The sysupgrade formware of the Puzzle series is a slightly strange
dual-boot approach while remaining compatible with Marvell's SDK
firmware upgrade binary format -- which happens to be a full-disk
image with GPT partition table. Hence that /lib/upgrade/emmc-puzzle.sh
script is like an exotic disease which results from those decisions,
and as we also want to somehow stay compatible with the IEI-World
stock firmware we got to use it in that same way (we are not
compatible with the QNAP-branded identical hardware device anyway).
Currently, on sysupgrade the result is that one ends up with the old
content of rootfs_data (a GPT partition on those devices) as nothing
ever wipes or in any way re-creates the filesystem there. As a simple
work-around, let's kill the filesystem on rootfs_data so fstools
re-formats it on the next boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d4e8653e1e)
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc177695e0)
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d546b3b4c)
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit eac1928430)
This has been a part of modified upstream patch but got lost on major
kernel bump to 5.15, so bring it back.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Add patch for kernel 6.1 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5e6bab661a)
1. Add new symbols to generic config
2. Bump kernel
Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit daed3322d3)
Backport Russell King's series [1]
net: mvneta: reduce size of TSO header allocation
to pending-5.15 to fix random crashes on Turris Omnia.
This also backports two patches that are dependencies to this series:
net: mvneta: Delete unused variable
net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
[1] https://lore.kernel.org/netdev/ZCsbJ4nG+So%2Fn9qY@shell.armlinux.org.uk/
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (squashed)
(cherry picked from commit 7b31c2e9ed)
Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.
1000 Mbps: Green
100 Mbps : Amber
10 Mbps : (turn off)
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use <mdio>:<addr>:<speed> trigger for LEDs, enable PHY LED trigger
(CONFIG_LED_TRIGGER_PHY).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Avoid MCU getting "command reply receive timed out" message when LED
configuration setting trigger function is enabled in heartbeat mode.
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for mvebu/cortexa9 devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-50E and interrupt to show bootmenu
2. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
3. Prepare TFTP server with the parameters obtained above
4. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
6. Type "r" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
7. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
7. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
8. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of
WAN1/2 are connected to GPIO expander. There is no way to indicate
link speed of networking device on Linux Kernel/OpenWrt, so those LEDs
cannot be handled like stock firmware.
On OpenWrt, use netdev(link) trigger instead.
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:7D
WAN 2 : 70:4C:A5:xx:xx:7E
LAN 1 : 70:4C:A5:xx:xx:7F
LAN 2 : 70:4C:A5:xx:xx:80
LAN 3 : 70:4C:A5:xx:xx:81
LAN 4 : 70:4C:A5:xx:xx:82
LAN 5 : 70:4C:A5:xx:xx:83
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370
Hardware:
SoC: Marvell Armada 88F6707
CPU: Cortex-A9 800 MHz, 1 core
Flash 1: SPI-NOR 1 MiB (U-Boot)
Flash 2: NAND 512 MiB (OS)
RAM: DDR3 256 MiB
Ethernet: 1x 1GbE
USB: 1x 2.0
SATA: 2x 3Gb/s
LEDs/Input: 5x / 2x (1x button, 1x slide-switch)
Fan: 1x casing
Flash instructions, from hard drive:
1. Get access to the "boot" partition at the hard drive where the stock
firmware is installed. It can be done with acp-commander or by
plugging the hard drive to a computer.
2. Backup the stock uImage:
mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
3. Move and rename the Openwrt initramfs image to the boot partition:
mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
4. Power on the Linkstation with the hardrive inside. Now Openwrt will
boot, but still not installed.
5. Connect via ssh to OpenWrt:
ssh root@192.168.1.1
6. Rename boot files inside boot partition
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
ubiformat /dev/mtd0 -y
ubidetach -p /dev/mtd1
ubiformat /dev/mtd1 -y
8. Flash the sysupgrade image:
sysupgrade -n openwrt-squashfs-sysupgrade.bin
9. Wait until it finish, the device will reboot with OpenWrt installed
on the NAND flash.
Restore the stock firmware:
1. Take the hard drive used for the installation and restore boot backup
files to their original names:
mount -t ext3 /dev/sda1 /mnt
mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
2. Boot from the hard drive and perform a stock firmware update using
the Buffalo utility. The NAND will be restored to the original
state.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Assign fan with 4 active cooling levels to be used for the main CPU as
well as external SerDes units.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Several fixes for the Puzzle WT61P803 hwmon driver were needed to make
it behave well as thermal cooling device:
- wire-up cooling device with OF node in device tree
- properly parse cooling-levels (u32 with range check vs. u8)
- actually use cooling-levels
- keep current state and only write to uC if state has changed
(avoids flooding the uC with commands which will result in uC crashing)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
shellcheck warns against it with SC2086. It also hides a bug that
shellcheck marks with SC2015. Fixed those with explicit if/else.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of using the shell's evaluation, use grep's -q parameter.
Found with shellcheck's SC2143.
Also replaced a head call with grep's -m.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Due to upstream change in U-boot the binaries were renamed [1].
[1] 87ac4b4b4c
Fixes: 2f83369e3e ("uboot-mvebu: update to version 2023.01")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Upstream commit [1] included in the Linux kernel version 6.2 was
backported to Linux kernels 6.1.4, 6.0.18. It should be possible that it
is going to be backported even to the 5.15 series, but before it happens,
let's include it here.
It was discovered that on SOC Marvell Armada 3720, which is using e.g.
Turris MOX, and if you are also using it with older ARM Trusted Firmware
v1.5, it is not possible to detect connected USB 3.0 devices, but they
are working just fine when connected with USB 2.0 cable. This patch
fixes it.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/drivers/phy/marvell/phy-mvebu-a3700-comphy.c?id=b01d622d76134e9401970ffd3fbbb9a7051f976a
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Michal Hrusecky <michal.hrusecky@turris.com>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[improve commit description, added tag to the patch]
The GL-MV1000 ships with a 16MB spi-nor flash, containing a copy of the stock GL.iNet firmware.
Add the corresponding flash areas, so our view matches the one of the in-flash stock firmware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Removed upstreamed:
pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2]
bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3]
Manually rebased:
ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4]
Added patch/backported:
ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)
Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match. I opted to delete that
file.
5. Suggestion by hauke: 19098934f9
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."
Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
This reverts commit 97c77fff28 as commit
8be6350f66 ("generic: 5.15: allow MV88E6xxx built-in when PTP support
disabled") contains the fix, so lets enable kernel 5.15 on mvebu again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 5429411f73 as upstream
in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has
changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel.
That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.
References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.
Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
