Commit Graph

283 Commits

Author SHA1 Message Date
Ram Chandra Jangir
e178d51a04 ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Ram Chandra Jangir
5e1cc0c090 ipq806x: Updated various ipq40xx pin definitions
This change populates default values for various GPIO functions
in ipq40xx pinctrl driver.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Ram Chandra Jangir
7bf74d3185 ipq806x: add qpic nand and bam dma node's in ipq4019 dts tree
This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-05-29 07:26:03 +02:00
Ram Chandra Jangir
35307c0bbf ipq806x: Add support for custom data mapping in bam_dma dmaengine
This change adds a new function to support for preparing DMA descriptor
for custom data.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-05-29 07:25:59 +02:00
Ram Chandra Jangir
ea9e0cf2ce ipq806x: Added bam transaction and support additional CSRs
This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-05-29 07:25:54 +02:00
Ram Chandra Jangir
2048cab22b ipq806x: Add bam_dma support in qcom_nand driver
The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-05-29 07:25:46 +02:00
Ram Chandra Jangir
d227bb06df ipq806x: Add support to configure ipq40xx GPIO_PULL bits
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-05-29 07:25:39 +02:00
Hauke Mehrtens
0b17375931 kernel: update kernel 4.9 to 4.9.30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-27 00:48:37 +02:00
Mathias Kresin
822ee54544 treewide: fix device tree path in scripts
The device tree is at /proc/device-tree/ without a base subdir.

Fixes: da472e5b30 ("treewide: access device tree from userspace via /proc/")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 15:18:30 +02:00
Mathias Kresin
da472e5b30 treewide: access device tree from userspace via /proc/
Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Koen Vandeputte
e842e16f45 kernel: update kernel 4.9 to 4.9.29
- Refresh all patches
- Removed upstreamed
- Adapted 1

Compile tested on: bcm53xx, cns3xxx, imx6, lantiq
Run tested on: cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[update from 4.9.28 to 4.9.29]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:51:22 +02:00
Jo-Philipp Wich
3c3f7cfe4d ipq806x: fix EA8500 switch configuration
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.

Ref: https://github.com/openwrt/luci/issues/1086

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-03 14:15:34 +02:00
Thomas Reifferscheid
956e31b1e4 ipq8064: fix dwc3-of-simple module unloading for Netgear R7500
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:

root@LEDE:/# rmmod dwc3-of-simple
[   21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.391931] usb usb4: USB disconnect, device number 1
[   21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.406685] usb usb3: USB disconnect, device number 1
[   21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.

Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.

At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.

root@LEDE:/# rmmod dwc3
[   53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.827412] usb usb4: USB disconnect, device number 1
[   53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.842314] usb usb3: USB disconnect, device number 1
[   53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.857882] usb usb2: USB disconnect, device number 1
[   53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.873696] usb usb1: USB disconnect, device number 1
[   53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#

For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0

The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.

Now unloading and repeated module loading is working just fine.

root@LEDE:/# rmmod dwc3-of-simple
[   24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.089765] usb usb4: USB disconnect, device number 1
[   24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.104522] usb usb3: USB disconnect, device number 1
[   24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.120396] usb usb2: USB disconnect, device number 1
[   24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.135948] usb usb1: USB disconnect, device number 1
[   24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#

Fixes: dwc3-of-simple module unloading for Netgear R7500

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-04-24 09:20:23 +02:00
Thomas Reifferscheid
8db079a9ff ipq8064: Fix dwc3 module unloading
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
2017-04-24 09:19:49 +02:00
Mathias Kresin
226e194335 generic: mtd: backport mx25u25635f stateless 4b support
Use the stateless 4-byte op codes for this flash chip to fix reboot
hangs on SoCs expecting the flash chip in 3-byte mode.

Fixes: FS#179

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-19 21:00:52 +02:00
Mathias Kresin
8b3fa168b4 firmware: rework fritz-tools package
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.

Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.

Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.

Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Hauke Mehrtens
b26e34214c kernel: update kernel 4.9 to 4.9.20
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-04-02 12:47:55 +02:00
Thomas Reifferscheid
17f60b1cd2 ipq8064: fix dwc3-of-simple module unloading
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:

root@LEDE:/# rmmod dwc3-of-simple
[   21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.391931] usb usb4: USB disconnect, device number 1
[   21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   21.406685] usb usb3: USB disconnect, device number 1
[   21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.

Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.

At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.

root@LEDE:/# rmmod dwc3
[   53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.827412] usb usb4: USB disconnect, device number 1
[   53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   53.842314] usb usb3: USB disconnect, device number 1
[   53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.857882] usb usb2: USB disconnect, device number 1
[   53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   53.873696] usb usb1: USB disconnect, device number 1
[   53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#

For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0

The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116

Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.

root@LEDE:/# rmmod dwc3-of-simple
[   24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.089765] usb usb4: USB disconnect, device number 1
[   24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   24.104522] usb usb3: USB disconnect, device number 1
[   24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.120396] usb usb2: USB disconnect, device number 1
[   24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   24.135948] usb usb1: USB disconnect, device number 1
[   24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#

Fixes: dwc3-of-simple module unloading

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-28 09:03:55 +02:00
Thomas Reifferscheid
c75f059b0c ipq8064: Fix dwc3 module unloading
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with       (phy, offset, value, mask)

The patch is swapping value and mask.

Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:

root@LEDE:/# rmmod dwc3
[   19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   19.168084] usb usb4: USB disconnect, device number 1
[   19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   19.182960] usb usb3: USB disconnect, device number 1
[   19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
[   19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   19.205912] usb usb2: USB disconnect, device number 1
[   19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   19.221751] usb usb1: USB disconnect, device number 1
[   19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[   19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[   29.583343] phy phy-100f8830.phy.4: phy init failed --> -110
[   29.583399] dwc3 10000000.dwc3: failed to initialize core
[   29.588169] dwc3: probe of 10000000.dwc3 failed with error -110
[   29.652943] phy phy-110f8830.phy.2: phy init failed --> -110
[   29.652988] dwc3 11000000.dwc3: failed to initialize core
[   29.657735] dwc3: probe of 11000000.dwc3 failed with error -110
root@LEDE:/#

With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[   22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   22.622298] usb usb4: USB disconnect, device number 1
[   22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[   22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[   22.637054] usb usb3: USB disconnect, device number 1
[   22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[   22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   22.652910] usb usb2: USB disconnect, device number 1
[   22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[   22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[   22.668604] usb usb1: USB disconnect, device number 1
[   22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[   25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[   25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[   25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[   25.426509] hub 1-0:1.0: USB hub found
[   25.431626] hub 1-0:1.0: 1 port detected
[   25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[   25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[   25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[   25.452926] hub 2-0:1.0: USB hub found
[   25.460420] hub 2-0:1.0: 1 port detected
[   25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[   25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[   25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[   25.546583] hub 3-0:1.0: USB hub found
[   25.551997] hub 3-0:1.0: 1 port detected
[   25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[   25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[   25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[   25.573063] hub 4-0:1.0: USB hub found
[   25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#

Fixes: dwc3 module unloading

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-28 09:02:38 +02:00
Thomas Reifferscheid
e52117354c ipq8064: enable 2nd USB port on R7500
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.

Fixes FS#497

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-27 08:15:37 +02:00
Pavel Kubelun
9ac4c1dcee ipq806x: tsens: convert degrees to millicelsius
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.

Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-27 08:05:10 +02:00
Pavel Kubelun
dc32d0a53c ipq806x: add ipq806x specific tsens driver
Current upstream driver doesnt fully support ipq806x devices
ipq806x has 11 sensors, the upstream one doesn't allow to check
sensors 0-4, only 5-10.

A specific driver for ipq806x has been found in Qualcomm SDK repo.

https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c089e464cd7ce652419a0dc44d7959ce4d24b8a5
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c23d94b702c4182862e7f5051a2b7d00bb922a29
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=742f3684b62a6b9f082cb49404b1a92dc0b16bf5
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c0a9b2e2a382c152fa128f5b864c800dd6dfb311

Merging it into LEDE with this commit.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-27 08:05:10 +02:00
Hauke Mehrtens
fb7ea71c15 kernel: update kernel 4.9 to 4.9.17
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-26 12:23:19 +02:00
Mathias Kresin
86a0cbb333 treewide: select ath10k firmware explicit
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Thomas Reifferscheid
b69807e2b2 ipq806x: fix Netgear X4 R7500 ath10k firmware selection
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-03-24 08:09:39 +01:00
John Crispin
666bfc6fb5 Revert "ipq806x: make the dwc3 driver and required phy drivers built-in"
This reverts commit d5b10bb560.

This caused boot errors on some ipq8 boards

Signed-off-by: John Crispin <john@phrozen.org>
2017-03-23 08:29:44 +01:00
John Crispin
3a3564ead5 ipq806x: remove v4.4 support
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
ef6c4cc4ee ipq806x: set v4.9 as default
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
d5b10bb560 ipq806x: make the dwc3 driver and required phy drivers built-in
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
John Crispin
7dc5617173 ipq806x: enable QCE hardware crypto inside the kernel
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Christian Lamparter
c2d50bdeb3 ipq806x: add ipq4019 support
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Hannu Nyman
3f9eadf599 ipq806x: support independent core clocks in cpufreq with kernel 4.9+
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9

* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2017-03-20 08:12:49 +01:00
Pavel Kubelun
ef4ca01d6f ipq806x: route gpio interrupts to APPS processor through scm firmware
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-20 08:11:29 +01:00
Pavel Kubelun
0d89650db1 ipq806x: remove scm firmware clocks
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.

By design unlike other qcom boards ipq do not use clocks to connect to scm.

Considering this we're removing from DT and scm driver clocks for ipq boards.

As a result cpuidle does not produce errors about failed configuration anymore.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-03-20 08:11:29 +01:00
Felix Fietkau
894ee9510b ipq806x: fix ethernet DMA parameters with linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 21:42:47 +01:00
Felix Fietkau
7ffaf71d53 ipq806x: fix pcie with linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 21:10:31 +01:00
Felix Fietkau
5267ff2b6a ipq806x: re-enable the RAM clock for gcc on 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:57 +01:00
Felix Fietkau
2029167b56 ipq806x: fix crash on 4.9 if the rpm clock probe happens before cpuidle init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
Felix Fietkau
2a4baf3e79 ipq806x: fix NAND support for linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
Felix Fietkau
6006227cb7 ipq806x: do not allocate coherent memory in dma engine hotpath
The available amount of coherent DMA memory is very limited. On Linux
4.4 this issue was worked around by increasing the pool size.

It turns out that using coherent memory here is completely unnecessary.
This change reworks the driver code to use kzalloc+dma_map_single
instead.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:56 +01:00
John Crispin
1adf51702e ipq806x: clean up patches, port missing patches from 4.4
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-13 13:40:55 +01:00
John Crispin
99b6aefd63 ipq806x: sync 4.9 kernel config with 4.4
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:40:46 +01:00
Felix Fietkau
a531d37fab ipq806x: clean up dts patching in 4.9
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:33:51 +01:00
Felix Fietkau
ddf577b0b2 ipq806x: enable cmdline mangle on 4.9 (like on 4.4)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:33:50 +01:00
Hauke Mehrtens
9a065fcfec kernel: update kernel 4.9 to 4.9.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-03-12 15:45:50 +01:00
Felix Fietkau
92b5b360fe ipq806x: clean up dts patch
Move dts files to files/, remove useless patch chunks

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-08 14:38:22 +01:00
Felix Fietkau
2a3952bcd5 kernel: re-apply 300-arch-arm-force-ZRELADDR-on-arch-qcom.patch on 4.9 (FS#549)
Fixes memory corruption issues. See commit bdcba36442 for more
details.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-08 14:38:22 +01:00
Felix Fietkau
9f09bd6606 ipq806x: refresh patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-03-08 14:38:22 +01:00
Thomas Reifferscheid
eb09d79c16 ipq806x: sanitize Dni image generation
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
2017-02-26 13:32:26 +01:00