We need a+x rights on the path to the root of the jails
so we can use users other than root (like nobody)
This partly fixes jailed dnsmasq
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 46466
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This changes makes it possible to store custom settings
in individual files inside the directory /etc/sysctl.d/.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 46239
Depending on configuration, disable the LED before writing the trigger
and enable it after writing it. Fixes LEDs where the value defaults to 1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45463
Use xattr to store the filesystem initialization state of the overlay.
As long as the filesystem is not marked as initialized yet (happens in
/etc/init.d/done), all overlay data (except for sysupgrade.tgz) will be
discarded before the system is allowed to boot
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44942
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/http://patchwork.openwrt.org/patch/3553/
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42985
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42848
During boot, a not found message is displayed for systems which do
not have uci 'network.globals.ula_prefix' defined in
/etc/config/network. The error message itself is not used and can
be ignored.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42755
somebody started to set a function returncode in the validation
stuff and everybody copies it, e.g.
myfunction()
{
fire_command
return $?
}
a function automatically returns with the last returncode,
so we can safely remove the command 'return $?'. reference:
http://tldp.org/LDP/abs/html/exit-status.html
"The last command executed in the function or script determines the exit status."
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42278
this allows targets to use the new uci-default helper which will generate
a file called /etc/board.json. a tool called /bin/config_generate can then
be used to generate the default uci settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42185
Make sure they don't break the sed command, and also make device_info
and openwrt_release more robust for parsing by scripts
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41885
Creates /etc/device_info which will be used to fill in information for
WPS and other protocols that need manufacturer/device information
This helps with creating OpenWrt firmware for OEM or rebranded devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41884
Seems like the reverse order relies on GNU specific getopt hackery which
musl does not replicate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 41045
Since svn rev [38557] we support power buttons, for example
the ACPI power button on x86 machines.
Add a simple shutdown script to /etc/rc.button, to gracefully shutdown
the machine after the power button is pressed.
Tested on x86 and x86_64 in a kvm virtual machine.
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 40909
Before this patch, doing `/e/c/network restart' will emit the folloing
error by `ubus network.wireless down "{}"' because netifd already quit
by that time.
Command failed: not found
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40906
It was introduced in commit 2f966e8, "base-files: add a post start hook
for procd managed services".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 40576
Simply scan for the most recent file in /etc and set
system time to this file modification time if it's in the future
It allow some time dependent program to work immediatly
without waiting for ntpd to sync
v1: v2: bad approach
v3: simply scan /etc, thanks to Bastian Bittorf for the idea
v4: use sort -n, thanks to Catalin Patulea
v5: use [] instead of [[]], thanks to Andreas Mohr
v6: use openwrt style, thanks to Bastian Bittorf
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
SVN-Revision: 39422
Only reload hostname and timezone config on /etc/init.d/boot restart.
Module loading and basic boot setup is only done during boot.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 38670
This allows packages to override busybox applets by placing the new
binaries in /usr/{sbin,bin}
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36890
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh
/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.
SVN-Revision: 34792
Write "delay" and "message" options to their respective files,
allowing Morse code message configuration through UCI.
The delay (dit length) defaults to 150ms (about 8 words per minute,
suitable for beginners).
Signed-off-by: Petr Viktorin <encukou@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34380
Without this, /etc/init.d/led will try to set the non-existing 'rssi' trigger.
This doesn't harm as the kernel will refuse this setting, but it outputs some
ugly log-lines:
Jun 24 10:15:19 OpenWrt user.info sysinit: setting up led RSSILOW
Jun 24 10:15:19 OpenWrt user.info sysinit: sh: write error: Invalid argument
...
In order to avoid this, skip LEDs with trigger = "rssi" in /etc/init.d/led
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33717
When standalone ldd is selected in config the binary is installed in /usr/bin/ldd.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 32891
A year of testing in the cerowrt project shows not using timestamps
to be a very bad idea in nearly any TCP at speeds above a few Mbit.
Lastly sack/dsack help on recovery from larger amounts of packet
loss.
SVN-Revision: 32513
On slower devices wifi drivers might take too long for detecting
devices, resulting in the wifi detect call not seeing them.
This was observed on a bcm6348 with bcm4318 wifi. Adding a one second
pause was enough for b43 to expose the device.
SVN-Revision: 31639
hi
Another version, in this one the enable_server option is in the timeserver ntp part of the "system" config file
You can patch trunk and bacfire (tested both)
You can put busybox ntpd in client mode (if you put server), in client & server (by putting enable_server to 1, ntpd listen to udp 123), and also in server mode only (if you didn't put any servers in the config and still put enable_server 1, ntpd will answer with the time of the router)
I've replaced "config_foreach getpeers timeserver" with "config_get peers ntp server" because we want ntp timeserver, not random ones (to pre-answer if someone want to say that it's intrusive ...)
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
Le 27/03/2012 20:41, Etienne Champetier a écrit :
> I've now tested my trunk patch and it works fine
> But I still can't find were $PROG is defined (is this a mistake, or some sort of built in variable???)
> (I've made some grep and nothing)
>
> Le 23/03/2012 02:19, Philip Prindeville a écrit :
>> Maybe:
>>
>> [ -n "$PROG" -a -x "$PROG" ] || return 1
>>
>> instead?
>>
>>
>> On 3/22/12 4:34 PM, Etienne Champetier wrote:
>>> Hi
>>>
>>> The 2 attached patchs (trunk & bacfire) add busybox ntpd enable_server option, as busybox ntpd server is compiled by default.
>>> We only need 1 client/server daemon (olipro patch was launching 2 daemons)
>>> I've fully tested the bacfire patch, and as i don't have a running openwrt trunk i'm not sure for the trunk patch (i'm sure about my modifications, but i'm not sure about "[ -x $PROG ] || return 1", as "$PROG" isn't defined ?!)
>>>
>>> Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
>>>
>>>
>>> Le 16/01/2012 01:57, Philip Prindeville a écrit :
>>>> On 1/14/12 11:37 AM, Olipro wrote:
>>>>> On Saturday 14 Jan 2012 02:45:59 Philip Prindeville wrote:
>>>>>> Don't we already have a 'disabled' option? Now we're adding an
>>>>>> 'enable_server' option?
>>>>>>
>>>>>> That seems confusing for no useful reason.
>>>>>>
>>>>> have you bothered to read what I originally wrote? your response would make
>>>>> me inclined to believe that you didn't.
>>>>>
>>>>> currently the ntpd initscript only runs it as a CLIENT - this patch enables
>>>>> you to have one instance running as a client and another as a SERVER that
>>>>> other hosts can synchronise with.
>>>>>
>>>>> Or perhaps I'm misunderstanding, what would you propose for allowing the
>>>>> built-in busybox ntpd to be utilised as a server? a separate init script
>>>>> entirely perhaps?
>>>> Or separate config sections... instead of 'config ntp' have 'config ntp-server' and 'config ntp-client'.
>>>>
>>>> -Philip
>>>>
>>>>
>>>> _______________________________________________
>>>> openwrt-devel mailing list
>>>> openwrt-devel@lists.openwrt.org
>>>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
SVN-Revision: 31374
The available placeholders are:
%D .. Replace with $(CONFIG_VERSION_DIST), default to "OpenWrt"
%d .. Like %D, but all characters made lowercase and spaces substituted with "_" (e.g. "openwrt")
%N .. Replace with $(CONFIG_VERSION_NICK), default to the build tree release (e.g. "Attitude Adjustment")
%n .. Like %N, but all characters made lowercase and spaces substituted with "_" (e.g. "attitude_adjustment")
%V .. Replace with $(CONFIG_VERSION_NUMBER), default to the build tree release (e.g. "r31262")
%v .. Like %V, but all characters made lowercase and spaces substituted with "_"
%C .. Replace with $(CONFIG_VERSION_NUMBER), default to "Bleeding Edge"
%c .. Like %C, but all characters made lowercase and spaces substituted with "_" (e.g. "bleeding_edge")
%U .. Replace with $(CONFIG_VERSION_REPO), default to "http://downloads.openwrt.org/snapshots/trunk/%T/packages"
%R .. Replace with the current build tree revision (e.g. "r31262" or "75488c4a05b8033cf69e91874a61852db7ba9c6c")
%T .. Replace with the current target (e.g. "ar71xx")
%S .. Replace with the current target/subtarget combo (e.g. "adm5120/router_le")
SVN-Revision: 31262
The muninlite postinst fails to add munin to /etc/services.
This patch removes this broken postinst and add an entry for munin in
/etc/services. This should have been done when the rest of the
/etc/services postinsts were being removed (changesets 26142-26149).
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
SVN-Revision: 30982
The script tests for the existance of /dev/root with test -e which fails if
/dev/root is a dangling symlink making the call to ln fail.
Signed-off-by: Justus Winter <4winter@informatik.uni-hamburg.de>
SVN-Revision: 26483
