This adds initial support for the A64 Allwinner SoC to LEDE.
It will be build in the new cortexa53 subtarget.
Currently it only supports the pine64 and the image is able to boot on
this SoC.
Camera, Ethernet, HDMI and other parts are currently not working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports some more patches from kernel 4.11 adding more devices
to the device tree of the A64 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports multiple patches from kernel 4.10 which are adding
missing support for the A64 and the pine64 board. These are the device
tree files, the pinctlk and the clock driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required to support kernel 4.9.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
[rewrite commit message (subject <= 50 characters)]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Delete a bunch of fixes that are already included.
Refresh patches.
Compile-tested on malta/mipsel
Runtime-tested on malta/mipsel
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
4.4.80+ contains 71a165f6397df07a06ce643de5c2dbae29bd3cfb, 4.9.41+ contains
6c78197e4a69c19e61dfe904fdc661b2aee8ec20 which are all backports of upstream
commit 0878fff1f42c18e448ab5b8b4f6a3eb32365b5b6 ("net: phy: Do not perform
software reset for Generic PHY").
Our local patch is no longer needed, all this patch was doing was utilizing
gen10g_soft_reset which does nothing either, so just keep the code unchanged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We will be prompted with this config symbol when performance monitoring is
enabled in the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The factory partition of the Phicomm K2P contains two MAC addresses.
The lower MAC address is at offset 0xe006 and the higher one is at
offset 0xe000.
Use the lower MAC address as base mac-address which the switch driver
increments by one for the second (wan) vlan.
The MAC addresses are still inverted in contrast to the stock firmware
where the lower MAC address is used for wan. But at least the use of a
MAC address not intended/reserved for this particular board is fixed.
Signed-off-by: Jiawei Wang <me@jwang.link>
In commit b11c51916c ("ramips: Improve Sanlinking D240 config") I made
a mistake with regards GPIO numbering. And in addition to specifying the
wrong GPIO for controling the power of one of the mini-PCIe, I recently
discovered that the power of both slots can be controlled.
This patch specifies the correct GPIO for the left-most mini-PCIe slot
of the D240 (labeled power_mpcie2 since the slot is attached to SIM2),
and adds a GPIO that can be used to control the power of the other
mini-PCIe slot (labeled power_mpcie1).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[do not use the gpio active macros for the gpio-export value]
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:
1) Using tftp mode with UART connection and original LEDE image
- Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
server directory
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, power up the router and press
key "4" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
setenv serverip 192.168.0.66
tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
- After that the device will reboot and boot to LEDE
2) Using tftp mode without UART connection but require some
manipulations with target image
- Download and unpack TP-Link Archer C20 v1 firmware from original web
site
- Split uboot.bin from original firmware by this command (example):
dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1
- Create ArcherC20V1_tp_recovery.bin using this command:
cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin
- Place ArcherC20V1_tp_recovery.bin in tftp server directory.
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
- Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.
The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.
Not tested:
* SD card reader.
Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The cns3xxx interrupt controller uses a single register and as such
the 'mask' reg/functions must be used as opposed to the 'enable'/'disable'
reg/functions.
This fixes an issue that occurs if more than one GPIO on a specific controller
(there is GPIOA and GPIOB each having 32 GPIO's) uses interrupts. When one
would get enabled all others would be disabled prior to this patch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes CVE-2017-11600.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
For the Archer C50v1, the EU and US versions are differentiated by their
respective HW additional version (0x0 for US, 0x2 for EU).
The stock web interface checks this field before flashing, making it
impossible to flash the current (US) factory image on EU hardware.
However the bootloader does not check this field, making it possible to use
a single sysupgrade image for both hardware.
This patch adds the necessary build bits to generate both EU and US factory
images, and renames the target as "Archer C50v1" since there are as of now
3 different versions of Archer C50 (all with different CPUs).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.
Not tested:
* SD card reader.
Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.
Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.
Based on a patch send by Martin Schiller.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 77645ffcd9 ("ramips: add support for the GnuBee Personal Cloud
One") dropped the execution permission from 01_leds with the result
that the file isn't started during first boot and no default LED
configuration is added.
Revert the introduced file permission change.
Fixes: FS#979
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[cherry picked the fix from a board support patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
mode when connected to 10M/100M ethernet.
Signed-off-by: Kuang Rufan <master@a1983.com.cn>
