On systems using brmcfmac (e.g. Raspberry Pi Zero W) without this fix,
the final setup-call:
iw dev wlan0 ibss join ...
fails with returncode 161 and message:
"command failed: Not supported (-95)"
So this patch calls an explicit:
iw dev wlan0 set type ibss
just prior to the 'ibss join' command.
I have tested several ath9k and mt76xx devices
with different revisions: this patch does not harm.
please also apply to stable branch.
Signed-off-by: Bastian Bittorf <bb@npl.de>
(cherry-picked from commit ea5fce3f46)
In some cases, spurious failures might be cleared by teardown and retry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 42dda0ed3e)
The channel offset used for VHT segment calculation was missing for HT
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit a0d81ba0d5)
Use it to look up frequencies only in the configured band to better deal
with channel number overlap
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 8b8c1cb09b)
drv_mac80211_teardown fails silently if the device to be torn down is
not defined. This commit prints an error message.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
(cherry-picked from commit 3933e29d1b)
When wifi is turned off, drv_mac80211_teardown sometimes fails (silently)
because the device to be torn down is not defined.
This situation arises if drv_mac80211_setup was called twice when
wifi was turned on.
This commit ensures that the device to be torn down is always defined
in drv_mac80211_teardown.
Steps to reproduce:
1) Use /sbin/wifi to turn on wifi.
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
2) Use /sbin/wifi to turn off wifi.
uci set wireless.@wifi-device[0].disabled=1
uci commit
wifi
3) Observe that wifi is still up.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
(cherry-picked from commit d515f6b6cd)
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete. But
"ubus call network.wireless status" erroneously reports that radio0 is down.)
The relevant part of drv_mac80211_setup is,
if [ "$no_reload" != "0" ]; then
add_ap=1
ubus wait_for hostapd
local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")"
ret="$?"
[ "$ret" != 0 -o -z "$hostapd_res" ] && {
wireless_setup_failed HOSTAPD_START_FAILED
return
}
wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1
fi
This commit sets no_reload = 0 during the second call of drv_mac80211_setup.
It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.
When /sbin/wifi is used to turn on wifi,
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
/sbin/wifi makes the following ubus calls,
ubus call network reload
ubus call network.wireless down
ubus call network.wireless up
The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,
drv_mac80211_setup
wireless_device_setup_cancel
drv_mac80211_setup
In contrast, when LuCI is used to turn on wifi only a single call
is made to drv_mac80211_setup.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
(cherry-picked from commit a29ab3b79a)
Testing with hwsim reveals two problems:
1. phyX/addresses has two addresses and mac80211_get_addr keeps
returning the last one when asked for more;
2. The base address has the local bit set and the operation unsets it.
Fix both.
Fixes: 866790fd82
Reported-by: Zero_Chaos
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
If mac80211_setup_supplicant() is called with enabled=0 then it should just
destroy the interface and remove the configuration from wpa_supplicant. But
the ubus method call always returned
Command failed: Method not found
because the actual name of the method is "config_remove".
Fixes: b5516603dd ("mac80211: more wifi reconf related fixes")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[bump PKG_RELEASE]
Signed-off-by: David Bauer <mail@david-bauer.net>
hostapd_set_bss_options expects the PHY as second and the VIF as third
argument. However, only the VIF was passed as second argument without a
third argument at all.
This was never a problem, as both PHY and VIF were never accessed.
However, with FTM support the PHY is needed to determine the HW support
when configuring the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is useful to bring up multiple client mode interfaces on a single
channel much faster without having to scan through a lot of channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't kill the wireless daemon on teardown. hostapd as well as
wpa_supplicant are managed by procd which would detect the shutdown of
either process as a crash loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently a device which has a DFS channel selected using the UCI
channel setting might switch to a non-DFS channel in case no chanlist is
provided (UCI setting "channels") when the radio detects a DFS event.
Automatically add a chanlist consisting of the configured channel when
the device does not operate in auto-channel mode and no chanlist set to
circumvent this issue.
Signed-off-by: David Bauer <mail@david-bauer.net>
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168c ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
The user can now enable the ACK timeout estimation algorithm (dynack)
for drivers that support it.
It is also expected that the distance config accepts the same values as:
$ iw phyX set distance XXX
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
* uci state was not getting reset properly during teardown
* AP+STA co-exist state was not flushed properly upon channel switch
* remove a debug logger call
* properly teardown supplicant instances when they get disabled
* add md5 config support for supplicant
* don't call wpa_supplicant_prepare_interface twice
Signed-off-by: John Crispin <john@phrozen.org>
Some FullMAC cfg80211 wireless devices do not support virtual
interfaces, hence there is script logic to keep the existing network
device. Improve this to support renaming the interface if needed and
make sure the existing interface actually belongs to the right phy.
Change calls to 'iw' to avoid outputing warnings and errors to not
confuse users of such devices.
Also bump PKG_RELEASE which has been forgotten in the previous two
mac80211 changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of using the actual interface name, a hard-coded 'wlan0' has
slipped into the script. Replace it.
Fixes: ccf2aa9d4b ("mac80211: detect existing interface before adding")
Reported-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
hostapd allows putting WDS (4addr mode) clients into a separate bridge
other than the bridge regular (3addr mode) clients end up in. This is
useful for example giving WDS clients access to several VLANs
(trunking) while regular clients will end up inside a specific VLAN.
Add 'wds_bridge' config parameter for wifi-iface which contains the
name of the bridge. hostapd-mini already supports this feature, so all
needed is to add the UCI wrapping in mac80211.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Network interfaces are looked up based on the device behind a phy, so the
phy needs to be checked separately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, txpower for the PHY is applied when configuring the PHY
instead of the VIF. Otherwise, the configured txpower is not applied for
the first initialized VIF when using DFS channels, as it is currently
applied too early when the CAC hasn't finished.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
If no AP is configured, hostapd-${phy}.conf is not being created,
hence md5sum fails and causes log pollution:
netifd: radio1 (3183): md5sum: can't open '/var/run/hostapd-phy1.conf': No such file or directoy
Hence make sure the file exists when calling md5sum.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before commit 60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In addition to wpa_supplicant and hostapd managed interfaces, also
track unmanaged interfaces. This is used to make sure that running
'wifi' always returns into a clean state regardless of what the user
did before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This also fixes mac80211_prepare_vif iw set channel in monitor or
mesh mode.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed commit message]
Commit b3d8b3a introduced a new test:
[ -n "$noscan" -a "$noscan" -gt 0 ] && hostapd_noscan=1
But if length of "$noscan" is zero (noscan is not set) this doesn't stop
the shell to evaluate the rest of the test.
root@hank2:~# [ -n "$noscan" -a "$noscan" -gt 0 ]
ash: out of range
root@hank2:~#
So when radios are brought up this shows in the log:
Sat Nov 23 10:51:38 2019 daemon.info procd: - init complete -
Sat Nov 23 10:52:24 2019 daemon.notice netifd: radio1 (1243): sh: out of range
Sat Nov 23 10:52:25 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sat Nov 23 10:52:25 2019 daemon.notice netifd: radio0 (1242): sh: out of range
Sat Nov 23 10:52:26 2019 authpriv.info dropbear[1536]: Not backgrounding
This commit sets noscan to 0 if unset and removes the gratuitous length
check, preventing the warning.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Keep existing wdev when creating new nl80211 interfaces if phy and
type match, delete it otherwise.
To make this work, also remove left-over debugging function which
prevented the return-value of the 'iw' command to be taken into
account in mac80211_iw_interface_add().
As 4addr-mode (WDS) was setup during interface creation for station
interfaces, also set it after interface creation to make sure an
existing sta interface ends up with the right mode.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
