This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N
Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.
Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This change the switch settings for:
HC5661: 4 lan ports + 1 wan port
Y1S: 2 lan ports(G port) + 2 lan ports(E port) + 1 wan port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
netdev on eth0.2 can't show link status of wan port because eth0 is
connected to builtin switch and is always link up. Use swconfig
trigger instead.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit made the following changes to sync all bootcount scripts:
1. use boot() instead of start()
This script only needs to be executed once when boot is complete.
use boot() to make this explicit.
2. drop sourcing of /lib/functions.sh
This is aready done in /etc/rc.common.
3. ramips: replace board name checking with a case
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lan and Wan addresses are swapped compared to the original firmware.
This patch fixes this problem
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
In commit d93969a13a ("ramips: Improve compatible for TP-Link
Archer devices") and subsequent ones, names of several devices
in ramips have been changed.
Since LED names are frequently invoked by $boardname, this has
broken LED setup in 01_leds, as $boardname and prefix in DTS
do not match anymore.
This patch updates device name prefixes for LEDs in DTS files,
and provides a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HiWiFi HC5761A is an "MT7628AN variant" of HC5761
Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet
Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot
Known bug:
- SD slot does not work (See PR 1500)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
HC5661A:
- Fix pinctrl
- Fix image size (15808k)
- Use switch trigger for WAN LED
Both:
- Use tpt LED trigger for wireless
- Explicitly disable USB nodes
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
There's an empty case in 02_network introduced by last commit. Drop it.
Fixes: ee650ba46c ("ramips: remove needless setting of lan_mac to eth0 in 02_network")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This removes superfluous lines like
lan_mac=$(cat /sys/class/net/eth0/address)
Since lan_mac only sets the MAC address for eth0.1, these lines
can be safely removed as the address will be inherited from eth0
anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The vast majority of devices labels "factory" partition with lower
case. Convert the small fraction with capital letter to that and
merge another case in 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This just merges some duplicate definitions and consolidates lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated
cases for phicomm k2p]
Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses
at 0xe000/0xe006 of factory partition.
Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network
uses lan_mac+1.
Add a special case reading lan/wan mac address for Phicomm K2P.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()
It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")
This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes a forgotten case in previous commit.
Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Having converted the target to use device compatible, ramips.sh
is obsolete now.
The only remaining entry for the mt7688 evaluation board seems to
be orphaned.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.
As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.
Despite that, base-files are updated, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Include "Archer" in compatible as it is part of the device name.
Update Makefile device names where necessary to match compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.
- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
Installation:
- copy the
'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
the orange led starts blinking (~6sec)
Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
Similiar to the lantiq target use a dts alias to define the wlan led
instead of static mapping in /etc/board.d/01_leds. Reduce code
duplication.
A device tree must define the alias "led-wlan" similiar to "led-boot".
/ {
aliases {
led-wlan = &led_wlan;
};
[..]
led_wlan: wlan {
label = "tl-wr841n-v14:green:wlan";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
};
};
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hardware specs:
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB: 1x 3.0
PCI: 3x Mini PCIe
GPS: Quectel L70B
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation:
The stock image is a modified openwrt and can be overflashed via
# sysupgrade -F image.bin
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
This patch fix and enable GELAN port in D-LINK DWR-118-A2.
Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.
Performed cleanup:
* generic DTS node names
* regulator for usb power
* added missing pinctrl groups
* use switch port instead of VLAN as trigger for WAN LED
Fixes for WNDR3700v5:
* all LEDS work
* correct ethernet MAC addresses
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
