Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The default strength is not enough to provide stable connection
under 3.3v LDO voltage.
Fixes: 32d5921b8b ("rockchip: add Orange Pi R1 Plus LTS support")
Fixes: #13117Fixes: #13759
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3399 ARM64 (6 cores)
4GB LPDDR3 RAM
1x 1000 Base-T
1 GPIO LED (status)
HDMI 2.0
3.5mm TRRS AV jack
Micro-SD slot
16GB eMMC
1x USB 3.0 Port
2x USB 2.0 Port
1x USB Type-C Port
1x M.2 PCI-E Port
AP6356S (BCM4356) SDIO WiFi & Bluetooth adapter
--------
Note: AP6356S is not supported yet due to the lack of firmware and NVRAM
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
