DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.
This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There are few symbol changes but only 3 symbols were possible to set:
THERMAL_EMERGENCY_POWEROFF_DELAY_MS
CLK_BCM_SR
PHY_NS2_USB_DRD
Both new drivers don't seem to apply to Northstar so they are disabled.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Right patch version this time, sorry!
* Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code.
* Refreshed patches.
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).
Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx & oxnas.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.
Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Looking for a wrong LED file name was stopping this code from find any
LED. This affects devices with only a red/amber power LED.
Fixes: 3aaee1ba02 ("bcm53xx: failsafe support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since BusyBox 1.25.0 dd command supports iflag=skip_bytes which allows
skipping requested amount of bytes without reducing blocksize. Thanks to
this we can leave default blocksize and let dd work more efficiently.
On Netgear R6250 "dd skip=58 iflag=skip_bytes" can be 5 times faster
than "dd bs=58 skip=1" when extracting TRX out of CHK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
That patch fixes handling SPI messages with two writing transfers. It's
important when using e.g. by m25p80 driver which uses one transfer for
opcode and another one for data.
Thanks to that fix we can now drop m25p80 workaround patch. It means one
less hack and also a better flash writing performance as there is no
more data buf copying.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The advantage is that we don't have to specify max TRX size anymore and
otrx doesn't allocate a buffer of that size. It saves us allocating
32 MiB for every image we generate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches.
Compile-tested on ramips/mt7621 and x86/64.
Runtime-tested on ramips/mt7621 and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:
473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed
403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0
180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item
Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)
Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This model also contains few partitions non-discoverable partitions we
need to "protect". Othen than that it uses non-deprecated serial entry
in DTS that doesn't work with LEDE so we need to workaround it as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Many (most?) devices can't boot raw kernel using tftp and probably none
allows flashing it. It's way more usable to have TRX with kernel
containing initrams as such an image can be actually flashed.
An exception are Buffalo devices which have recovery mode with support
for booting kernels over TFTP. For them keep building default images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for describing GPIO chips placed on PCIe cards. Thanks
to this we get working 2.4 GHz LED on Tenda AC9.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes GIC interrupts (required before switching to 4.9), adds few
new entires & introduces DTS for Archer C5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This driver has been added instead of improving spi-bcm53xx. It has some
advantages: allows SPI speed control & hopefully doesn't have bug that
was stopping us from using multiple SPI messages for writing flash data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.
There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver
After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's needed for macaddr_add.
Fixes: 50efd403e6 ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In kernel 4.9 it's already present so we don't want to overwite it (with
older & API incompatible version).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
only factory images for DHP-EU and DHP2-JP (fw ver. 2.x) are built.
this will not work for DHP-JP/AP/TW (fw ver. 1.x) because they use
different buffalo_csum() formula.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This device has 2 TRX partitions (main one and failsafe one) and Linux
may not detect them properly failing to run userspace.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This specifies wireless limitations for Netgear R8000 making sure people
won't use channels incorrectly (limited performance). There are also 2
new DTS files not used by us yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
We don't use this driver since commit 741715331a ("bcm53xx: switch to
m25p80 and drop bcm53xxspiflash").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There are many targets using user space scripts to generate firmware but
bcm53xx doesn't need this, so let's disable that kernel option.
This lets us avoid some scary-looking kernel warnings like:
brcmfmac 0001:04:00.0: Falling back to user helper
firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
