For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Lets update to 2024.04 in order to drop all of the patches as they have
been merged upstream.
Tested on Methode eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
f9a28a9ce864 ustream-ssl: poll connection on incomplete reads
3c49e70c4622 ustream-ssl: increase number of read buffers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reduce calls and pipes and read from urandom once directly with hexdump
for the necessary 5 bytes of random data to build the 48 bit ULA Prefix.
Fewer calls and forks; finish quicker; less memory used.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch fixing rmmod and insmod. Lots of flawed logic fixed that
permits the module to correctly rmmod and insmod later.
Just to quote some change, use phy_detach instead of phy_disconnect, fix
exclusive reset_control that could only be used once, fix kernel panic
on second edma_cleanup, stop traffic before module exit...
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a9e22ffa50.
After doing a clean rebuild, it turns out that this change is not necessary
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3159bbe0a2eb improve isolation when selecting a fixed output port
c77a7a1ff74d nl: fix getting flow offload stats
a08e51e679dd add support for disabling bridge-local flows via config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The new script uses a different strategy compared to the previous one.
Instead of trying to split flows by hash and spread them to all CPUs,
use RPS to redirect packets to a single core only.
Try to spread NAPI thread and RPS target CPUs across available CPUs
and try to ensure that the NAPI thread is on a different CPU than the
RPS target. This significantly reduces cycles wasted on the scheduler.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As commit 3ce1e4c3d3 ("d1: define subtarget specifically") added the
'generic' subtarget, without 'BUILD_SUBTARGET' the correspond U-Boot
package will be no longer selected automatically.
Fixes: 3ce1e4c3d3 ("d1: define subtarget specifically")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Update to the latest upstream release to include recent improvements and
bugfixes. Update copyright, fix typo in PKG_NAME, and remove unneeded use
of MAKE_VARS definition in Makefile. Drop 001-cflags.patch and simplify
002-includes.patch after refreshing. Also simplify LTO/DCE build flags.
Link: https://github.com/libbpf/bpftool/releases/tag/v7.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update to the latest upstream release to include recent improvements and
bugfixes, and update copyright. Remove MAKE_VARS usage in Makefile and drop
001-cflags.patch which are no longer needed. Also add flags to disable LTO,
mistakenly dropped earlier.
Link: https://github.com/libbpf/libbpf/releases/tag/v1.4.0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").
As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
e209a4ced1d8 add strdupa macro for compatibility
af1962b9a609 uclient: add helper function for getting ustream-ssl context/ops
488f1d52cfd2 http: add helper function for checking redirect status
b6e5548a3ecc uclient: defer read notifications to uloop timer
352fb3eeb408 http: call ustream_poll if not enough read data is available
e611e6d0ff0b add ucode binding
ddb18d265757 uclient: add function for getting the amount of pending read/write data
980220ad1762 ucode: fix a few ucode binding issues
6c16331e4bf5 ucode: add support for using a prototype for cb, pass it to callbacks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is mostly a cosmetic cleanup. The absence of
the return statement was not causing any problems.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
So, when updating the hash for at91bootstrap it was done via CHECK_ALL=1
so that updated the PKG_MIRROR_HASH for the main v4 version hash, but
at91bootstrap checkout version depends on the subtarget as well.
Choosing to build for sam9x will change the at91bootstrap version to v3
and this hash was not refreshed thus causing the CI to fail.
Fixes: 6918c637b7 ("treewide: package: update missed hashes after switch to ZSTD")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes.
This was missed in the initial treewide updated.
Fixes: b3c1c57a35 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When an IBBS interface is configured for IBSS legacy mode, wdev.htmode
is empty. This is empty string results in an empty positional argument
to the "ibbs join" command, for example:
iw dev phy0-ibss0 ibss join crymesh 2412 '' fixed-freq beacon-interval 100
This empty argument is interpreted as an invalid HT mode by 'iw',
causing the entire command to fail and print a "usage" message:
daemon.notice netifd: radio0 (4527): Usage: iw [options] \
dev <devname> ibss join <SSID> <freq in MHz> ...
Although nobody will ever need more than 640K of IBSS, explicitly use
"NOHT" if an HT mode is not given. This fixes the problem.
Fixes: e56c5f7b27 ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [extend to cover more cases]
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
