This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Since kernel 5.4 has been droppped from IPQ40xx, there is no need to keep
the version checks for kernels older than 5.10.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, suspend and resume ops are not present, this means that if user
disables a DSA interface that the PHY-s remain alive and the link is up.
Fix it by using generic PHY suspend and resume ops.
Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
There is no point in using a DT property to trigger setting the PSGMII
PHY AZ transmitting ability.
Especially since EEE can be disabled using ethtool anyway.
Fixup the mask for setting the workaround as only BIT(0) is actually being
changed and use the phy_clear_bits_mmd helper instead of reading, then
clearing the bit and writing back as it does everything for us.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, QCA807x doesnt do any kind of validation to see whether it
actually supports the inserted module.
So lets add checks to allow only 1000BaseX and 100BaseFX based modules.
While adding validation, move fiber configuration to insert/remove events
instead of always doing it at config time.
This allows getting rid of the DT property for fiber enable and now only
the upstream sfp phandle is required.
Since we are refactoring fiber related code, lets heavily simplify the
status polling as the current logic is overcomplicated due to previous
wish to support non standard SFP cages that dont have pins properly
connected, that is removed now and only proper SFP cages will work.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.
Without it using the pins as GPIO-s did not actually work.
Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.
Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.
This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.
This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.
These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
