Fix NAND flash layout which was out-of-sync with the definition in
ARM TrustedFirmware-A which expects UBI to start at 0x200000.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
This reverts commit 997ff740dc.
78cbd5apick as it should be fixed in commit 78cbd5a57e11 ("tools: macOS:
types.h: fix missing unsigned types").
References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".
Sync SPI-NAND driver for mediatek to fixes this:
* Add support for Winbond W25N01KV 1Gbit chip.
* Add support for Etron SPI-NAND chip.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
WED requires a bunch of additional reserved memory regions. As U-Boot's
LMB allocator defaults to a maximum of only 8 regions, this currently
makes using WED impossible.
Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards
with a SoC supporting WED.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to fix build failure caused by a missing header which had
previously been implicitely included.
Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Among the patches adding support for MT7988 also came the switch to
use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE.
Take care of our downstream boards which did not have a 'memory' node in
their device trees.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The image_header_t typedef has been removed from
uboot v2023.01 [1], replaced with legacy struct.
[1] f3543e6944
Fixes: 3d5c542 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_SYS_TEXT_BASE has been renamed to CONFIG_TEXT_BASE
in uboot v2023.01 [1], fixes all this variable.
[1] 984639039f
Fixes: 3d5c5427 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move defines from header to defconfig
The package build and the Buildbot hang in 'make syncconfig' for
u-boot-ravpower_rp-wd009 because CONFIG_SYS_MIPS_TIMER_FREQ is not in
the .config, causing a console prompt. Also moved two other defines in
defconfig causing duplicate definition warnings.
Fixes: 3d5c5427e1 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
