ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.
OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.
Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193)
NC GND NC
Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
.bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This extracts the model part of the board name and uses it for the
LED string identifiers in 01_leds. As this makes statements more
generic, it will allow to merge more cases in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Until now only HW modded SPI flash version was supported.
BCM6328 with 64M RAM and 128M NAND.
More info: https://openwrt.org/toh/sercomm/ad1018
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.
For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
