Commit Graph

48241 Commits

Author SHA1 Message Date
Adrian Schmutzler
b123ffdf6e ath79: drop redundant status for gpio target-wide
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Adrian Schmutzler
dc1280ef65 ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.

So, do not disable it in the first place, and drop all device-specific
status statements afterwards.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Leon M. George
a0bb356612 ath79: add support for Compex WPJ344
Specifications:

SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '6A08':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin

MAC addresses:

<&uboot 0x2e010>  *:99  (label)
<&uboot 0x2e018>  *:9a
<&uboot 0x2e020>  *:9b
<&uboot 0x2e028>  *:9c

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Paul Spooren
f09b9319c6 build,json: store arch_packages in profiles.json
The `arch_packages` contains the supported package architecture.

Previously it was necessary to parse the `Packages` index for the line
`Architecture:`, requiring both an additional parser and file download.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-07-03 15:28:05 +01:00
Hans Dedecker
9858a8c582 odhcpd: bump to latest git HEAD
5da5299 odhcpd: fix compilation with GCC10

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-07-02 22:28:06 +02:00
Sungbo Eo
736995ce19 ath79: rearrange nand node by register address
All other nodes in the DTS are placed in order of address space. Harmonize
the nand nodes as well.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-02 21:34:37 +02:00
Hans Dedecker
cbb66f9edb curl: bump to 7.71.0
For changes in 7.71.0; see https://curl.haxx.se/changes.html#7_71_0

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-07-01 22:19:50 +02:00
Álvaro Fernández Rojas
f786de2095 ath10k-ct: update to version 2020-06-30
Backports commit "a1769bb68a850508a492e3674ab1e5e479b11254", which reverts
upstream commit "76d164f582150fd0259ec0fcbc485470bcd8033e" (ath10k: fix DMA
related firmware crashes on multiple devices).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-07-01 15:39:15 +02:00
Paul Spooren
263f7e5bbd build: store default/device packages in JSON
With this commit the `profiles.json` contain both the target specific
`default_packages` as well as the device specific `device_packages` as a
array of strings.

This information is required for downstream projects like the various
web-based interactive firmware generators.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-06-30 23:21:10 +01:00
Hans Dedecker
d4c80f5b17 dropbear: bump to 2020.80
- drop patches (applied upstream)
 * 001-backport_GNU_SOURCE-for-random.patch
 * 002-backport-move-GNU_SOURCE-earlier.patch
 * 010-backport-disable-toom-and-karatsuba.patch

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-06-30 22:13:46 +02:00
Rui Salvaterra
835c932ccb zram-swap: init: replace backticks with $()
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-30 19:03:15 +02:00
Rui Salvaterra
69ca308673 dropbear: init: replace backticks with $()
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-30 19:01:18 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
Kevin Darbyshire-Bryant
d59dc14515 kernel: cake: backport upstream tweaks & fixes
From upstream:
b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling
3f608f0c4136 sch_cake: fix a few style nits
8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed
9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally

From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags

The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically.  We fix it here just for cake.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 16:09:18 +01:00
Kevin Darbyshire-Bryant
77cd8f64ca kernel: cake: backport unused var patch to 5.4
This was backported to 4.19 and I clearly expected it to land in 5.4 but
it didn't (5.5) so backport it to 5.4 for consistency.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:24 +01:00
Kevin Darbyshire-Bryant
4ca4c94267 kernel: cake: skb hash backport to 419
Commit 7b4877c204 backported to 5.4 only,
backport to 4.19 as well.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:17 +01:00
Kevin Darbyshire-Bryant
3fda01a51e kernel: cake: renumber backport patches
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 09:34:06 +01:00
David Bauer
5667ccbf16 ramips: remove duplicate MAC assignment case
Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address
at the same position in flash.

Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 15:55:55 +02:00
David Bauer
1ba0466d43 package: add ravpower-mcu package
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:04 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
David Bauer
f49063ba92 ath79: replace custom uImageArcher generation
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.

Tested on: TP-Link Archer C59 v1

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:09 +02:00
Lars Wessels
dbaf0d20bb ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):

Device specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch

Flashing instructions (U-boot):

- Configure a TFTP server on your PC/Laptop and set its IP
  to 192.168.10.100

- Rename the OpenWrt image to firmware.bin and place it in the
  root folder of the TFTP server

- Power off (using the small sliding power switch on the left
  side) the device and connect an ethernet cable from its LAN
  or WAN port to your PC/Laptop

- Press the WPS button (and keep it pressed)

- Power on the device (using the small power switch)

- After a few seconds, when the WAN/LAN LED stops blinking
  very fast, release the WPS button

- Flashing OpenWrt takes less than a minute, system will
  reboot automatically

- After reboot the WPS LED will indicate the current OpenWrt
  running status

Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:01 +02:00
Adrian Schmutzler
5234593462 mvebu: move definition of factory.img out of Device/Default
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:57 +02:00
Adrian Schmutzler
0127de9547 ipq806x: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.

Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:50 +02:00
Adrian Schmutzler
e8afeaabc0 ipq40xx: set IMAGES in Device/Default definition
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.

Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 14:07:43 +02:00
Sungbo Eo
7da3c3b491 firmware-utils: sort tools alphabetically
Also remove leading whitespace after comma.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-06-28 02:27:36 +02:00
Adrian Schmutzler
8819faff47 ath79: do not build TP-Link tiny images by default
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.

Disable these images for the buildbots and prevent useless builds.

Note that these devices still build fine with default settings,
even for kernel 5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:33:44 +02:00
Adrian Schmutzler
89bb4ee450 mvebu: remove non-existant board name solidrun,clearfog-a1
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.

The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1

Fixes: 12795ec9f1 ("mvebu: split interface configuration for
clearfog pro and base")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:32:29 +02:00
Leon M. George
9f261e36de ath79: build Compex WPJ531 cpximg files
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).

Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Leon M. George
e10dd48360 ath79: add support for Compex WPJ531 (16M)
Specifications:

SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header

Installation:

To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).

Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.

For example, if the board is labelled '7A04':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin

MAC addresses:

<&uboot 0x2e010>  *:cb  (label)
<&uboot 0x2e018>  *:cc
<&uboot 0x2e020>  *:cd
<&uboot 0x2e028>  *:ce

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-28 00:26:39 +02:00
Hauke Mehrtens
143c81716d uboot-kirkwood: Revert "uboot-kirkwood: enable sata in nsa310 uboot"
This reverts commit 930f3c0148.

The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-06-27 18:39:32 +02:00
Jan Hoffmann
b1d5ab1a69 ramips: add support for NETGEAR WAC124
The WAC124 hardware appears to be identical to R6260/R6350/R6850.

SoC:   MediaTek MT7621AT
RAM:   128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI:  MediaTek MT7603 bgn 2T2R
       MediaTek MT7615 nac 4T4R
ETH:   SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB:   1x USB 2.0
BTN:   Reset, WPS
LED:   Power, Internet, WiFi, USB (all green)

Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2020-06-27 00:33:29 +02:00
Alex Lewontin
bd49f2c984 ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.

The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-27 00:29:45 +02:00
Javier Marcet
caf09f2b84 kernel: rename CONFIG_NETPRIO_CGROUP to CONFIG_CGROUP_NET_PRIO
This has been changed in kernel 3.14.

Signed-off-by: Javier Marcet <javier@marcet.info>
2020-06-27 00:19:13 +02:00
Hauke Mehrtens
4c3b81b75d ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGES
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
2020-06-27 00:19:13 +02:00
Daniel González Cabanelas
0cca96284a mvebu: LS421DE: dts file improvements
- Delete useless HDD presence inputs: they aren't buttons, and probably
  they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
  the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-27 00:19:13 +02:00
Aleksander Jan Bajkowski
58a6f06978 lantiq: remove unused PHY drivers on xrx200
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.

Save 20.3 kB flash memory.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-27 00:19:13 +02:00
Qin Wei
cd6515c2e8 ramips: fix sd polling
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.

Signed-off-by: Qin Wei <support@vocore.io>
2020-06-27 00:19:13 +02:00
Scott Roberts
dd13add3ce kernel: i2c-pxa: remove slave
Removing i2c pxa slave

The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.

Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2020-06-27 00:19:13 +02:00
Sukru Senli
c856f7adfb netifd: replace timesvr with timesrv
/lib/netifd/dhcp.script:
         Keep support for 'timesvr' while also supporting 'timesrv'
         Add log message indicating deprecation of 'timesvr'

Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
2020-06-27 00:19:13 +02:00
Alberto Bursi
930f3c0148 uboot-kirkwood: enable sata in nsa310 uboot
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.

Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-06-27 00:19:13 +02:00
Rogan Dawes
9c85153b87 sunxi: add text referencing Allwinner H3 and H5 CPUs
This makes it a little easier to figure out which options to choose.

Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
2020-06-27 00:19:13 +02:00
Huangbin Zhan
fed9bfbfeb base-files: coreutil-sha256sum breaks status code
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
	different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
	'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2020-06-27 00:19:13 +02:00
Gregory L. Dietsche
f3cb1636ab x86: Support Intel 10 Gigabit Ethernet Cards
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.

Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
2020-06-27 00:19:05 +02:00
Huangbin Zhan
3d6ac4d20f ubox: add ALTERNATIVES
This avoids a conflict with the kmod util from the package feed.

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2020-06-26 23:48:51 +02:00
Huangbin Zhan
67575b6410 logger: enable alternatives support
Avoid conflict with busybox

Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
2020-06-26 20:54:53 +02:00
Florian Eckert
5596452cd4 target/hack-5.4: platform/x86/pcengines: revert led simswich compromise
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00
Florian Eckert
f3c5c09e5a kernel: add pcengines-apu2 module description
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00
Florian Eckert
97bc87d81a kernel: add gpio-amd-fch module description
Add a module description for the new gpio-amd-fch device driver.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00
Florian Eckert
2b550a6be1 kernel/leds-apu2: remove deprecated leds-apu2 driver
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2020-06-26 20:54:53 +02:00