The Build prefix is used for image build commands, while the Device
prefix should be used for base recipes for devices. Apply the same
naming convention here.
While touching the file, also fix the mixed indentation.
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
There seems to be no reason to have the Netgear switches as part of
the main Makefile. Move it to its subtarget-specific Makefile since
it is only applicable there.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[update commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently supported HPE 1920 devices all have an RTL838x SoC, but there
are larger switches with RTL839x SoCs, although currently not supported.
Move the build recipe to common.mk so the larger devices can also make
use of the recipe, while moving it out of the main Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The D-Link DGS-1210 device series currently has supported devices with
both RTL838x and RTL839x SoCs. An image build recipe has been defined in
both subtarget makefiles, but these are mostly identical, save for the
SOC variable.
Move the SOC variable from the DGS-1210 build recipes to the applicable
devices, and put the remaining duplicate code in a shared Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specification
----------------------
* RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz
* 128MB DRAM
* 32MB NOR Flash
* 48 x 10/100/1000BASE-T ports
- 6 x External PHY with 8 ports (RTL8218D)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14
The gpio-restart node is not required but it does reset the switch.
TODO: The 4 combo ports attached to the RTL8214FC are not detect
properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES"
and 51 and 52 as "RTL8218B (external)". Those ports only work if
u-boot initialize it (for example, loading initramfs image using one
of those ports). A patch to PHY detection is needed for full support.
The firmware recovery using U-Boot is broken for all DGS-1210 tested
devices as pressing RESET does not trigger it (only if pressed from a
running stock image)
UART pinout
-----------
[o]ooo|J14
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM upgrade
------------------------------
1. Make sure you are running OEM firmware in image2 slot (logged as admin):
- > config firmware image_id 2 boot_up
- > reboot
2. Install squashfs-factory_image1.bin to image1 using (logged as admin):
- > download firmware_fromTFTP <tftpserver> factory_image1.bin
- > config firmware image_id 1 boot_up
- > reboot
Installation using serial interface
-----------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
Once booted the initramfs, install the squashfs-sysupgrade.bin as a
normal OpenWrt system.
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / boot image 1 (CLI as admin):
- > config firmware image_id 1 boot_up
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000'
- # fw_setenv image '/dev/mtdblock7'
- # reboot
Debrick using serial interface
------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
Back to stock firmware using dual-boot
--------------------------------------
If you have serial interface, you can change u-boot env vars
interrupting the boot process. If not but you are running OpenWrt, you
can dual-boot (as mentioned eariler) and skip to step 4:
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Boot the image 2:
- set image /dev/mtdblock7; run addargs; bootm 0xb4e80000
4. Once booted, log as admin and change the boot image to 2
- > config firmware image_id 2 boot_up
- > reboot
5. After the boot, flash image1 with the vendor image
Back to stock firmware using DNA
--------------------------------
1. From an OpenWrt:
- # fw_setenv bootstop on
- # reboot
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
It has been developed and tested on device with F3 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The D-Link DGS device tree was reorganized to better reflect the common
DT parts. The common include is named SOC specific (838X) and it seemed
like a good choice to add another common include in the future for the
RTL839X devices. From the current point of view this option is not really
needed.
1. The common part only includes data that matches RTL839X devices too.
2. The Panasonic DT structure avoids including the basic DTSI inside the
common DTSI.
Taking simplicity of the Panasonic include logic and in perparation to
provide DGS-1210-52 support it makes sense to harmonize this.
- rename common include to reflect its content
- move the link to the root DTSI directly to the device specific DTS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.
Fixes: 675cf75578 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c33 ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c25 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da8669 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently factory.bin image recipe of ASUS RP-AC51 is not specified
explicitly and is thus set to the leaked one from the device recipe
right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage.
Fixes: 416d4483e8 ("ath79: add support for ASUS RP-AC51")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The 'fxload' tool contained in the examples provided with libusb is
actually useful and turns out to be the only way to load firmware into
some rather ancient EZ-USB microcontrollers made by Cypress (formerly
Anchor Chips).
The original 'fxload' tool from hotplug-linux has been abandonned long
ago and requires usbfs to be mounted in /proc/bus/usb/ (like it was in
Linux 2.4...).
Hence the best option is to package the modern 'fxload' from the libusb
examples which (unsurprisingly) uses libusb and works on modern
systems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
21360a1b1ce6 cli: fix typo
abfebece0af1 wg-linux: ship a copy of linux/wireguard.h
1cbb1a543cb3 pex: reduce unnecessary ping traffic
0c2f39e52d5d pex: remove pex event debug spam
dcf1362c2104 pex: add support for sending/receiving global PEX messages via unix socket
df5f70b8858c ubus: notify on network updates
e58a56697131 add DHT discovery service
be175767bc67 pex: keep active pex hosts after the specified timeout
543e4a3d2ed7 pex: move rx header check to callback function
395659b9c415 pex: move raw ip send code to sendto_rawudp() in utils.c
dda15ea8b3b2 pex: add utility function to get the sockets based on type / address family
e88f2cd4d3f0 utils: add support for passings address family to network_get_endpoint()
639cdcdf6eda pex: add support for figuring out the external data port via STUN servers
9144339ebe1f pex: improve handling of a longer list of PEX hosts
38212218ecdd unet-cli: add DHT support
0d37ca75434d pex: automatically create host entries from incoming endpoint port notifications
035fcc56ef60 host: keep multiple endpoint candidates, one for each type
a089e8ae7504 pex: avoid sending a query to a host more than once every 15 seconds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
libwolfssl-cpu-crypto is a variant of libwolfssl with support for
cryptographic CPU instructions on x86_64 and aarch64.
On aarch64, wolfSSL does not perform run-time detection, so the library
will crash when the AES functions are called. A preinst script attempts
to check for support by querying /proc/cpuinfo, if installed in a
running system. When building an image, the script will check the
DISTRIB_TARGET value in /etc/openwrt_release, and will abort
installation if target is bcm27xx.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
cc4eb79 ubus: support obtaining numeric error code
01c412c ubus: add toplevel constants for ubus status codes
8e240fa ubus: allow object method call handlers to return a numeric status code
5cdddd3 lib: add limit support to split() and replace()
0ba9c3e fs: add optional third permission argument to fs.open()
c1f7b3b lib: remove fixed capture group limit in match() and regex replace()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch will print the name of the modem in the bootlog
during probing.
This allows to verify that the exact model was loaded and not some
generic type.
The only other way to do this is by enabling dynamic debugging
which is disabled by default in OpenWRT
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to an oversight we accidentally inverted the timeout check. This
patch corrects this.
Fixes: 9cec4a0ea4 ("realtek: Use built-in functionality for timeout loop")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[ wrap poll_timeout line to 80 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- refresh config
- disable suspend as it's pointless in the sope of OpenWrt
- enable CPU frequency scaling
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
In commit 81e3017609 ("realtek: clean up rtl838x MDIO busy wait loop")
a hand-crafted loop was created, that nearly exactly replicate the
iopoll's `read_poll_timeout` functionality.
Use that instead.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Improve dl_cleanup by adding an option to also clean the build directory
related to the downloaded package.
The script will check every directory in build_dir/ and check if any
old package is present there. If outdated package are found, the old
one are cleared leaving only the last one.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Update the existing patch to use a shebang that works on systems that
don't have a /bin/bash, e.g. NixOS or GuixSD.
Signed-off-by: Ilya Katsnelson <me@0upti.me>
