// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; #include "mt7981.dtsi" / { chosen { bootargs = "console=ttyS0,115200n8 root=PARTLABEL=rootfs rootwait"; }; aliases { label-mac-device = &gmac0; led-boot = &led_power; led-failsafe = &led_power; led-running = &led_power; led-upgrade = &led_power; }; reg_5v: regulator-5v { compatible = "regulator-fixed"; regulator-name = "fixed-5V"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-boot-on; regulator-always-on; }; fan_5v: regulator-fan-5v { compatible = "regulator-fixed"; regulator-name = "fan"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&pio 28 GPIO_ACTIVE_HIGH>; enable-active-high; }; gpio-keys { compatible = "gpio-keys"; reset { label = "reset"; linux,code = ; gpios = <&pio 1 GPIO_ACTIVE_LOW>; }; }; gpio-export { compatible = "gpio-export"; hub_power { gpio-export,name = "hub_power"; gpio-export,output = <1>; gpios = <&pio 5 GPIO_ACTIVE_HIGH>; }; 5G_power { gpio-export,name = "5G_power"; gpio-export,output = <1>; gpios = <&pio 11 GPIO_ACTIVE_HIGH>; }; 5G_control { gpio-export,name = "5G_control"; gpio-export,output = <1>; gpios = <&pio 9 GPIO_ACTIVE_HIGH>; }; 5G_reset { gpio-export,name = "5G_reset"; gpio-export,output = <0>; gpios = <&pio 10 GPIO_ACTIVE_HIGH>; }; }; leds { compatible = "gpio-leds"; wifi2g { label = "green:wifi2g"; gpios = <&pio 30 GPIO_ACTIVE_LOW>; }; wifi5g { label = "green:wifi5g"; gpios = <&pio 38 GPIO_ACTIVE_LOW>; }; 5g_led1 { label = "green:5g:led1"; gpios = <&pio 6 GPIO_ACTIVE_LOW>; }; 5g_led2 { label = "green:5g:led2"; gpios = <&pio 7 GPIO_ACTIVE_LOW>; }; 5g_led3 { label = "green:5g:led3"; gpios = <&pio 8 GPIO_ACTIVE_LOW>; }; 5g_led4 { label = "green:5g:led4"; gpios = <&pio 4 GPIO_ACTIVE_HIGH>; }; led_power: power { label = "green:power"; gpios = <&pio 39 GPIO_ACTIVE_LOW>; }; wan { label = "green:wan"; gpios = <&pio 31 GPIO_ACTIVE_LOW>; }; }; }; &uart0 { status = "okay"; }; &watchdog { status = "okay"; }; &mmc0 { pinctrl-names = "default", "state_uhs"; pinctrl-0 = <&mmc0_pins_default>; pinctrl-1 = <&mmc0_pins_uhs>; bus-width = <8>; max-frequency = <52000000>; cap-mmc-highspeed; vmmc-supply = <®_3p3v>; non-removable; status = "okay"; card@0 { compatible = "mmc-card"; reg = <0>; block { compatible = "block-device"; partitions { block-partition-env { partname = "u-boot-env"; nvmem-layout { compatible = "u-boot,env-layout"; }; }; block-partition-factory { partname = "factory"; nvmem-layout { compatible = "fixed-layout"; #address-cells = <1>; #size-cells = <1>; eeprom_factory_0: eeprom@0 { reg = <0x0 0x1000>; }; macaddr_factory_a: macaddr@a { compatible = "mac-base"; reg = <0xa 0x6>; #nvmem-cell-cells = <1>; }; }; }; }; }; }; }; &mdio_bus { reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; reset-delay-us = <600>; reset-post-delay-us = <20000>; phy5: ethernet-phy@5 { reg = <5>; compatible = "ethernet-phy-ieee802.3-c45"; }; }; ð { status = "okay"; gmac0: mac@0 { compatible = "mediatek,eth-mac"; reg = <0>; phy-mode = "2500base-x"; phy-handle = <&phy5>; nvmem-cells = <&macaddr_factory_a 0>; nvmem-cell-names = "mac-address"; }; gmac1: mac@1 { compatible = "mediatek,eth-mac"; reg = <1>; phy-mode = "gmii"; phy-handle = <&int_gbe_phy>; nvmem-cells = <&macaddr_factory_a 1>; nvmem-cell-names = "mac-address"; }; }; &pio { mmc0_pins_default: mmc0-pins-default { mux { function = "flash"; groups = "emmc_8"; }; }; mmc0_pins_uhs: mmc0-pins-uhs { mux { function = "flash"; groups = "emmc_8"; }; }; pcie_pins: pcie-pins { mux { function = "pcie"; groups = "pcie_pereset", "pcie_clk", "pcie_wake"; }; }; pwm0_pin: pwm0-pin-g0 { mux { function = "pwm"; groups = "pwm0_1"; }; }; }; &xhci { phys = <&u2port0 PHY_TYPE_USB2>; vbus-supply = <®_5v>; mediatek,u3p-dis-msk = <0x01>; status = "okay"; }; &usb_phy { status = "okay"; }; &pcie { pinctrl-names = "default"; pinctrl-0 = <&pcie_pins>; status = "okay"; }; &pwm { pinctrl-names = "default"; pinctrl-0 = <&pwm0_pin>; }; &wifi { nvmem-cells = <&eeprom_factory_0>; nvmem-cell-names = "eeprom"; status = "okay"; }; &fan { pwms = <&pwm 0 40000 0>; fan-supply = <&fan_5v>; interrupt-parent = <&pio>; interrupts = <29 IRQ_TYPE_EDGE_RISING>; status = "okay"; };