From 6a1b660a83b262237b6bebed26e44db923a86a6b Mon Sep 17 00:00:00 2001 From: Zoltan HERPAI Date: Tue, 6 Jun 2023 18:09:19 +0000 Subject: [PATCH 71/90] sunxi: Move most board options to the board Kconfig This excludes options that are inherently ARM-specific or are specific to legacy non-DM drivers. Some help text is cleaned up along the way. Signed-off-by: Samuel Holland Signed-off-by: Zoltan HERPAI --- arch/arm/mach-sunxi/Kconfig | 71 ------------------------------------ board/sunxi/Kconfig | 72 +++++++++++++++++++++++++++++++++++++ 2 files changed, 72 insertions(+), 71 deletions(-) --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -548,16 +548,6 @@ config DRAM_ODT_CORRECTION then the correction is negative. Usually the value for this is 0. endif -config UART0_PORT_F - bool "UART0 on MicroSD breakout board" - ---help--- - Repurpose the SD card slot for getting access to the UART0 serial - console. Primarily useful only for low level u-boot debugging on - tablets, where normal UART0 is difficult to access and requires - device disassembly and/or soldering. As the SD card can't be used - at the same time, the system can be only booted in the FEL mode. - Only enable this if you really know what you are doing. - config OLD_SUNXI_KERNEL_COMPAT bool "Enable workarounds for booting old kernels" ---help--- @@ -571,20 +561,6 @@ config MACPWR Set the pin used to power the MAC. This takes a string in the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. -config MMC1_PINS_PH - bool "Pins for mmc1 are on Port H" - depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40 - ---help--- - Select this option for boards where mmc1 uses the Port H pinmux. - -config MMC_SUNXI_SLOT_EXTRA - int "mmc extra slot number" - default -1 - ---help--- - sunxi builds always enable mmc0, some boards also have a second sdcard - slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable - support for this. - config I2C0_ENABLE bool "Enable I2C/TWI controller 0" default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40 @@ -612,16 +588,6 @@ config R_I2C_ENABLE Set this to y to enable the I2C controller which is part of the PRCM. endif -config AXP_DISABLE_BOOT_ON_POWERON - bool "Disable device boot on power plug-in" - depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER - default n - ---help--- - Say Y here to prevent the device from booting up because of a plug-in - event. When set, the device will boot into the SPL briefly to - determine why it was powered on, and if it was determined because of - a plug-in event instead of a button press event it will shut back off. - config VIDEO_SUNXI bool "Enable graphical uboot console on HDMI, LCD or VGA" depends on !MACH_SUN8I_A83T @@ -850,41 +816,4 @@ config SPL_SPI_SUNXI sunxi SPI Flash. It uses the same method as the boot ROM, so does not need any extra configuration. -config PINE64_DT_SELECTION - bool "Enable Pine64 device tree selection code" - depends on MACH_SUN50I - help - The original Pine A64 and Pine A64+ are similar but different - boards and can be differed by the DRAM size. Pine A64 has - 512MiB DRAM, and Pine A64+ has 1GiB or 2GiB. By selecting this - option, the device tree selection code specific to Pine64 which - utilizes the DRAM size will be enabled. - -config PINEPHONE_DT_SELECTION - bool "Enable PinePhone device tree selection code" - depends on MACH_SUN50I - help - Enable this option to automatically select the device tree for the - correct PinePhone hardware revision during boot. - -config BLUETOOTH_DT_DEVICE_FIXUP - string "Fixup the Bluetooth controller address" - default "" - help - This option specifies the DT compatible name of the Bluetooth - controller for which to set the "local-bd-address" property. - Set this option if your device ships with the Bluetooth controller - default address. - The used address is "bdaddr" if set, and "ethaddr" with the LSB - flipped elsewise. - endif - -config CHIP_DIP_SCAN - bool "Enable DIPs detection for CHIP board" - select SUPPORT_EXTENSION_SCAN - select W1 - select W1_GPIO - select W1_EEPROM - select W1_EEPROM_DS24XXX - select CMD_EXTENSION --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -171,6 +171,78 @@ config SPL_IMAGE_TYPE default "sunxi_egon" if SPL_IMAGE_TYPE_SUNXI_EGON default "sunxi_toc0" if SPL_IMAGE_TYPE_SUNXI_TOC0 +config MMC_SUNXI_SLOT_EXTRA + int "MMC extra slot number" + default -1 + help + sunxi builds always enable mmc0. Some boards also have a + second SD card slot or eMMC on mmc1 - mmc3. Setting this to 1, + 2 or 3 will enable support for this. + +config MMC1_PINS_PH + bool "MMC1 pins are on Port H" + depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40 + help + Select this option on boards where mmc1 uses the Port H pinmux. + +config UART0_PORT_F + bool "UART0 pins are on Port F (MicroSD breakout board)" + help + Repurpose the SD card slot for getting access to the UART0 + serial console. Primarily useful only for low level u-boot + debugging on tablets, where normal UART0 is difficult to + access and requires device disassembly and/or soldering. As + the SD card can't be used at the same time, the system can be + only booted in FEL mode. Only enable this if you really know + what you are doing. + +config AXP_DISABLE_BOOT_ON_POWERON + bool "Disable device boot on power plug-in" + depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER + help + Say Y here to prevent the device from booting up because of a + plug-in event. When set, the device will boot into the SPL + briefly to determine why it was powered on, and if the board + was powered on because of a plug-in event instead of a button + press event, it will shut back off. + +config CHIP_DIP_SCAN + bool "Enable DIPs detection for CHIP board" + select SUPPORT_EXTENSION_SCAN + select W1 + select W1_GPIO + select W1_EEPROM + select W1_EEPROM_DS24XXX + select CMD_EXTENSION + +config PINE64_DT_SELECTION + bool "Enable Pine64 device tree selection code" + depends on MACH_SUN50I + help + The original Pine A64 and Pine A64+ are similar but different + boards and can be differed by the DRAM size. Pine A64 has + 512MiB DRAM, and Pine A64+ has 1GiB or 2GiB. By selecting this + option, the device tree selection code specific to Pine64 which + utilizes the DRAM size will be enabled. + +config PINEPHONE_DT_SELECTION + bool "Enable PinePhone device tree selection code" + depends on MACH_SUN50I + help + Enable this option to automatically select the device tree for the + correct PinePhone hardware revision during boot. + +config BLUETOOTH_DT_DEVICE_FIXUP + string "Fixup the Bluetooth controller address" + default "" + help + This option specifies the DT compatible name of the Bluetooth + controller for which to set the "local-bd-address" property. + Set this option if your device ships with the Bluetooth controller + default address. + The used address is "bdaddr" if set, and "ethaddr" with the LSB + flipped elsewise. + endmenu endif