Commit Graph

28336 Commits

Author SHA1 Message Date
Zoltan HERPAI
f01982ec0b sunxi: add testing kernel 6.1
Compile-tested: all targets
Runtime-tested:
 - Cortex-A53: Pine64+
 - Cortex-A7:  Bananapro, Orange Pi 2
 - Cortex-A8:  pcDuino v2

Patches refreshed.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-24 18:52:06 +02:00
Zoltan HERPAI
939d4d0b70 sunxi: copy patches from 5.15 to 6.1
To start the migration, we copy the patches from 5.15 to 6.1.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-24 18:51:51 +02:00
Shiji Yang
12f53724c6 ath79: fix first reboot issue on Netgear WNDR4300 v2 and WNDR4500 v3
From the Netgear u-boot GPL code[1]. Bootloader always unconditionally
marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead
to conflicts with the OpenWrt nand driver since these blocks may be good
blocks. In this case, U-boot will override the oob of these blocks so
that break the ubi volume. The system will be damaged after first reboot.
To avoid this issue, manually skip these blocks by using "mtd-concat".

[1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip

Fixes: https://github.com/openwrt/openwrt/issues/8878
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-08-24 00:04:38 +02:00
Shiji Yang
0f9b8aa3f5 ath79: rework Netgear nand devices image recipe
In Netgear u-boot GPL code, nand devices uses this formula to locate the
rootfs offset.

offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE;

Howerver, WNDR4500 source code incorrectly define the nand block size to
64k. In some cases, it causes u-boot can't get the correct rootfs offset,
which result in boot failure. This patch workaround it by padding kernel
size to (128k * n - 128 - 1). The additional char '\0' is used to ensure
the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE.

Fixes: https://github.com/openwrt/openwrt/issues/13050
Fixes: 3c1512a25d ("ath79: optimize the firmware recipe for Netgear NAND devices")
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-08-24 00:04:38 +02:00
David Bauer
4c0fdad7ea mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.

Both LED's are configured pulsing.

AMBER | 10/100
GREEN | 1000
A+G   | 2500

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 13:37:27 +02:00
Stefan Agner
4af06aaf33 mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
Stefan Agner
fa9d977f97 mediatek: filogic: wax220: support factory image
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.

The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.

This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.

Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.

References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz

* package/base-files/files/lib/upgrade/nand.sh:186
  Creation of rootfs_data is disabled

* Uboot-upstream/board/mediatek/common/ubi_helper.c
  Automatic creation of UBI backup volumes

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
David Bauer
c35ff41ccc mediatek: add missing packages for Acer Predator W6
Add missing packages for creating the overlay filesystem.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-08-22 12:24:34 +02:00
INAGAKI Hiroshi
ac68fbf526 ramips: add support for I-O DATA WN-DEAX1800GR
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.

Specification:

- SoC         : MediaTek MT7621A
- RAM         : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash       : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN        : 2.4/5 GHz (MediaTek MT7915)
- Ethernet    : 5x 10/100/1000 Mbps
  - Switch    : MT7530 (SoC)
- LEDs/Keys   : 6x/3x
- UART        : through-hole on PCB (J2)
  - assignment: 3.3V, GND, TX, RX from "1" marking
  - settings  : 115200n8
- Power       : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
   ("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing

Note:

- This device has 2x OS images on the flash storage. In this support,
  the first one will be used.

Warning:

- Do not use "saveenv" command on U-Boot CLI.
  This device has wrong u-boot-env data. The actual length of individual
  env data installed to the device is 0x1000 (4 KiB), but installed
  U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
  invalid. Then, if you perform saving environment data with saveenv on
  U-Boot CLI, installed env data will be overwritten with too few
  default values without individual values (SSID, password, MAC
  addresses, etc...).

MAC addresses:

LAN    : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN    : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz  : 50:41:B9:xx:xx:F5 (none)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
INAGAKI Hiroshi
9088b5445f ramips: improve sysupgrade helpers for I-O DATA devices
I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.)
have some important flags for booting, "bootnum" and "debugflag".
The almost devices have both flags but some devices have only
"bootnum" flag.
So optimize helper functions in iodata.sh to set each flags.

- both:
  - WN-AX1167GR2
  - WN-AX2033GR
  - WN-DX1167R
  - WN-DX1200GR
  - WN-DX2033GR

- "bootnum" only
  - WN-DEAX1800GR

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-08-20 01:26:15 +02:00
Bjørn Mork
6cc14bf66a filogic: support Telenor branded ZyXEL EX5700
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.

Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
  cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
  back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree

Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
  unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
  refuses to boot if it doesn't. The chosen "rootfs" volume must contain
  a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
  variable to the label mac.  But "factoryparams" does not always
  exist.  Instead there is a "RIP" volume containing all the factory
  data.  Copying the "RIP" volume to  "factoryparams" will fix this

Hardware
--------
SOC:   MediaTek MT7986
RAM:   1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI:  Mediatek MT7986 802.11ax 5 GHz
       Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH:   MediaTek MT7531 Switch + SoC
       3 x builtin 1G phy (lan1, lan2, lan3)
       2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB:   1 x USB 3.2 Enhanced SuperSpeed port
UART:  3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)

Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.2/24. Rename the image to C0A80101.img.

2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
   console, Interrupt the autoboot process by pressing ESC when prompted.

3. Download and boot the OpenWrt initramfs image.

   $ env set uboot_bootcount 0
   $ env set firmware nominal
   $ tftpboot
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
  OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
  not configured by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Bjørn Mork
1dd1ac2c35 mediatek: filogic: set wan label in preinit
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Thomas Kupper
4d79a65d60 ipq807x: add support for Netgear RAX120v2
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.

The majority of the code is based on @jewwest's PR #11830.

Specifications:
    * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
    * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
    * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
    * Ethernet: 4x 10/100/1000 Mbps LAN,
                1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
                1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
    * Wi-Fi:
        * 2.4 GHz: Qualcomm QCN5024 4x4
        * 2x 5 GHz: Qualcomm QCN5054 4x4
    * USB: 2x USB 3.0
    * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
    * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
    * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
    * Power: 19 VDC, 3.1 A

Installation:
    * Flashing OpenWrt is done in two steps:
        a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
           This writes an initramfs based OpenWrt image onto the RAX120v2
        b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline

    * U-Boot allows booting an initramfs image via TFTP:
    - Set ip of your PC to 192.168.1.100
        - At the serial console interrupt boot at "Hit any key to stop autoboot:"
        - In u-boot run `tftpsrv`
        - On your PC send the OpenWrt initramfs image:

          tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb

Make 5G Aquantia phy work:
    For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
    u-boot by writing the firmware to the correct mtd partition.

    The firmware file found in the Netgear stock firmware under /lib/firmware/ named
    'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
    be converted to a MBN file.

    The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
    under 'git_home/u-boot.git/tools/mkheader.py'

    Convert the CLD file to MBN using:
    $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn

    This MBN file can then be flashed to the MTD partition to be used by u-boot.

    The necessary files can also be found in
        https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware

    * Write MBN file to MTD partition to be loaded automatically by u-boot:

      U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
      corresponds to `/dev/mtd25` in OpenWrt.

        - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)

          $ fgrep -i 'ethphyfw' /proc/mtd
          mtd25: 00080000 00020000 "ethphyfw

        - copy mbn file to /tmp/ folder of the router

          $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/

        - write mbn file to ethphyfw partition

          $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25

Revert to stock firmware:
    * Flash the stock firmware to the bootloader using TFTP/NMRP.

References to RAX120v2 GPL source:
    https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-08-19 17:12:46 +02:00
Robert Marko
8ae8612210 ipq40xx: qca8k: add ageing setting support
qca8k driver we are currently based of is rather out of date and is lacking
support for setting the ageing time or fast ageing so until we update the
driver lets just backport support for those from qca8k.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-19 16:48:33 +02:00
Andreas Böhler
edfe91372a ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12
WiFi: 802.11a/b/g/n/ac SoC-integrated
USB: 1x 2.0

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m17
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd17 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 17
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Other Notes
===========

Contrary to the stock firmware, the USB port on the back can be used.

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-08-19 16:31:39 +02:00
Christian Marangi
6b63fcf8df
generic: 6.1: backport patch adding support for LED PHY
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-08-19 12:51:08 +02:00
Arınç ÜNAL
2214bab350 bcm53xx: add support for ASUS RT-AC3100
ASUS RT-AC3100 is ASUS RT-AC88U without the external switch.

OpenWrt forum users effortless and ktmakwana have confirmed that there are
revisions with either 4366b1 or 4366c0 wireless chips.

Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-08-19 11:03:11 +02:00
Arınç ÜNAL
b7ee8c9f83 bcm53xx: backport DT changes for ASUS RT-AC3100 queued for v6.6
Backport the patch that adds the DT for ASUS RT-AC3100.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-08-19 11:03:11 +02:00
John Audia
973c5d4a1d kernel: bump 5.15 to 5.15.127
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.127

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-18 23:14:08 +02:00
John Audia
93fabc05dc kernel: bump 6.1 to 6.1.46
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.46

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-08-18 23:12:29 +02:00
Rafał Miłecki
5356462ce5 Revert "kernel: switch back 5.15 to fw_devlink=permissive"
This reverts commit 79af0593a3.

A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.

Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-08-18 10:51:01 +02:00
Robert Marko
46ed38adeb ipq40xx: remove DK01 and DK04 boards
DK01 and DK04 board support has been in a form of 2 patches that we have
been carrying for a long time.
Both of the patches contain weird changes, dont follow any DT syntax and I
honestly doubt they are even valid.
DK01 and DK04 also have not been converted to DSA even after a long time
and I doubt that anybody in the community even has these boards as they are
QCA reference boards that are not even obtainable anymore.

Since patches for these 2 boards have been just causing us pain when trying
to update the kernel to a new major release or even point releases lets
remove the support for these boards, and if there are users they can easily
be reinstated.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:41:22 +02:00
Robert Marko
0e6982b253 ipq40xx: Use SoC DTSI for Teltonika RUTX
Teltonika RUTX currently is the only device pulling in DK01 DTSI and thus
preventing removal of DK01 and DK04 support.

So, lets add the missing nodes from DK01 DTSI and use the SoC DTSI instead.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:41:22 +02:00
Robert Marko
7661e164c0 ipq40xx: add header to SCM cold boot address patch
Lets add a proper commit title and description to the SCM cold boot
patch so it applies with a git apply or git-am.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:38:50 +02:00
Robert Marko
a4aac5909e ipq40xx: update SCM SDI patches with pending upstream
SCM SDI disable support is pending upstream, so lets use that instead.

Since the board check needs to be split out, export it with a header so
it applies with git-am.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-15 16:38:49 +02:00
Martin Schiller
0af88d2512 linux/named-gpio-export: add support for OPEN_DRAIN and OPEN_SOURCE flag
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.

We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2023-08-15 16:07:04 +02:00
Mathew McBride
7770d08e2b armsr: armv8: fix invalid symbol value for FSL_ENETC_QOS
The kernel FSL_ENETC_QOS option is only a compile time
option, it does not result in a separate module being built.

Set it to 'y' to resolve a warning from the kernel compile:

.config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c3151b6f04 ("armvirt: 64: add support for other SystemReady-compatible vendors")
2023-08-15 15:55:00 +02:00
Mathew McBride
9cb173e9f1 armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.

CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
0018b33531 armsr: armv8: package and select MDIO driver for Thunder SoC's
This MDIO driver was already being built, but not installed due
to being selected by the ThunderX Ethernet driver.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
7c5bdff9c4 armsr: add Marvell (Cavium) ThunderX2 network driver
The initial armv8 module incorrectly labelled the Thunder(v1) as
supporting the ThunderX2, when they have different drivers.

Add kmod-octeon-tx2 to support the newer devices.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
15d3536c9d armsr: armv8: synchronize PCIE related options with arm64 defconfig
This turns on various PCI related options which are enabled
in the Linux kernel arch/arm64/configs/defconfig but not
yet in the OpenWrt config.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
911ee97774 armsr: armv8: add bcmgenet (Raspberry Pi 4 GENET) to profile
kmod-bcmgenet is needed for Ethernet support on the
Raspberry Pi 4.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
27ca83c627 armsr: armv8: add Broadcom GENET and MDIO modules
These are used by common Broadcom SoC's like
the BCM2711 (RPi4) and iProc network processor.

Tested on the RPi4B using the Raspberry Pi
UEFI+ACPI firmware[1].

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://github.com/pftf/RPi4
2023-08-15 15:55:00 +02:00
Mathew McBride
df23eed179 armsr: armv8: enable Broadcom arch'es
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.

This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).

The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
1ff4f4df23 armsr: armv8: enable CONFIG_ARCH_RENESAS
Renesas markets several embedded Arm64 SoCs in the
RZ series (RZ/G, RZ/V), so should be enabled in
a general purpose target.

Automotive (R-Car) SoC's are not enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
45b445498b armsr: armv8: fix NXP/Freescale i.MX family configuration
Due to an error on my part, Anton Antonov's
i.MX changes[1] did not fully make it into my
armvirt kernel 6.1 EFI pull request. I have updated
them using the options he supplied[1] as well
as comparing to the Linux arm64 defconfig.

The notable exception is:
CONFIG_USB_DWC3_OF_SIMPLE currently disabled
due to an issue with i.MX8P and i.MX8Q.

Fixes: 3efb3b8 ("armvirt: 64: Add NXP i.MX 8M Mini/Nano/Quad/Plus EVK support")

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - ccf826c344
2023-08-15 15:55:00 +02:00
Mathew McBride
c4c60e4b19 armsr: enable ACPI_BUTTON
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.

ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
22e0c7be47 armsr: armv8: sync CPU features, EFI, CMA and scheduler options with Linux defconfig
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
e505873e65 armsr: armv8: enable KVM host
x86/64 enables support for KVM so I can't see a reason why
not on armsr/armv8 as well.

Arm CPU errata workaround items related to virtualization
are also enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Mathew McBride
5c4239ac3f armsr: armv8: sync Arm64 erratum options with kernel defconfig
To reduce differences with the Linux arm64 defconfig,
sync the enabled erratum items with defconfig.

There are still some options not selected due to
CONFIG_KVM or other options not enabled in OpenWrt
by default.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-15 15:55:00 +02:00
Hauke Mehrtens
54d470ed0e x86: Add virtualization time sync support
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.

Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-08-14 20:13:12 +02:00
Hauke Mehrtens
ff71035751 x86: Activate CONFIG_PCIEASPM
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.

Fixes: #13248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-08-14 20:10:29 +02:00
Ivan Pavlov
54e5e396c5 ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2023-08-14 20:08:05 +02:00
Robert Marko
f1c80445bd ipq40xx: meraki: define DTB load address
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.

Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.

Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.

Reviewed-by: Lech Perczak lech.perczak@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:29:25 +02:00
Robert Marko
bb4a25860f ipq40xx: meraki: remove swconfig in DEVICE_PACKAGES
ipq40xx was converted to DSA and swconfig is not being included at all in
the default packages so there is no need to drop it from device packages.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:28:56 +02:00
Robert Marko
9e9dc1890c ipq40xx: commonize Meraki recipe
MR33 and MR74 share pretty much everything in the image recipe, so lets
extract a common recipe to avoid duplication.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-08-14 19:28:56 +02:00
Daniel Golle
e6f8b69918 generic: backport fix for Winbond SPI NAND
Avoid using stack allocated memory for DMA operations.

Fixes: 156c00dedc ("generic: backport Winbond W25N02KV SPI-NAND support")
Fixes: b71c870caa ("generic: 6.1: re-add two Winbond nand fixes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:37 +01:00
Daniel Golle
42e14d3ed8 generic: 5.15: rename patches to match correct version
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:37 +01:00
Daniel Golle
c524a76f4c armsr: remove redundant phy-marvell-10g module
the Marvell 10G PHY driver is no way specific to ARM SystemReady
systems, it frequently occurs on SFP+ copper modules and is useful on
many targets.

Hence it been added to package/kernel/linux/modules/netdevices and we
can remove the now redundant target-specific module.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:36 +01:00
Daniel Golle
0454691960 mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-13 15:01:36 +01:00