Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As per the series:
<https://www.spinics.net/lists/devicetree/msg508906.html>
"Enforce specific naming pattern for children (keys) to narrow the
pattern thus do not match other properties. This will require all
children to be properly prefixed or suffixed (button, event, switch
or key)."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This makes it possible to fix Netgear WNDAP620+660 DTS ugliness.
Bring back the dtb and firmware partitions for the WNDR4700.
Thank you, mans0n.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
in order to get nvmem-cells to work on AP and routers
(Netgears WNDR4700). The nvmem-cell needs to be within
a fixed-partition dt-node.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
- dropped the deprecated, but beloved "label" property.
- rename all DT leds node names to led-#.
- add function and color properties.
- utilized panic-indicator property.
- dropped led- aliases (see below).
migration scripts for all devices are included.
For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>
For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.
... While at it: also do some cleanups in the DTS in there.
The original (re-)installation described in
commit d82d84694e ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
# tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
# bootm
However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- remove stray #address-cells / #size-cells
- fix partition unit-addresses in wd-mybooklive.dts
- remove index from MBL's gpio node name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
