56cb2d4 nas: add decoding of cell_id
9a9019a uqmi: wms - added storage to read text messages
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51c442c265)
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ee7cb5e885)
Modems used in ZTE mobile broadband routers require to query the data
session status using the same CID as one used to establish the session,
otherwise they will report the session as "disconnected" despite
reporting correct PDH in previous step. Without this change, IPv6
connection on these modems doesn't establish properly. In IPv4 this bug
is present as well, but for some reason querying of IPv4 status works
using temporary CID, this however seems noncompliant with QMI
specifications, so fix it as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
e303ba8 uqmi: update code generator
7880de8 uqmi: sync data from libqmi project
d647f8d uqmi: add more diagnostics commands
6f95626 uim: add --uim-get-sim-state
Use newly introduce --uim-get-sim-state command to query PIN status
from modems which require using uim instead of dms command for that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With some debug in qmi.sh using following patch, some errors are visible
in the registration step
@@ -29,6 +29,7 @@ proto_qmi_init_config() {
}
proto_qmi_setup() {
+ set -x
local interface="$1"
local dataformat connstat plmn_mode mcc mnc
local device apn auth username password pincode delay modes pdptype
@@ -224,6 +225,8 @@ proto_qmi_setup() {
fi
done
+ registration=$(uqmi -s -d "$device" --get-serving-system)
+
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
During the boot of the system, modem could not start automatically its
network registration.
netifd: wan (9235): + echo 'Waiting for network registration'
netifd: wan (9235): Waiting for network registration
netifd: wan (9235): + local 'registration_timeout=0'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + grep '"searching"'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}'
netifd: wan (9235): + '[' -n ]
netifd: wan (9235): + echo 'Starting network wan'
As the while loop checks only "searching" pattern, uqmi.sh script quits
searching loop and continues whereas the modem is not registered
Other issue, after X seconds modem stops searching.
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ]
netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ]
netifd: wan (9213): + let registration_timeout++
netifd: wan (9213): + sleep 1
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + registration='{"registration":"not_registered"}'
netifd: wan (9213): + '[' -n ]
netifd: wan (9213): + echo 'Starting network wan'
netifd: wan (9213): Starting network wan
If registration_timeout is not expired, registration can be restarted
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
Tested-by: Florian Eckert <fe@dev.tdt.de>
Setting the plmn to '0' (auto) will implicitly lead to a (delayed)
network re-registration, which could further lead to some timing
related issues in the qmi proto handler.
On the other hand, if you switch back from manual plmn selection
to auto mode you have to set it to '0', because this setting is
permanently "saved" in the wwan module.
Conclusion:
If plmn is configured, check if it's already set euqally in the module.
If so, do nothing. Otherwise set it.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There already was an option for autoconfiguring IPv4 from QMI but this
was removed by commit 3b9b963e6e ("uqmi: always use DHCP for IPv4").
DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd
support for IPv4 autoconf from QMI but this time allow to configure this
for IPv4 and IPv6 independently and keep DHCP default on IPv4.
Signed-off-by: Filip Moc <lede@moc6.cz>
Give possibility to wait forever the registration by setting timeout
option to 0.
No timeout can be useful if the interface starts whereas no network is
available, because at the end of timeout the interface will be stopped
and never restarted.
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
There are mobile carrier who have different MTU size in their network.
With this change it is now possible to configure this with the qmi
proto handler.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Fix an issue where subinterfaces were not added to the same
firewall zone as their parent.
Fixes: FS#2122
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Apparently this modem replies differently to attempted --get-pin-status
which makes the script fail if a pincode is set. Fix this.
Manufacturer: Sierra Wireless, Incorporated
Model: MC7455
Revision: SWI9X30C_02.24.05.06 r7040 CARMD-EV-FRMWR2 2017/05/19 06:23:09
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Check pin count value from pin status and stop verification the pin if
the value is less then 3. This should prevent the proto-handler to
lock the SIM. If SIM is locked then the PUK is needed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Load the json output from uqmi --get-pin-status command and evaluate the
"pin1_status" value.
The following uqmi "pin1_status" values are evaluated:
- disabled
Do not verify PIN because SIM verification is disabled on this SIM
- blocked
Stop qmi_setup because SIM is locked and a PUK is required
- not_verified
SIM is not yet verified. Do a uqmi --verify-pin1 command if a SIM is
specified
- verified:
Do not verify the PIN because this was already done before
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if SIM does not get initialized.
To fix this stop polling pin status and notify netifd. Netifd will generate
then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if it is unable to registrate to
the mobile network. To fix this stop polling network registration status
and notify netifd. Netifd will generate then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This value will be used for now during following situations:
* Ask the sim with the uqmi --get-pin-status command.
* Wait for network registration with the uqmi --get-serving-system command.
This two commands wait forever in a while loop. Add a timeout to stop
waiting and so inform netifd.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Move uqmi std and error output on commands without using them to /dev/null.
This will remove useless outputs in the syslog.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Allow setting specific routing tables via the ip4table and ip6table
options also when ${ifname}_4 and ${ifname}_6 child interfaces are
being created.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The control device /dev/cdc-wdm0 is not available immediately on the
D-Link DWR-921 Rev.C3, therefore the wwan interface fails to start at
boot with a "The specified control device does not exist" error.
This patch alters /lib/netifd/proto/qmi.sh to wait for
network.wwan.delay earlier, before checking for the control device,
instead of just before interacting with the modem.
One still has to use network.wwan.proto='qmi', as the "wwan" proto
performs that sort of check before any delay is possible, failing with a
"No valid device was found" error.
Signed-off-by: Thomas Equeter <tequeter@users.noreply.github.com>
Pipe uqmi output from qmi_wds_stop function into /dev/null.
This will supress the following output in proto teardown.
netifd: wwan (x): "No effect"
netifd: wwan (x): Command failed: Permission denied
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The current implementation only checked if uqmi itself executed
correctly which is also the case when the returned value is actually
an error.
Rework this, checking that CID is a numeric value, which can only
be true if uqmi itself also executed correctly.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
uqmi contains a command for directly querying the modem if there
is a valid data connection, so let's use it.
This avoids the cases were all previous tests are succesful, but the
actual data link is not up for some reasons, leading to states were we
thought the link was up when it actually wasn't ..
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Originally, the implementation only checked if uqmi command
execution succeeded properly without actually checking it's returned data.
This lead to a pass, even when the returned data was indicating an error.
Rework the verification to actually check the returned data,
which can only be correct if the uqmi command itself also executed correctly.
On command execution success, value "pdh_" is a pure numeric value.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Debugging shows that using the general method properly cleans on each
run, while the method specifying the client-ID shows "No effect"
even while in connected state.
Fixes several connectivity issues seen on specific modems.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If a device only supports the 2nd verification method (uim),
the first method will fail as expected reporting an error:
"Command not supported"
Silence both separate methods and only report an error regarding
pin verification if both fail.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Some newer LTE modems, like the MC7455 or EC25-E do not support
"802.3" mode, and will stay in "raw-ip" regardless of the mode being
set.
In this case, the driver must be informed that it should handle all
packets in raw mode. [1]
This commit fixes connectivity issues for these devices.
Before:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending discover
udhcpc: sending discover
After:
[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending select for 100.66.245.226
udhcpc: lease of 100.66.245.226 obtained, lease time 7200
udhcpc: ifconfig wwan0 100.66.245.226 netmask 255.255.255.252 broadcast
+
udhcpc: setting default routers: 100.66.245.225
[1] https://lists.freedesktop.org/archives/libqmi-
devel/2017-January/002064.html
Tested on cns3xxx using a Sierra Wireless MC7455 LTE-A
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[bumped PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Newer devices tend to only support the newer version of the pin
verification command, so also try that one.
Fixes PIN issues with modems like the Sierra Wireless MC7455
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
If you unplug a QMI device, the /dev/cdc-wdmX device
disappears but uqmi will continue to poll it endlessly.
Then, when you plug it back, you have 2 uqmi processes,
and that's bad, because 2 processes talking QMI to the
same device [and the same time] doesn't seem to work well.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This reverts the following commits:
fbe522d120278ad007ee863888e44f96daf6352fcfd83555fc
This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
uqmi has the possibility to allow the modem to start a regsitration
process only to this specified plmn
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Add uqmi 'sync' command call to release stalled cid when preparing to
setup new connection. As a result it prevents 'POLICY MISMATCH' errors.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
8ceeab6 uqmi: Change returned value to QMI_CMD_REQUEST for 'sync' command.
1dc7be1 uqmi: Add sync command to release all cids.
Signed-off-by: John Crispin <john@phrozen.org>
It's useful when using multiple usb devices that should be bound to
certain usb ports. Symlinks are created by hotplug handlers.
Signed-off-by: Nickolay Ledovskikh <nledovskikh@gmail.com>
