Support for kernel 4.14 was added 2 months ago, make it now the default
kernel to use for the x86 target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stijn Segers <francesco.borromini@inventati.org>
The gzip step in the sdcard image build fails because the image filename
already has the gzip extension. This results in an empty image file, to
which the metadata is finally appended.
Remove the .gz extension from the image filename to fix this.
Fixes: e79b096ee1 ("brcm2708: convert to metadata")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In the initial patch which adds HSDK board there were no update
of network configuration scripts. Without it by default static IP
is set for br-lan and there is no access to internet.
This patch fixes the issue.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
The Orange Pi Zero Plus uses a RTL8211E, add the driver for this PHY.
This is probably used on more boards with a Allwinner SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").
Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
On MT7621, the REG_ESW_VLAN_VTIM reads are undefined, causing swconfig
to always report `vid: 0` in swconfig show output.
Since a 4K VLAN table is used on this platform, the VLAN ID always
correponds to the actual VLAN table index so provide a specific MT7621
implementation of the get_vid callback which returns the table index
as VLAN ID.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Currently, untagged port primary vlan IDs are set to the VLAN table index,
and not the actual VLAN ID, breaking configurations with IDs deviating from
the VLAN index.
Fix the issue by resolving the per-port pvid property to the target VLAN ID
value before committing to the hardware.
Fixes FS#991, FS#1147, FS#1341
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Avoid overwriting vlan entries with remapped vid in later iterations of
the vlan enumeration loop of mt7530_apply_config().
Fix the problem by refactoring the code to first reset the entire table,
then reprogram only vlans with members to prevent overwriting configured
vlans with unconfigured ones.
Fixes FS#1147, FS#1341
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:
- Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
which is not available when building with CONFIG_TARGET_MULTI_PROFILE
- Build/at91-sdcard, which may run concurrently, creates scratch files at
fixed locations and manipulates target files directly which can lead
to file corruption and other unexpected failures
Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.
Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.
Finally remove the broken install-zImage from the generic image-commands
Makefile.
Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This drops support for all the !emmc EVB and adds banannaPi-R2
Also drop mtkhnat until the nftables offoad driver is ready
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Synopsys DesignWare HSDK (which stands for ARC HS
Development Kit) is the latest and greatest development
platform that sports quad-core ARC HS38 in real silicon.
Most noticeable features of the board are:
* Quad-core ARC HS38 CPU running at 1GHz
* 4Gb of DDR
* Built-in Vivante GPU (well supported via open source
Etnaviv drivers)
* Built-in Wi-Fi/Bluetooth module (RedPine RS-9113)
And as usual we have:
* [micro] SD-card slot
* 2 USB 2.0 ports
* 1Gbit Ethernet port
* Built-in Digilent JTAG probe
* Serial port accessible via micro-USB port
For more information about HSDK board visit:
https://www.synopsys.com/dw/ipdir.php?ds=arc-hs-development-kit
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
We have managed to get USB 2.0 working good enough
on all archs38 platforms so we're ready to switch
to much faster USB 2.0.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
sysfs attributes 'port_mask' & 'speed_mask' held locks whilst doing
mundane tasks such as sprintf. Refactor code to reduce length of time
locks are held unnecessarily.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add sysfs 'mode' attribute to swconfig controlled LEDs.
swconfig 'link state' LEDs blink in the presence of port traffic. This
behaviour becomes more obvious as switches start to support
get_port_stats() e.g. commits 0369e35891,
3056d09b40,
4ddbc43cc1,
4d8a66d934.
This blinking can be confusing/distracting if the switch has other LEDs
used to indicate traffic. Provide a 'mode' sysfs attribute that
controls the blink on traffic behaviour.
mode - either "none" (LED is off) or a space separated list of one or more:
link: LED's normal state reflects whether the link is up (has carrier) or not
tx: LED blinks on transmitted data
rx: LED blinks on receive data
Note that 'link' considers any port speed mask that may be applicable.
e.g. if an LED is configured to indicate 1Gbit link speed and mode is
set to 'link rx tx' but the port is connected at 100Mbit then the LED
will not light or blink. A mode of 'tx rx' will blink in the presence of
traffic only if the port matches the rate (if configured)
This maintains compatibility with existing behaviour.
Attribute is 'link tx rx' by default for backwards compatible behaviour.
Many thanks to Thibaut Varene for providing a more sensible led_event
routine after I had mangled the original, and other coding style hints.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
The name of the PCIe controller node in device tree changed between
kernel 4.9 and kernel 4.14. Migrate the configuration when an update
from kernel 4.9 to 4.14 or back is done to the new name to make
the existing wifi configuration compatible with the new names.
This replaces the "pcie-controller" part with "pcie" on all nodes if the
file exists in sys fs.
This is not done in the uci-defualts, because they are getting executed
to late in the boot process. The kernel module gets loaded before the
uci-defaults scripts are executed. When the mwlwifi driver gets loaded
it will trigger an event via hotplug to detect new devices and as the
paths are not in the uci configuration they will be added again.
When the migration is done before the script will detect that they are
already there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for kernel 4.14 to the mvebu target.
This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is needed to prevent copying it into kernel 4.14.
These device tree files are already integrated into kernel 4.14 and we
would like to use the upstream versions only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of creating an ubifs file system with format version 5 by
default on empty UBI volumes use the older format 4 by default. This
will make it possible to mount these file systems also on older kernel
versions.
When a user wants to do a sysupgrade from kernel 4.14 to kernel 4.9 the
old kernel has to read the file system created by the more recent kernel
which currently does not work for ubifs.
This fixes the problem by creating file systems which are compatible
with older kernel versions by default.
Kernel 4.14 will still be able to read and write UBI FS file system
version 5, it will just not be used when a ubifs partition is created
implicitly on an empty UBI volume.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The root= parameter overrides the automatic rootfs detection by partition
name, so drop it. Fixes boot from flash after renumeration changes of
partitions due to parser changes.
Fixes FS#1350.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.
The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
PHY drivers were grouped into vendor specific directories
by upstream commit 0b56e9a7e8358e59b21d8a425e463072bfae523c
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.
Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.
Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)
Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image
Signed-off-by: George Hopkins <george-hopkins@null.net>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
The tftp.bin image for Buffalo WHR-G300N was not built, so I was fixed
it after rewriting to new image build code. And the code for
factory-EU.bin was broken, so I deleted it.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
- Remove kernel 4.9 support
- Apply specific 4.14 changes directly to source
- Refreshed all
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Cavium OCTEON TX is an ARM 64-bit SoC leveraging CPU cores and
periperhals from the Cavium ThunderX SoC.
This initial support provides a 4.14 kernel and kernel+initramfs that is
bootable on the Gateworks Newport GW630x as well as the Cavium sff8104
reference board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Device Tree file for I2SE Duckbill boards was updated upstream.
Let's use the upstream version for upcoming kernel 4.14 by keeping
our current version for v4.9 still around.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Errata:
- While there are three ethernet ports, the third requires support for
the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
headers. Workaround is to pull the headers out and connect the pins to
jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
/dev/sdX reads throw silent errors. The current theory behind this is
some kind of unhandled DMA mapping error in the kernel. This is not an
issue with kernel 4.4.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Updated pfe kernel patch to clean up iounmap(pfe->ddr_baseaddr).
pfe->ddr_baseaddr was got through phys_to_virt() not ioremap(),
so iounmap() for pfe->ddr_baseaddr should be removed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add a known issue of make menuconfig
in README file. This is also a common issue for OpenWrt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch changes the declarations of ndo_get_stats64 handlers
to the previous struct rtnl_link_stats64 * return type instead of
the mainline void return.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tis patch is to fix up some descriptions in README.
Per-device rootfs had been supported, and a known issue
had been found. These also should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some layerscape devices (ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb)
were using ext4 rootfs because there were issues using squashfs.
This patch is to drop using ext4 rootfs and use ubifs rootfs instead
which is more proper for SPI-NOR flash.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to remove USB configs for 32-bit device since
they're already in kmod package. Also removed TI platform
specific configs.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Patches changes
- Updated patches-4.9 to NXP LSDK1712 linux-4.9.
- Merged changes of patch 303 into integrated patch 201.
- Split changes of patch 706 into dpaa part and dpaa2
part, and merged these changes into integrated patches
701 and 705.
- Removed patch 819 since ehci-fsl driver could be compiled now.
- Refreshed these patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This will introduce a warning on 3.18, but fixes an error when
compiling for 4.9.
Fixes: cf9e0a59aa ("ar7: add kernel 4.9 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When clearfog was renamed to clearfog pro, it broke sysupgrade from
17.04 as the new images now get rejected as incompatible. Fix this by
adding the legacy boardname to the compatible devices.
Fixes: ec4a8c6dee ("mvebu: ClearFog renamed upstream to ClearFog Pro")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for kernel 4.9 based on the more upstream comformant
partition defintions. Increases compressed kernel size by ~95k
compared to 4.4.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Partitions are supposed to be enclosed in an extra partitions node. Allow
the bcm63xxpart parser to cope with that.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The lookup needs to be called just "reset" for the common code.
Fixes: 054c0d4e31 ("brcm63xx: backport mdio-bus reset gpio support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The arm CPUs uses in the supported Mediatket SoCs have a FPU accordingly
to the datasheet, activate it also. The CPU subtype "neon-vfpv4" is
selected, but the toolcahin generated for this SoC will still be
compiled with soft float and not with the hard float ABI as we haven't
the fpu feature flag set. If this toolchain is reused by other targets
this will even affect other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Flash instruction:
The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).
This driver find jImage header and set rootfs start after kernel file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use "$(DTS_DIR)", defined at include/image.mk, instead of
"$(LINUX_DIR)/arch/$(LINUX_KARCH)/boot/dts" in order to generalize and
allow a better Device/* device-tree parameterization (i.e. DEVICE_DTS_DIR
and DTS_DIR).
Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
Update Linux kernel version from 4.9 to 4.14 for archs38.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
This config option was renamed in upstream Linux commit 681bec0367
("tracing: Rename update the enum_map file")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Convert userspace code to use generic device-tree compatible board
detection method. Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.
Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Locally generated packets weren't forwarded to the isolated interfaces in a
bridge. Isolation should only prevent the flooding of incomming packets to
other interfaces in the bridge.
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Qualcomm claims this improves the D-cache footprint. Origina commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf
Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them. Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.
Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add the Embedded Wireless "Balin" platform
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCI-Express: 1 x lane PCIe 1.2
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Widora has updated their Widora Neo board recently.
The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.
All the other hardware components are the same as
the first revision.
Detailed hardware specs listed below:
CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
USB Power+Serial (CP2104);
3x LEDs (Power, LAN, WiFi);
2x Keys (WPS, CPU Reset)
1x Audio In/Out
1x IPEX antenna port
1x Micro SD slot
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.
Migrate the Widora neo to the generic board detection as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When CGROUPS is enabled the new option CONFIG_CGROUP_NET_CLASSID is
selectable and not handled.
Add this option to the 4.9 kernel configuration.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The USB Ethernet is not working with the patches proposed for upstream,
fix this and activate the SPI node as this board always has a SPI flash.
Both patches are also targeted for upstream kernel 4.16 and 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of using our own device tree definitions use the one provided in
the upstream kernel for 4.16.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ethernet support was initial added in kernel 4.13, but deactivated
before the final release. This is backports the changes which are
activating it again from kernel 4.15.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is based on the code for kernel 4.9, but a lot of 4.9 patches are
backports from more recent kernel version and can be removed now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the sunxi kernel configuration.
This also moves the CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG option to the
config-4.9 file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:
https://mikrotik.com/product/RB911-2Hnhttps://mikrotik.com/product/RB911-5Hn
The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.
Specifications:
* SoC: Atheros AR9344 (600MHz)
* RAM: 64MiB
* Storage: 16 MiB SPI NOR flash
* Ethernet: 1x100M (Passive PoE in)
* Wireless: AR9344 built-in wireless MAC, single chain
802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)
Notes:
* Older versions of these boards might be equipped with a NAND
flash chip instead of the SPI NOR device. Those boards are not
supported (yet).
* The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
same hardware. Support for that can be added later with little
effort probably.
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its ethernet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
5. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
7. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add patches for the leds-gpio driver to make it usable with
open-drain and open-source kind of GPIO lines.
This type of functionality is required by various MikroTik boards.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.
Also update the board setup codes, to ensure that those handle the new
return value correctly.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.
Additionally, introduce two helper functions what make the processing
of the hardware options easy.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Support for Winbond NAND flash detection was added into the generic
patches and this conflicted with this patch adding Gigadevice support.
Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some part of this patch was added to the generic patches as it was
needed also for some other target. Do not add it here any more.
Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the new configuration option CONFIG_RETPOLINE and
refreshes the configuration.
Fixes: d8565a06dc ("kernel: bump 4.9 to 4.9.77")
Fixes: 9ddfac8015 ("kernel: bump 4.14 to 4.14.14")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This replaces the current patches used to make the kernel headers
compatible with musl with the version which was accepted upstream. This
is included in upstream kernel 4.15.
This was compile tested with iproute2 build on all supported kernel
versions with musl and one one with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
nftables 0.8.1 generates some new commands which will not work without
this on big endian systems. This patch is included in Linux 4.11 and
later.
My rule matching a TCP port was not working:
nft add rule ip foo bar ct state new tcp dport 22 accept
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
file is only partially upstream and therefore subjected
to changes that might not be compatible with the board.
As a result, the definitions from the file have been
copied into this dts.
- exclusively use decimal GPIO addresses.
- reorganize the reserved-memory layout to waste less
memory. There's no point in keeping the u-boot loader
around. This should also make it possible to create
an image that will boot with the original EVA/ADAM2 loader
without needing to install the modified u-boot loader.
And finally mark the "tz-apps" as reusable.
There isn't a way to upload apps to the trust-zone in OpenWrt
yet. But it might see some use in the future as a "secure"
key-store/TPM.
- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:
Image check 'platform_check_image' failed.
Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.
Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.
Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.
Compile tested only.
Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.
Refresh the patches with quilt to fix them.
Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.
Refresh the patches with quilt to fix them.
Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.
Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.
Add support for these.
Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3
Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."
Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.
A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).
Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.
In previous commit we've added the support for this option, so enable it in DT for affected devices.
QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506
While at it move the phy transmit termination offset value into dtsi file as it's platform specific.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197
This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch
Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.
Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.
Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Flash instruction:
The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.
Signed-off-by: David Bauer <mail@david-bauer.net>
As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.
Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.
See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
· Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
· Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
PoE in
Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button
Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)
Unsupported:
- ZT2046Q SPI temperature and voltage sensor
Contributors: Giuseppe Tipaldi (@Ciusss89)
Ricky (@rickydee)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.
Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.
Specification:
- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers
Flash instruction (do it under U-Boot, using UART and TFTP server):
Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Several new DRM symbols that were introduced after 4.9 are missing in
the generic config for 4.14, so add them.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.
This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a bunch of missing configuration symbols found while building
armvirt for 4.14 after re-synchronization of the configuration between
4.9 and 4.14.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This backports upstream support for "compatible" DT property set for the
"partitions" subnode of flash node. It allows specifying how partitions
should be created/parsed. Right now only "fixed-partitions" is
supported.
It should eventually replace our downstream "linux,part-probe" solution.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Multicast routing support is not needed in most setups, and increases the
size of the kernel considerably (>10K after LZMA). Add a config switch to
allow disabling it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The underlying issue breaking Spansion flash has been fixed with "mtd: spi-nor:
wait until lock/unlock operations are ready" and "mtd: spi-nor: wait for SR_WIP
to clear on initial unlock", so we can support unlocking for Winbond flash
again.
This is necessary to have writable flash on certain UBNT devices with some
bootloader versions.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump.
Boot tested both 32 and 64 bit subtargets using initramfs images with the
qemu-system-arm and qemu-system-aarch64 emulators.
Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01
SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)
This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.
-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.
Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.
Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".
Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.
Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.
Start the serial session and then power up the device.
As soon as you see text on the serial start pressing random
letter keys to stop the boot process.
If you see something like the following line you can proceed:
CE>>
Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.
write
printenv ethaddr
The uboot will write something like this:
ethaddr=00:50:43:00:02:02
This is the device's MAC address, also present in the sticker
under the device.
Write this down as we will need to add it in the
new uboot configuration.
Use the following commands to load the new uboot:
tftp 0x20000 u-boot.kwb
If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:
nand erase 0 0x200000
nand write 0x20000 0 0x1c0000
if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.
If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.
Now write:
reset
and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see
pogoplugv4>
We now add the MAC address back, write:
setenv ethaddr '00:50:43:00:02:02'
Confirm that the uboot has understood by writing
printenv ethaddr
If all looks ok, save the setting with
saveenv
At this point the uboot is configured, and we only need to load
the firmware in the flash memory.
Follow the steps below in "Firmware recovery procedure".
----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.
Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".
Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).
Power up the device, and wait for it to finish booting.
The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.
If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).
The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.
Add common used options/images to the default build code and override
the options where necessary.
Don't export the kernel image, it isn't required by any board.
While at it, change the file extension for the sysupgrade images to bin.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
