Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ClearFog GT 8K is device sold by SolidRun. It is marketed as a
development board, not a consumer product. The device tree file for this board
is upstream in kernel.org.
Signed-off-by: Logan Blyth <mrbojangles3@gmail.com>
This enables armv8 crypto extensions version of AES, GHASH, SHA1,
SHA256, and SHA512 algorithms in the kernel.
The choice of algorithms match the 32-bit versions that are enabled in
the target config-5.10 file, but were only used by the cortexa9
subtarget.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Enable the AP806's cpufreq driver. This driver is compatible with the
Armada 7K and 8K platforms.
Tested-by: Stijn Segers <foss@volatilesystems.org> (RB5009UG+S+IN)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
The option is already enabled in the target config since 9149ed4f05
("mvebu: cortexa9: Add support for Ctera C200-V2").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
While an image layout based on MBR and 'bootfs' partition may be easy
to understand for users who are very used to the IBM PC and always have
the option to access the SD card outside of the device (and hence don't
really depend on other recovery methods or dual-boot), in my opinion
it's a dead end for many desirable features on embedded systems,
especially when managed remotely (and hence without an easy option to
access the SD card using another device in case things go wrong, for
example).
Let me explain:
* using a MSDOS/VFAT filesystem to store kernel(s) is problematic, as a
single corruption of the bootfs can render the system into a state
that it no longer boots at all. This makes dual-boot useless, or at
least very tedious to setup with then 2 independent boot partitions
to avoid the single point of failure on a "hot" block (the FAT index
of the boot partition, written every time a file is changed in
bootfs). And well: most targets even store the bootloader environment
in a file in that very same FAT filesystem, hence it cannot be used
to script a reliable dual-boot method (as loading the environment
itself will already fail if the filesystem is corrupted).
* loading the kernel uImage from bootfs and using rootfs inside an
additional partition means the bootloader can only validate the
kernel -- if rootfs is broken or corrupted, this can lead to a reboot
loop, which is often a quite costly thing to happen in terms of
hardware lifetime.
* imitating MBR-boot behavior with a FAT-formatted bootfs partition
(like IBM PC in the 80s and 90s) is just one of many choices on
embedded targets. There are much better options with modern U-Boot
(which is what we use and build from source for all targets booting
off SD cards), see examples in mediatek/mt7622 and mediatek/mt7623.
Hence rename the 'sdcard' feature to 'legacy-sdcard', and prefix
functions with 'legacy_sdcard_' instead of 'sdcard_'.
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we have a generic sdcard upgrade method, which was copied from
the mvebu platform method, we can switch mvebu to the generic method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add symbol to generic config (this was added between 5.4 and 5.10),
and remove it from the targets where it was added by kernel_oldconfig
in the meantime.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also delete already upstreamed patches/changes.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Just a simple copy, no refresh yet.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[do not duplicate files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove the implicit/inherited symbols. While not strictly necessary, this will
make reviewing the diff between 5.4 and 5.10 easier.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Installation:
Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.
In the U-Boot Environment:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually (hanging lines indicate wrapped one-line command):
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
$image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr - $fdt_addr'
saveenv
On newer Bootloaders (18.12) the Variables have been changed, use:
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
$image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr_r - $fdt_addr_r'
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For the mvebu target in particular, there is a lot of files in
base-files that are only relevant for one subtarget. Improve
overview and reduce size per subtarget by moving/splitting
base-files depending on the subtarget they belong to.
While at it, consolidate 01_leds by using the model part of
the board name as variable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This refreshes the kernel 4.19 configuration, it looks like this was not
done initially.
When did a compile with the default settings I had to select some
kernel configuration options.
Fixes: 98684d99b2 ("mvebu: add kernel 4.19 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
[added sfp related patches from Russell King]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
[rebase; rework patches; separate and cleanup kernel configs;
add espessobin dts; adjust venom dts]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This removes support for executing old 32 bit applications on 64 bit ARM
and MIPS kernels.
On OpenWrt we normally compile all the user space applications on our
own and do not support third party binary only modules especial not 32
bit applications on 64 bit CPUs.
This reduces the attack surface on such systems and should also save
some memory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates "Emulate Privileged Access Never using TTBR0_EL1
switching" on ARM64.
This should prevent the kernel from reading code from user space in
kernel context.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This refreshes the current kernel configuration to remove unneeded
options, add some automatically added ones and reorders them. The normal
build did this automatically, so the builds already used this
configuration.
CONFIG_HW_RANDOM_OMAP is explicitly activated for the cortexa72
subtarget because it has an inside-secure,safexcel-eip76 IP core.
This was done with this command on the cortexa9 subtarget:
make kernel_oldconfig
and this one on the other subtargets:
make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is enabled in all subtargets, move it to common kernel
config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Rosen Penev <rosenp@gmail.com>
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.
This mitigates CVE-2018-3639 on ARM64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell
ARMADA 8040 Community board. Comes in two forms: Single Shot and Double
Shot.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) via copper or SFP
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Booting from micro SD card:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually:
setenv fdt_name armada-8040-mcbin.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr'
saveenv
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
