From 2c6e322a41c5e1ca45be50b9d5fbcda62dc23a0d Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 2 Jan 2023 10:46:28 +0100 Subject: [PATCH] arm64: dts: qcom: ipq6018: Sort nodes properly Order nodes by unit address if one exists and alphabetically otherwise. Signed-off-by: Konrad Dybcio Signed-off-by: Bjorn Andersson Link: https://lore.kernel.org/r/20230102094642.74254-4-konrad.dybcio@linaro.org --- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 562 +++++++++++++------------- 1 file changed, 281 insertions(+), 281 deletions(-) --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -87,6 +87,12 @@ }; }; + firmware { + scm { + compatible = "qcom,scm-ipq6018", "qcom,scm"; + }; + }; + cpu_opp_table: opp-table-cpu { compatible = "operating-points-v2"; opp-shared; @@ -123,12 +129,6 @@ }; }; - firmware { - scm { - compatible = "qcom,scm-ipq6018", "qcom,scm"; - }; - }; - pmuv8: pmu { compatible = "arm,cortex-a53-pmu"; interrupts = ; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + mboxes = <&apcs_glb 0>; + + rpm_requests: glink-channel { + compatible = "qcom,rpm-ipq6018"; + qcom,glink-channels = "rpm_requests"; + + regulators { + compatible = "qcom,rpm-mp5496-regulators"; + + ipq6018_s2: s2 { + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1062500>; + regulator-always-on; + }; + }; + }; + }; + smem { compatible = "qcom,smem"; memory-region = <&smem_region>; @@ -179,6 +201,102 @@ dma-ranges; compatible = "simple-bus"; + qusb_phy_1: qusb@59000 { + compatible = "qcom,ipq6018-qusb2-phy"; + reg = <0x0 0x00059000 0x0 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, + <&xo>; + clock-names = "cfg_ahb", "ref"; + + resets = <&gcc GCC_QUSB2_1_PHY_BCR>; + status = "disabled"; + }; + + ssphy_0: ssphy@78000 { + compatible = "qcom,ipq6018-qmp-usb3-phy"; + reg = <0x0 0x00078000 0x0 0x1c4>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_USB0_AUX_CLK>, + <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; + clock-names = "aux", "cfg_ahb", "ref"; + + resets = <&gcc GCC_USB0_PHY_BCR>, + <&gcc GCC_USB3PHY_0_PHY_BCR>; + reset-names = "phy","common"; + status = "disabled"; + + usb0_ssphy: phy@78200 { + reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ + <0x0 0x00078400 0x0 0x200>, /* Rx */ + <0x0 0x00078800 0x0 0x1f8>, /* PCS */ + <0x0 0x00078600 0x0 0x044>; /* PCS misc */ + #phy-cells = <0>; + #clock-cells = <0>; + clocks = <&gcc GCC_USB0_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "gcc_usb0_pipe_clk_src"; + }; + }; + + qusb_phy_0: qusb@79000 { + compatible = "qcom,ipq6018-qusb2-phy"; + reg = <0x0 0x00079000 0x0 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, + <&xo>; + clock-names = "cfg_ahb", "ref"; + + resets = <&gcc GCC_QUSB2_0_PHY_BCR>; + status = "disabled"; + }; + + pcie_phy: phy@84000 { + compatible = "qcom,ipq6018-qmp-pcie-phy"; + reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */ + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_PCIE0_AUX_CLK>, + <&gcc GCC_PCIE0_AHB_CLK>; + clock-names = "aux", "cfg_ahb"; + + resets = <&gcc GCC_PCIE0_PHY_BCR>, + <&gcc GCC_PCIE0PHY_PHY_BCR>; + reset-names = "phy", + "common"; + + pcie_phy0: phy@84200 { + reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */ + <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */ + <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */ + <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */ + #phy-cells = <0>; + + clocks = <&gcc GCC_PCIE0_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "gcc_pcie0_pipe_clk_src"; + #clock-cells = <0>; + }; + }; + + mdio: mdio@90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio"; + reg = <0x0 0x00090000 0x0 0x64>; + clocks = <&gcc GCC_MDIO_AHB_CLK>; + clock-names = "gcc_mdio_ahb_clk"; + status = "disabled"; + }; + prng: qrng@e1000 { compatible = "qcom,prng-ee"; reg = <0x0 0x000e3000 0x0 0x1000>; @@ -257,6 +375,41 @@ reg = <0x0 0x01937000 0x0 0x21000>; }; + usb2: usb@70f8800 { + compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; + reg = <0x0 0x070F8800 0x0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_USB1_MASTER_CLK>, + <&gcc GCC_USB1_SLEEP_CLK>, + <&gcc GCC_USB1_MOCK_UTMI_CLK>; + clock-names = "core", + "sleep", + "mock_utmi"; + + assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, + <&gcc GCC_USB1_MOCK_UTMI_CLK>; + assigned-clock-rates = <133330000>, + <24000000>; + resets = <&gcc GCC_USB1_BCR>; + status = "disabled"; + + dwc_1: usb@7000000 { + compatible = "snps,dwc3"; + reg = <0x0 0x07000000 0x0 0xcd00>; + interrupts = ; + phys = <&qusb_phy_1>; + phy-names = "usb2-phy"; + tx-fifo-resize; + snps,is-utmi-l1-suspend; + snps,hird-threshold = /bits/ 8 <0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + dr_mode = "host"; + }; + }; + blsp_dma: dma-controller@7884000 { compatible = "qcom,bam-v1.7.0"; reg = <0x0 0x07884000 0x0 0x2b000>; @@ -366,6 +519,49 @@ status = "disabled"; }; + usb3: usb@8af8800 { + compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; + reg = <0x0 0x08af8800 0x0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, + <&gcc GCC_USB0_MASTER_CLK>, + <&gcc GCC_USB0_SLEEP_CLK>, + <&gcc GCC_USB0_MOCK_UTMI_CLK>; + clock-names = "cfg_noc", + "core", + "sleep", + "mock_utmi"; + + assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, + <&gcc GCC_USB0_MASTER_CLK>, + <&gcc GCC_USB0_MOCK_UTMI_CLK>; + assigned-clock-rates = <133330000>, + <133330000>, + <24000000>; + + resets = <&gcc GCC_USB0_BCR>; + status = "disabled"; + + dwc_0: usb@8a00000 { + compatible = "snps,dwc3"; + reg = <0x0 0x08a00000 0x0 0xcd00>; + interrupts = ; + phys = <&qusb_phy_0>, <&usb0_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + clocks = <&xo>; + clock-names = "ref"; + tx-fifo-resize; + snps,is-utmi-l1-suspend; + snps,hird-threshold = /bits/ 8 <0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + dr_mode = "host"; + }; + }; + intc: interrupt-controller@b000000 { compatible = "qcom,msm-qgic2"; #address-cells = <2>; @@ -386,105 +582,6 @@ }; }; - pcie_phy: phy@84000 { - compatible = "qcom,ipq6018-qmp-pcie-phy"; - reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */ - status = "disabled"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - clocks = <&gcc GCC_PCIE0_AUX_CLK>, - <&gcc GCC_PCIE0_AHB_CLK>; - clock-names = "aux", "cfg_ahb"; - - resets = <&gcc GCC_PCIE0_PHY_BCR>, - <&gcc GCC_PCIE0PHY_PHY_BCR>; - reset-names = "phy", - "common"; - - pcie_phy0: phy@84200 { - reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */ - <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */ - <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */ - <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */ - #phy-cells = <0>; - - clocks = <&gcc GCC_PCIE0_PIPE_CLK>; - clock-names = "pipe0"; - clock-output-names = "gcc_pcie0_pipe_clk_src"; - #clock-cells = <0>; - }; - }; - - pcie0: pci@20000000 { - compatible = "qcom,pcie-ipq6018"; - reg = <0x0 0x20000000 0x0 0xf1d>, - <0x0 0x20000f20 0x0 0xa8>, - <0x0 0x20001000 0x0 0x1000>, - <0x0 0x80000 0x0 0x4000>, - <0x0 0x20100000 0x0 0x1000>; - reg-names = "dbi", "elbi", "atu", "parf", "config"; - - device_type = "pci"; - linux,pci-domain = <0>; - bus-range = <0x00 0xff>; - num-lanes = <1>; - max-link-speed = <3>; - #address-cells = <3>; - #size-cells = <2>; - - phys = <&pcie_phy0>; - phy-names = "pciephy"; - - ranges = <0x81000000 0x0 0x00000000 0x0 0x20200000 0x0 0x10000>, - <0x82000000 0x0 0x20220000 0x0 0x20220000 0x0 0xfde0000>; - - interrupts = ; - interrupt-names = "msi"; - - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc 0 75 - IRQ_TYPE_LEVEL_HIGH>, /* int_a */ - <0 0 0 2 &intc 0 78 - IRQ_TYPE_LEVEL_HIGH>, /* int_b */ - <0 0 0 3 &intc 0 79 - IRQ_TYPE_LEVEL_HIGH>, /* int_c */ - <0 0 0 4 &intc 0 83 - IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - - clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, - <&gcc GCC_PCIE0_AXI_M_CLK>, - <&gcc GCC_PCIE0_AXI_S_CLK>, - <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, - <&gcc PCIE0_RCHNG_CLK>; - clock-names = "iface", - "axi_m", - "axi_s", - "axi_bridge", - "rchng"; - - resets = <&gcc GCC_PCIE0_PIPE_ARES>, - <&gcc GCC_PCIE0_SLEEP_ARES>, - <&gcc GCC_PCIE0_CORE_STICKY_ARES>, - <&gcc GCC_PCIE0_AXI_MASTER_ARES>, - <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, - <&gcc GCC_PCIE0_AHB_ARES>, - <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, - <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; - reset-names = "pipe", - "sleep", - "sticky", - "axi_m", - "axi_s", - "ahb", - "axi_m_sticky", - "axi_s_sticky"; - - status = "disabled"; - }; - watchdog@b017000 { compatible = "qcom,kpss-wdt"; interrupts = ; @@ -617,147 +714,74 @@ }; }; - mdio: mdio@90000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio"; - reg = <0x0 0x00090000 0x0 0x64>; - clocks = <&gcc GCC_MDIO_AHB_CLK>; - clock-names = "gcc_mdio_ahb_clk"; - status = "disabled"; - }; - - qusb_phy_1: qusb@59000 { - compatible = "qcom,ipq6018-qusb2-phy"; - reg = <0x0 0x00059000 0x0 0x180>; - #phy-cells = <0>; - - clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, - <&xo>; - clock-names = "cfg_ahb", "ref"; - - resets = <&gcc GCC_QUSB2_1_PHY_BCR>; - status = "disabled"; - }; - - usb2: usb@70f8800 { - compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; - reg = <0x0 0x070F8800 0x0 0x400>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - clocks = <&gcc GCC_USB1_MASTER_CLK>, - <&gcc GCC_USB1_SLEEP_CLK>, - <&gcc GCC_USB1_MOCK_UTMI_CLK>; - clock-names = "core", - "sleep", - "mock_utmi"; - - assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, - <&gcc GCC_USB1_MOCK_UTMI_CLK>; - assigned-clock-rates = <133330000>, - <24000000>; - resets = <&gcc GCC_USB1_BCR>; - status = "disabled"; - - dwc_1: usb@7000000 { - compatible = "snps,dwc3"; - reg = <0x0 0x07000000 0x0 0xcd00>; - interrupts = ; - phys = <&qusb_phy_1>; - phy-names = "usb2-phy"; - tx-fifo-resize; - snps,is-utmi-l1-suspend; - snps,hird-threshold = /bits/ 8 <0x0>; - snps,dis_u2_susphy_quirk; - snps,dis_u3_susphy_quirk; - dr_mode = "host"; - }; - }; + pcie0: pci@20000000 { + compatible = "qcom,pcie-ipq6018"; + reg = <0x0 0x20000000 0x0 0xf1d>, + <0x0 0x20000f20 0x0 0xa8>, + <0x0 0x20001000 0x0 0x1000>, + <0x0 0x80000 0x0 0x4000>, + <0x0 0x20100000 0x0 0x1000>; + reg-names = "dbi", "elbi", "atu", "parf", "config"; - ssphy_0: ssphy@78000 { - compatible = "qcom,ipq6018-qmp-usb3-phy"; - reg = <0x0 0x00078000 0x0 0x1c4>; - #address-cells = <2>; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + max-link-speed = <3>; + #address-cells = <3>; #size-cells = <2>; - ranges; - - clocks = <&gcc GCC_USB0_AUX_CLK>, - <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; - clock-names = "aux", "cfg_ahb", "ref"; - - resets = <&gcc GCC_USB0_PHY_BCR>, - <&gcc GCC_USB3PHY_0_PHY_BCR>; - reset-names = "phy","common"; - status = "disabled"; - - usb0_ssphy: phy@78200 { - reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ - <0x0 0x00078400 0x0 0x200>, /* Rx */ - <0x0 0x00078800 0x0 0x1f8>, /* PCS */ - <0x0 0x00078600 0x0 0x044>; /* PCS misc */ - #phy-cells = <0>; - #clock-cells = <0>; - clocks = <&gcc GCC_USB0_PIPE_CLK>; - clock-names = "pipe0"; - clock-output-names = "gcc_usb0_pipe_clk_src"; - }; - }; - qusb_phy_0: qusb@79000 { - compatible = "qcom,ipq6018-qusb2-phy"; - reg = <0x0 0x00079000 0x0 0x180>; - #phy-cells = <0>; + phys = <&pcie_phy0>; + phy-names = "pciephy"; - clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, - <&xo>; - clock-names = "cfg_ahb", "ref"; + ranges = <0x81000000 0 0x20200000 0 0x20200000 + 0 0x10000>, /* downstream I/O */ + <0x82000000 0 0x20220000 0 0x20220000 + 0 0xfde0000>; /* non-prefetchable memory */ - resets = <&gcc GCC_QUSB2_0_PHY_BCR>; - status = "disabled"; - }; + interrupts = ; + interrupt-names = "msi"; - usb3: usb@8af8800 { - compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; - reg = <0x0 0x8af8800 0x0 0x400>; - #address-cells = <2>; - #size-cells = <2>; - ranges; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 75 + IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 78 + IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 79 + IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 83 + IRQ_TYPE_LEVEL_HIGH>; /* int_d */ - clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, - <&gcc GCC_USB0_MASTER_CLK>, - <&gcc GCC_USB0_SLEEP_CLK>, - <&gcc GCC_USB0_MOCK_UTMI_CLK>; - clock-names = "cfg_noc", - "core", - "sleep", - "mock_utmi"; + clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, + <&gcc GCC_PCIE0_AXI_M_CLK>, + <&gcc GCC_PCIE0_AXI_S_CLK>, + <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, + <&gcc PCIE0_RCHNG_CLK>; + clock-names = "iface", + "axi_m", + "axi_s", + "axi_bridge", + "rchng"; - assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, - <&gcc GCC_USB0_MASTER_CLK>, - <&gcc GCC_USB0_MOCK_UTMI_CLK>; - assigned-clock-rates = <133330000>, - <133330000>, - <24000000>; + resets = <&gcc GCC_PCIE0_PIPE_ARES>, + <&gcc GCC_PCIE0_SLEEP_ARES>, + <&gcc GCC_PCIE0_CORE_STICKY_ARES>, + <&gcc GCC_PCIE0_AXI_MASTER_ARES>, + <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, + <&gcc GCC_PCIE0_AHB_ARES>, + <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, + <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; + reset-names = "pipe", + "sleep", + "sticky", + "axi_m", + "axi_s", + "ahb", + "axi_m_sticky", + "axi_s_sticky"; - resets = <&gcc GCC_USB0_BCR>; status = "disabled"; - - dwc_0: usb@8a00000 { - compatible = "snps,dwc3"; - reg = <0x0 0x8a00000 0x0 0xcd00>; - interrupts = ; - phys = <&qusb_phy_0>, <&usb0_ssphy>; - phy-names = "usb2-phy", "usb3-phy"; - clocks = <&xo>; - clock-names = "ref"; - tx-fifo-resize; - snps,is-utmi-l1-suspend; - snps,hird-threshold = /bits/ 8 <0x0>; - snps,dis_u2_susphy_quirk; - snps,dis_u3_susphy_quirk; - dr_mode = "host"; - }; }; }; @@ -792,26 +816,4 @@ #interrupt-cells = <2>; }; }; - - rpm-glink { - compatible = "qcom,glink-rpm"; - interrupts = ; - qcom,rpm-msg-ram = <&rpm_msg_ram>; - mboxes = <&apcs_glb 0>; - - rpm_requests: glink-channel { - compatible = "qcom,rpm-ipq6018"; - qcom,glink-channels = "rpm_requests"; - - regulators { - compatible = "qcom,rpm-mp5496-regulators"; - - ipq6018_s2: s2 { - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1062500>; - regulator-always-on; - }; - }; - }; - }; };