Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
This breaks the package builds using the SDK.
The targets all build fine, but the package builder fails on many
packages. The package builder uses the OpenWrt SDK.
This reverts commit c377d874be.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates libtool to its current release, from 2015. Current patches
were renumbered and given a description text. The fix in
160-passthrough-ssp.patch is no longer needed.
A patch to speed up build was cherry-picked, and another openwrt
specific patch was needed to not use quotes in $(SHELL), to acommodate
our "SHELL=/usr/bin/env bash" usage.
The already present call to ./bootstrap ensures that generated files are
refreshed, so the patches are applied only to their sources. Also, that
bootstrap call was adjusted to run at the appropriate time when QUILT=1.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
meson is a next generation build system designed to have good defaults,
simpler build files, and fast compilation.
It is built upon python and uses ninja for compilation. The latter
provides fast by default (parallel) and problem free compilation.
There are over 40 packages already successfully using meson. The next
commit will convert pkgconf to use meson compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
ccaaab1c04 says that this is in the
codebase because of libsigc++, which is not in the codebase anymore.
Neither in base nor in packages. It doesn't seem to be needed by
anything else either. GNOME packages have transitioned to using meson,
which does not use m4 files.
Tested local compile with CONFIG_ALL. No problems seen.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Starting with v3 of the vendor firmware for the TP-Link EAP235-Wall v1,
downgrades to firmware versions below v3 as not allowed. Since OpenWrt
uses version 0.0.0 as a default, this causes the factory install to fail
on devices with a recent firmware. This failure is associated by the
following message on the device's serial console:
EAP235/230-Wall forbid fw reverted from 3.x.x to lower version!
Vendor firmware (v3) also uses build and release numbers to compare
images, so identical version numbers are very unlikely to cause issues.
Bump the firmware version to 3.0.0 to ensure users can install OpenWrt
on their devices.
Reported-by: Colton Conor <colton.conor@gmail.com>
Tested-by: Colton Conor <colton.conor@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some devices using the safeloader firmware format require a minimum or
specific version to be set in the soft-version metadata partition.
Currently only custom text values can be provided, but not all device
firmware support this format.
Modify the device info struct to allow for more well-defined types of
soft-version overwrites, and provide a few macros for easy value
initialisation. Requires all existing values to be updated to match the
new structure.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
[Adapt TL-WA1201-V2 entry too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The structured soft-version partition has a field which contains a
(source) revision number. Factory images used to include this, but
it was accidentaly removed during an earlier refactoring.
Include the source revision number again in the generated soft-version
partition. Additionaly, also show this revision number when printing
image info.
Fixes: 1a211af2cb ("firmware-utils: tplink-safeloader: refactor meta-partition generation")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This was missed because scancode license scanner was confused by a
slightly different than expected license text (96,75% license score).
License text included "file" instead of "library" in the main part of
the licensing info. It also used "The GNU C Library" instead of the
standard "This library" in 2nd and 3rd paragraphs.
The first paragraph clearly mentions LGPL-2.1-or-later and the use of
"file" instead of "library" should not affect licensing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is a wireless access point working on the 2.4 GHz and 5 GHz
band, based on Qualcomm/Atheros QCA9563 + QCA9886.
Specification
- 775 MHz CPU
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- QCA9563: 2.4 GHz 3x3
- QCA9886: 5 GHz
- AR8033: 1x 1 Gbs Ethernet
- 4x LED, WPS factory reset and power button
- bare UART on PCB (accessible through testpoints)
Methods for Flashing:
- Apply factory image in OEM firmware web-gui. Wait a minute after the
progress bar completes and restart the device.
- Sysupgrade on top of existing OpenWRT image
- Solder wires onto UART testpoints and attach a terminal.
Boot the device and press enter to enter u-boot's menu. Then issue the
following commands
1. setenv serverip your-server-ip
setenv ipaddr your-device-ip
2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in
hex, henceforth "sizeinhex")
3. erase 0x9f030000 +"sizeinhex"
4. cp.b 0x80060000 0x9f030000 0x"sizeinhex"
5. reboot
Recover:
- U-boot serial console
Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch>
[convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
mkmerakifw-old was created for the z1 which uses the AR9344 SoC with
be32 addressing. The MX64/MX65 devices use the same header style, however
these boards use a BCM NSP SoC with le32 addressing.
Since we may be booting initramfs images with this header, which may be
of any size, within reason, board->imagelen is set to 0. The kernel
image shoule be limited in the image Makefile.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was missed because scancode license scanner was confused by
comments about crc32buf().
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Gabor Juhos <juhosg@freemail.hu>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was missed because scancode license scanner was confused by a
comment about (no) copyrights in the init_crc_table().
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Gabor Juhos <juhosg@freemail.hu>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was missed because scancode license scanner was confused by a
comment about Cisco's GPL code github repository.
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
This uses "GPL-2.0-or-later" header for files identified using scancode
license scanner with 100% score as GPL 2.0 or later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifications:
SOC: Qualcomm Atheros TP9343 (750 MHz)
Flash: 8 Mb (GigaDevice GD25Q64CSIG)
RAM: 64 Mb (Zentel A3R12E40DBF-8E)
Serial: yes, 4-pin header
Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA
3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L
Ethernet: Qualcomm Atheros TP9343
Lan speed: 100M ports: 4
Lan speed: 100M ports: 1
Other info: same case, ram and flash that TP-Link TL-WR841HP,
different SOC
https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/
Label MAC addresses based on vendor firmware:
LAN *:ee label
WAN *:ef label +1
WLAN *:ee label
The label MAC address found in "config" partition at 0x8
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com>
[remove various whitespace issues, squash commits, use short 0x0]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Compile with Ninja. Ninja compiles faster and is more stable with
parallel builds. Routines copied from cmake.mk.
Speed improves from:
Executed in 127.47 secs fish external
usr time 17.02 mins 446.00 micros 17.02 mins
sys time 1.18 mins 40.00 micros 1.18 mins
to:
Executed in 118.91 secs fish external
usr time 17.28 mins 499.00 micros 17.28 mins
sys time 1.13 mins 45.00 micros 1.13 mins
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The Canadian edition of the TP-Link Archer A6 v3 uses a different header, but
otherwise it's identical to the already supported EU/US editions.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Brian Lee <dev@leebrian.me>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
