When configuring the radio in legacy mode from luci, the htmode is not set
correctly to NOHT, causing the radio in mesh mode to be set to HT40.
Signed-off-by: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
The user can now enable the ACK timeout estimation algorithm (dynack)
for drivers that support it.
It is also expected that the distance config accepts the same values as:
$ iw phyX set distance XXX
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
* uci state was not getting reset properly during teardown
* AP+STA co-exist state was not flushed properly upon channel switch
* remove a debug logger call
* properly teardown supplicant instances when they get disabled
* add md5 config support for supplicant
* don't call wpa_supplicant_prepare_interface twice
Signed-off-by: John Crispin <john@phrozen.org>
Some FullMAC cfg80211 wireless devices do not support virtual
interfaces, hence there is script logic to keep the existing network
device. Improve this to support renaming the interface if needed and
make sure the existing interface actually belongs to the right phy.
Change calls to 'iw' to avoid outputing warnings and errors to not
confuse users of such devices.
Also bump PKG_RELEASE which has been forgotten in the previous two
mac80211 changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of using the actual interface name, a hard-coded 'wlan0' has
slipped into the script. Replace it.
Fixes: ccf2aa9d4b ("mac80211: detect existing interface before adding")
Reported-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
hostapd allows putting WDS (4addr mode) clients into a separate bridge
other than the bridge regular (3addr mode) clients end up in. This is
useful for example giving WDS clients access to several VLANs
(trunking) while regular clients will end up inside a specific VLAN.
Add 'wds_bridge' config parameter for wifi-iface which contains the
name of the bridge. hostapd-mini already supports this feature, so all
needed is to add the UCI wrapping in mac80211.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Network interfaces are looked up based on the device behind a phy, so the
phy needs to be checked separately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With this patch, txpower for the PHY is applied when configuring the PHY
instead of the VIF. Otherwise, the configured txpower is not applied for
the first initialized VIF when using DFS channels, as it is currently
applied too early when the CAC hasn't finished.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
If no AP is configured, hostapd-${phy}.conf is not being created,
hence md5sum fails and causes log pollution:
netifd: radio1 (3183): md5sum: can't open '/var/run/hostapd-phy1.conf': No such file or directoy
Hence make sure the file exists when calling md5sum.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before commit 60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In addition to wpa_supplicant and hostapd managed interfaces, also
track unmanaged interfaces. This is used to make sure that running
'wifi' always returns into a clean state regardless of what the user
did before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This also fixes mac80211_prepare_vif iw set channel in monitor or
mesh mode.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed commit message]
Commit b3d8b3a introduced a new test:
[ -n "$noscan" -a "$noscan" -gt 0 ] && hostapd_noscan=1
But if length of "$noscan" is zero (noscan is not set) this doesn't stop
the shell to evaluate the rest of the test.
root@hank2:~# [ -n "$noscan" -a "$noscan" -gt 0 ]
ash: out of range
root@hank2:~#
So when radios are brought up this shows in the log:
Sat Nov 23 10:51:38 2019 daemon.info procd: - init complete -
Sat Nov 23 10:52:24 2019 daemon.notice netifd: radio1 (1243): sh: out of range
Sat Nov 23 10:52:25 2019 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sat Nov 23 10:52:25 2019 daemon.notice netifd: radio0 (1242): sh: out of range
Sat Nov 23 10:52:26 2019 authpriv.info dropbear[1536]: Not backgrounding
This commit sets noscan to 0 if unset and removes the gratuitous length
check, preventing the warning.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Keep existing wdev when creating new nl80211 interfaces if phy and
type match, delete it otherwise.
To make this work, also remove left-over debugging function which
prevented the return-value of the 'iw' command to be taken into
account in mac80211_iw_interface_add().
As 4addr-mode (WDS) was setup during interface creation for station
interfaces, also set it after interface creation to make sure an
existing sta interface ends up with the right mode.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes introduced for dynamic wifi reconfiguration left behind
unmanaged interface types. Restore parts of the old function to
also clean (unencrypted, non-DFS) mesh and ad-hoc interfaces.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Change scripts to use ubus interface of hostapd/wpa_supplicant to
add/remove/modify wireless interfaces instead of (re-)starting the
services.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The device path will be the same for the first phy. For all subsequent
phys, the path gets an extra +1, +2, ...
Move the code for converting path to phy and vice versa to a separate
library script shared by config detection code and the netifd wireless
handler script
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The channel can be selected automatically at run time by setting
channel=acs_survey or channel=0, both of which will enable the ACS survey
based algorithm in hostapd. If the option acs_exclude_dfs is set in the
hostpad config DFS channels from ACS are excluded on channel selection.
This commit will add the possibilty to exclude the dfs channel on ACS
survey.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
By default, set BE tx queue TXOP limit to 1.0 in the hostapd config
Many vendor drivers are doing similar things to boost throughput.
On MT7612 under ideal conditions, it improves tx throughput from 470 Mbit/s
to about 570 Mbit/s.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The keyword "all" is only supported by `iw set antenna` if
it's used as the only argument.
Convert "all" into a mask before calling `iw set antenna`.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Currently it's close to impossible to tell what part of mac80211 setup
went wrong. Errors logged into system log look like this:
radio0 (6155): command failed: No error information (-524)
radio0 (6155): command failed: Not supported (-95)
radio0 (6155): command failed: I/O error (-5)
radio0 (6155): command failed: Too many open files in system (-23)
With this commit change it's getting clear:
command failed: No error information (-524)
Failed command: iw dev wlan0 del
command failed: Not supported (-95)
Failed command: iw phy phy0 set antenna_gain 0
command failed: I/O error (-5)
Failed command: iw phy phy0 set distance 0
command failed: Too many open files in system (-23)
Failed command: iw phy phy0 interface add wlan0 type __ap
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refactor mesh initialization into a separate function, do some cleaning
on the way to make the code more readable.
Changes:
* Move iw mesh setup to new mac80211_setup_mesh()
* fallback on 'ssid' parameter in case 'mesh_id' isn't set
* move setting of freq variable to shared code as it is needed for
both, the wpa_supplicant and the iw based setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The commit 574e4377fa ("mac80211: properly setup mesh interface") uses
the variable $wpa to decide whether encrypted meshpoint is requested by the
user or not. But the variable $wpa will only be set correctly after the
function wireless_vif_parse_encryption is called.
Fixes: 574e4377fa ("mac80211: properly setup mesh interface")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Setup wpa_supplicant for encrypted mesh or when using DFS channels and
adjust interface setup to pass fixed frequency for mesh mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before this commit, devices supporting both 2.4GHz and 5GHz would be
configured for 2.4GHz by default - unless they have VHT capabilities.
With this commit, channel 36 is only set when the frequency is supported.
VHT isn't checked unless that is the case.
Signed-off-by: Leon M. George <leon@georgemail.eu>
This reverts commit 1356a66f94.
The change breaks wpa_supplicant.conf generation, more work is needed
to fix mesh+AP.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Unlike when operating in Ad-Hoc mode, we apparently need to pass the
hostapd control socket interface to wpa_supplicant when using 802.11s
mesh mode.
There also seems to still be something wrong with the logic setting
channel and (v)htmode parameters...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Remove obsolete patch chunks regarding fixed_freq
- Instead of patching in custom HT40+/- parameters, use the standard
config syntax as much as possible.
- Use fixed_freq for mesh
- Fix issues with disabling obss scan when using fixed_freq on mesh
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Passing the ctrl iface to wpa_supplicant will automatically cause wpa_supplicant
to send "STOP_AP" messages to the hostapd. This breaks the AP interfaces.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
Gracefully handle cases where the to-be-created wireless interface already
exists on the system which might commonly happen with non-multi-SSID capable
wireless drivers.
This fixes commit 8301e61365 which caused
previously ignored "Too many open files in system (-23)" errors to fail the
wireless setup procedure.
With the updated approach we'll still try recreating the vif after one
second if the first attempt to do so failed with ENFILE but we will now
consider the operation successfull if a second attempt still yields ENFILE
with the requested ifname already existing on the system.
Fixes FS#664, FS#704.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.
Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.
But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.
When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.
Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)
This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Some debugging/error messages are printed using wpa_printf and this
change allows finally reading them out of the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Previously, wifi detect simply dumped its generated wireless
configuration to STDOUT. A second step was needed to append
the configuration to /etc/config/wireless (or create it, if
it didn't exist).
With this patch, The wifi detection script will now use uci
to update the wireless configuration directly.
This patch also makes the initially created wifi-iface a
named section ('default_radio$X' for mac80211 and
'default_wl$X' for broadcom). With this change, uci will
not print the cfgHASH to STDOUT (which would now corrupt
the wireless configuration). It will also prevent adding
duplicated wifi interface configurations, if the wifi
configuration is run concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- Fix calculation of `$vht_cap` bit field
- Replace wrong reference to `$tx_stbc` variable with proper `$tx_stbc_2by1` one
- Emit proper `RX-STBC-{1,12,123,1234}` tokens for the VHT capability list
See https://dev.openwrt.org/ticket/22535 for reference.
Signed-off-by: Scott Shambarger <devel@shambarger.net>
LEDE project seems to be using "LEDE" as its acronym everywhere. To keep
things consistent adjust default wireless SSID.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Alexander Couzens <lynxis@fe80.eu>
The "iw" utility expects the VHT80 to be specified as uppercase "80MHZ",
change the script to reflect that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47814
Add a new config option "channels" for mac80211 wifi devices. It's only
valid if automatic channel selection is used and restricts the channel
selection to one of the given channels.
config wifi-device
list channels 1
list channels 6
list channels 11
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47427
In order to set the multicast rate for mesh point interfaces the "mesh join"
was made explicit and moved to mac80211_setup_vif(), similar to how it is
done for IBSS interfaces.
Previously, the mesh join was made implicit in case authentication (i.e.
$key) was not used when creating the interface in mac80211_prepare_vif(),
while using authentication would create the interface first, then join
later in mac80211_setup_vif() by starting authsae.
Signed-off-by: Nils Schneider <nils@nilsschneider.net>
SVN-Revision: 47408
Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Part of rev 44173 added setting the SM Power Save capability in the hostapd.conf
file if the driver indicated that it was supported. It appears this was
incorrect, because the field in the actual HT Capabilities field in the AP
configuration is really a state indication. Just copying the state from the
capability resulted in the AP indicating that it had SMPS enabled all the time
if it supported SMPS. This effectively just disables all clients from sending
packets to the AP with more than one spatial stream, for no good reason.
So remove this part of the change.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44239
Add some missing 802.11n capabilities to the hostapd ht_capab string when
supported by the hardware: Spatial Multiplexing Power-Save and 7935-byte AMSDUs.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44173
If '/sys/class/ieee80211/phyN' is not a symlink, the call to readlink
produces either an empty path (if /sys/class/ieee80211/phyN/device doesn't
exist) or a path that begins with '/sys/class/ieee80211' (which does not
work with the subsequent line to strip '/sys/devices' from the beginning of
the path). Modify the checks to detect these conditions, and fallback to
using the macaddr.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44172
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
This change introduces support for wildcard patterns in "option path"
of section "wifi-device".
Objective is to allow paths like "*/usb[0-9]/*/*" in order to claim
any usb device using the same backend type, regardless of its bus
address or phy name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41873
The vif option dtim_period was accidently renamed dtim_interval in r38988
("netifd: add wireless configuration support and port mac80211 to the new
framework"). This is wrong and makes the dtim_period/dtim_interval a dead
option because the rest of the config generation code still uses dtim_period.
Reported-by: Jeppe Ledet-Pedersen <jlp@steinwurf.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41557
r40682 ("mac80211: clean up ht capability handling, drop the use of the
ht_capab list, use individual variables instead") removed the ht_capab list and
replaced it with optional variables to disable features for a phy. But these
variables weren't added in drv_mac80211_init_device_config and thus didn't make
any difference when modifying /etc/config/wireless.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41180
This patch enables netifd to query 802.11ac-driver for the maximum
supported A-MPDU length exponent, possibly increasing VHT throughput by
more aggressive frame aggregation.
v2: refreshed patch
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40938
... or else "option htmode" is added multiple times to
the second and following device sections.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 40711
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 40497
