Some symbols are outdated or missing due to daily kernel bumps. It's
better to re-add them. All configs are automatically refreshed by
'make kernel_oldconfig CONFIG_TARGET=taget' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Remove stale sites from @GNOME alias:
* remove 2 sites that have stale 3 years old content
* remove 2 sites that have dropped GNOME
* convert 2 sites from FTP to HTTP
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
When a dependency is pulled in via conditional depends, and the condition
is already selected earlier in the chain, drop the condition.
This avoids some corner cases that trigger recursive dependencies.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 6c3eff9dd8.
This appears to cause some regressions in generated config.
Will be replaced with a fixed version later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a package foo depends on PACKAGE_foo:bar (in order to make build
dependencies conditional), tracking transitive dependencies can fail because
the internal seen flag is checked/set before eliminating the fake conditional
dependency. This can show up as a depends on not properly turned into a
select further down in the dependency chain
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Relocating the device tree is required for being apply to apply
device tree overylay at boot.
Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.
For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.
These are not related to the main vfio use case
(passthrough of PCIe devices)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.49
All no patches automatically rebased, just update to checksum for new version.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes from version 4.2.0 to version 4.2.1:
- Bug fixes (see <https://www.mpfr.org/mpfr-4.2.0/#fixed> and/or the
ChangeLog file).
- Improved MPFR manual.
- Configure tests: replaced the test of the link with GMP, in order to
avoid the use of a function without a prototype (Autoconf issue), as
this is obsolescent in ISO C. The new test should be more robust.
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
