Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.
SoC:
Octeon Cavium 7130 (Cavium 3)
Clocked at 1000Mhz
Memory:
1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
- mtd:
8 MiB (Macronix MX25L6408EMI-12G)
used for uboot/eeprom
- emmc:
4 GiB (SanDisk SDIN7DP2-4G)
used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used
All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.
There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.
All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.
Phy mapping:
- Phy5 is connected to physical eth0 port
- Phy6 is connected to physical eth1 port
- Phy7 is connected to physical eth2 port
- Phy4 is connected to physical eth3 port
Why this device needs external dts:
- faster boot time since need to initialize less device tree nodes.
- to add actual indication with LED about boot/failure/upgrade.
i.e. user could know when to enter failsafe mode or if upgrade is done
- reset button support so user can reset their device in case off failure
- sfp port indication in dmesg with information about sfp module
it also indicates when module inserted or removed
Octeon quirks:
- There is no port status available before it interface brought up
- SFP port can not be tied to actual phy due to octeon-ethernet state
and currently we can only get reports a about SFP state in dmesg
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to edgerouter 4 front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to edgerouter 4
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have edgerouter 4 running openwrt
Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is deactivated everywhere, just set this in the generic config.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update config with make kernel_oldconfig.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, redo kernel_oldconfig, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
