITION 1 /* first partition */ #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" /* u-boot file name */ /* enable U-Boot Falcon Mode */ #define CONFIG_CMD_SPL #define CONFIG_SPL_OS_BOOT #define CONFIG_SPL_FAT_LOAD_ARGS_NAME "bootargs.bin" /* boot parameters */ #define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "falcon.img" /* kernel */ #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) #elif CONFIG_BOOT_FROM_EXT4 #define CONFIG_SPL_EXT4_SUPPORT #define CONFIG_BLOCKDEV_EXT4_BOOT_PARTITION 1 /* first partition */ #define CONFIG_SPL_EXT4_LOAD_PAYLOAD_NAME "/boot/u-boot.img" /* u-boot file name */ /* enable U-Boot Falcon Mode */ #define CONFIG_CMD_SPL #define CONFIG_SPL_OS_BOOT #define CONFIG_SPL_EXT4_LOAD_ARGS_NAME "/boot/bootargs.bin" /* boot parameters */ #define CONFIG_SPL_EXT4_LOAD_KERNEL_NAME "/boot/falcon.img" /* kernel */ #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) #else /* u-boot in raw sectors */ #define CONFIG_SYS_BLOCK_RAW_MODE_U_BOOT_SECTOR 1024 /* spl kernel load is not enabled */ #define CONFIG_SYS_BLOCK_RAW_MODE_KERNEL_SECTOR 4096 #define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTOR 0 #define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTORS (1024 / 512) #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100) #endif /* CONFIG_BOOT_FROM_FAT */ /* CONFIG_BOOT_FROM_SATA end */ #else /* generic, no spl support */ #endif /* boot */ #define CONFIG_IDENT_STRING " for OXNAS" #define CONFIG_MACH_TYPE MACH_TYPE_OXNAS #ifndef CONFIG_SPL_BUILD /* Enable devicetree support */ #define CONFIG_OF_LIBFDT #endif #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_CMDLINE_TAG #define CONFIG_INITRD_TAG #define CONFIG_BOOTDELAY 1 #define CONFIG_ZERO_BOOTDELAY_CHECK #define CONFIG_DEFAULT_CONSOLE_PARM "console=ttyS0,115200n8 earlyprintk=serial" /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* memtest works on */ #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE) #define CONFIG_SYS_AUTOLOAD "no" #define CONFIG_DEFAULT_CONSOLE CONFIG_DEFAULT_CONSOLE_PARM "\0" #define CONFIG_BOOTARGS CONFIG_DEFAULT_CONSOLE_PARM #define CONFIG_BOOTCOMMAND "run nandboot" #define CONFIG_BOOT_RETRY_TIME -1 #define CONFIG_RESET_TO_RETRY 60 #define CONFIG_NETCONSOLE #define CONFIG_IPADDR 192.168.50.100 #define CONFIG_SERVERIP 192.168.50.59 /* A sane default configuration... * When booting without a valid environment in ubi, first to loading and booting * the kernel image directly above U-Boot, maybe both were loaded there by * another bootloader. * Also use that same offset (0x90000) to load the rescue image later on (by * adding it onto the flash address where U-Boot is supposed to be stored by * the legacy loader, 0x440000, resulting in offset 0x4d0000 on the flash). * When coming up with a valid environment in ubi, first try to load the * kernel from a ubi volume kernel, if that fails, fallback to the rescue * image stored in boot partition. As a last resort try booting via * DHCP/TFTP. * In case there is no valid environment, first probe for a uimage in ram left * behind by the first bootloader on a tftp boot. * If that fails, switch to normal boot order and save environment. * The loader is supposed to be written to flash at offset 0x440000 and loaded to * RAM at 0x64000000 */ #define CONFIG_EXTRA_ENV_SETTINGS \ "load_kernel_ubi=ubi readvol 0x62000000 kernel;\0" \ "load_kernel_rescue=nand read 0x62000000 0x4e0000 0x400000;\0" \ "load_kernel_dhcp=dhcp 0x62000000 oxnas-rescue.bin;\0" \ "boot_kernel=bootm 0x62000000;\0" \ "boot_ubi=run load_kernel_ubi && run boot_kernel;\0" \ "boot_rescue=run load_kernel_rescue && run boot_kernel;\0" \ "boot_dhcp=run load_kernel_dhcp && run boot_kernel;\0" \ "normalboot=run boot_ubi; run boot_rescue; run boot_dhcp;\0" \ "firstboot=bootm 0x640a0000; setenv bootcmd run normalboot; " \ "setenv firstboot; saveenv; run bootcmd; \0" \ "bootcmd=run firstboot; \0" \ "console=" CONFIG_DEFAULT_CONSOLE \ "bootargs=" CONFIG_BOOTARGS "\0" \ "mtdids=" MTDIDS_DEFAULT "\0" \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ /* env */ #if defined(CONFIG_BOOT_FROM_NAND) #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_OFFSET 0x000C0000 #define CONFIG_ENV_SIZE 0x00020000 #define CONFIG_ENV_OFFSET_REDUND 0x00100000 #define CONFIG_ENV_SIZE_REDUND 0x00020000 #define CONFIG_ENV_RANGE (CONFIG_ENV_SIZE * 2) /* CONFIG_BOOT_FROM_NAND end */ #elif defined(CONFIG_BOOT_FROM_SATA) #ifdef CONFIG_BOOT_FROM_EXT4 #define CONFIG_ENV_IS_IN_EXT4 #define CONFIG_START_IDE #define EXT4_ENV_INTERFACE "ide" #define EXT4_ENV_DEVICE 0 #define EXT4_ENV_PART 1 #define EXT4_ENV_FILE "/boot/u-boot.env" #define CONFIG_ENV_SIZE (16 * 1024) #else #define CONFIG_ENV_IS_IN_FAT #define CONFIG_START_IDE #define FAT_ENV_INTERFACE "ide" #define FAT_ENV_DEVICE 0 #define FAT_ENV_PART 1 #define FAT_ENV_FILE "u-boot.env" #define CONFIG_ENV_SIZE (16 * 1024) #endif /* CONFIG_BOOT_FROM_SATA end */ #elif defined(CONFIG_BOOT_FROM_SATA) #else /* generic */ #define CONFIG_ENV_IS_IN_UBI 1 #define CONFIG_ENV_UBI_PART UBIPART_DEFAULT #define CONFIG_ENV_UBI_VOLUME "ubootenv" #define CONFIG_ENV_UBI_VOLUME_REDUND "ubootenv2" #define CONFIG_ENV_SIZE (16 * 1024) #endif /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_MONITOR_LEN (512 * 1024) #define CONFIG_SYS_TEXT_BASE 0x64000000 #define CONFIG_SYS_INIT_SP_ADDR 0x65000000 /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT "OX820 # " #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size*/ #define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ #define CONFIG_CMDLINE_EDITING #define CONFIG_AUTO_COMPLETE /* usb */ #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #define CONFIG_USB_EHCI #define CONFIG_EHCI_IS_TDI /* #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x3F */ #define CONFIG_USB_PLLB_CLK #define CONFIG_USB_EHCI_OXNAS #ifndef CONFIG_SPL_BUILD #define CONFIG_USB_STORAGE #endif #define CONFIG_CMD_USB /* cmds */ #define CONFIG_SYS_NO_FLASH #include #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_ASKENV #define CONFIG_CMD_GREPENV #define CONFIG_CMD_ENV_FLAGS #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP #define CONFIG_CMD_NFS #define CONFIG_CMD_PING #define CONFIG_CMD_PXE #define CONFIG_CMD_NAND #define CONFIG_CMD_MTDPARTS #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_IDE #define CONFIG_CMD_FAT #define CONFIG_FAT_WRITE #define CONFIG_CMD_EXT2 #define CONFIG_CMD_EXT4 #ifndef CONFIG_SPL_BUILD #define CONFIG_CMD_EXT4_WRITE #endif #define CONFIG_CMD_ZIP #define CONFIG_CMD_UNZIP #define CONFIG_CMD_TIME #define CONFIG_CMD_TERMINAL #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_MD5SUM #define CONFIG_CMD_HASH #define CONFIG_CMD_INI #define CONFIG_CMD_GETTIME #define CONFIG_CMD_BOOTMENU #define CONFIG_CMD_ELF #define CONFIG_DOS_PARTITION #define CONFIG_EFI_PARTITION /* for CONFIG_CMD_MTDPARTS */ #define CONFIG_MTD_DEVICE /* for CONFIG_CMD_UBI */ #define CONFIG_MTD_PARTITIONS /* for CONFIG_CMD_UBI */ #define CONFIG_RBTREE /* optional, for CONFIG_CMD_BOOTM & required by CONFIG_CMD_UBIFS */ #define CONFIG_LZO #define CONFIG_LZMA #define CONFIG_BZIP2 /* for CONFIG_CMD_ZIP */ #define CONFIG_GZIP_COMPRESSED /* for CONFIG_CMD_MD5SUM */ #define CONFIG_MD5 #define CONFIG_MD5SUM_VERIFY /* enable CONFIG_CMD_HASH's verification feature */ #define CONFIG_HASH_VERIFY #define CONFIG_REGEX /* for CONFIG_CMD_BOOTMENU & CONFIG_CMD_PXE */ #define CONFIG_MENU /* for new FIT uImage format generated in OpenWrt */ #define CONFIG_FIT #endif /* __CONFIG_H */