Commit Graph

3380 Commits

Author SHA1 Message Date
Robert Senderek
ef5b1ffb9e ramips: rt3883: enable lzma-loader for Belkin F9K1109v1
Fixes boot loader LZMA decompression issues

Fixes: #10968
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
(cherry picked from commit ac296f6210)
2022-10-23 14:21:03 +02:00
Alex Khodin
b0ab21d9d0 ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1
Fixes boot loader LZMA decompression issues.

Without this change the board end up in a boot loop.

Signed-off-by: Alex Khodin <mxktz1@gmail.com>
(cherry picked from commit f6099d7974)
2022-10-23 14:21:03 +02:00
Petr Štetiar
8fefd5c26c mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit b63d6d4730)
2022-10-18 19:09:06 +02:00
Petr Štetiar
36a808b7bc mt7621: netgear_ex6150: fix reboot loop by using LZMA loader
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 7dd1cab1c1)
2022-10-18 09:05:08 +02:00
David Bauer
c1fcca50ba ramips: fix ZyXEL NWA55AXE model name
The model name was missing a letter.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 9c8605dee2)
2022-10-14 23:14:50 +02:00
David Bauer
2050bc4f64 ramips: add support for ZyXEL NWA50AX / NWA55AXE
Hardware
--------
CPU:    Mediatek MT7621
RAM:    256M DDR3
FLASH:  128M NAND
ETH:    1x Gigabit Ethernet
WiFi:   Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC)
BTN:    1x Reset (NWA50AX only)
LED:    1x Multi-Color (NWA50AX only)

UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.

Settings: 115200 8N1

Layout:

<12V> <LAN> GND-RX-TX-VCC

Logic-Level is 3V3. Don't connect VCC to your UART adapter!

Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.

As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.

If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.

If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.

Installation TFTP
-----------------
This installation routine is especially useful in case
 * unknown device password (NWA55AXE lacks reset button)
 * bricked device

Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.

The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.

Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin

 $ atnf owrt.bin
 $ atna 192.168.1.88
 $ atns "192.168.1.66; tftpboot; bootm"

Upon booting, set the booted image to the correct slot:

 $ zyxel-bootconfig /dev/mtd10 get-status
 $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid
 $ zyxel-bootconfig /dev/mtd10 set-active-image 0

Copy the OpenWrt ramboot-factory image to the device using scp.
Write the factory image to NAND and reboot the device.

 $ mtd write ramboot-factory.bin firmware
 $ reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a0b7fef0ff)
2022-10-14 23:14:50 +02:00
Felix Fietkau
b6487c3ccc ramips: skip bbt scan on mt7621
reduces unnecessary flash reads and speeds up boot time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 55e8d52157)
2022-10-10 18:14:30 +02:00
Felix Fietkau
33457ebf0b ramips: enable support for mtk_bmt in the nand flash driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 4947623d6c)
2022-10-10 18:14:26 +02:00
Felix Fietkau
cc8326443d ramips: mt7621_nand: initialize ECC_FDMADDR
This is needed for the ECC controller to access FDM data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 73b2a4ca03)
2022-10-10 18:14:22 +02:00
Stijn Tintel
1918404b1d ramips: mt7621_nand: reduce log verbosity
Avoid flooding the log with the message below by increasing the log
level to debug:

  mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry-picked from commit 89c1959251)
2022-10-10 18:14:18 +02:00
Stijn Tintel
07ea71c7b7 ramips: move mt7621_nand driver to files
The patch was rejected by upstream. The mtk_nand driver should be
modified to support the mt7621 flash controller instead. As there is no
newer version to backport, or no upstream version to fix bugs, let's
move the driver to the files dir under the ramips target. This makes it
easier to make changes to the driver while waiting for mt7621 support to
land in mtk_nand.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry-picked from commit 2f2e81a4ea)
2022-10-10 18:14:14 +02:00
Matthias Schiffer
25747a4c04 ramips: fix switch setup for ASUS RT-AX53U
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 149fc3a269)
2022-10-03 19:51:50 +02:00
Mark King
d30ddfbac4 ramips: enable LZMA loader to fix Linksys RE6500 boot
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.

Fixes: #8577

Signed-off-by: Mark King <mark@vemek.co>
(cherry picked from commit bf5b1a53d4)
2022-10-03 19:51:50 +02:00
Daniel Golle
7c459ac1d5 mac80211: rt2x00: experimental improvements for MT7620 wifi
Serge Vasilugin reports:

To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
	https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
   set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
    a) RF and BBP regs never be corrected for this mode
    b) eLNA is driven the same way as ePA with mt7620's pin PA
	but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
	so I'm not sure that request for pa_pin in dts-file will be enough

First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA

Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
 35-40/30-35 Mbps for HT20
 65-70/60-65 Mbps for HT40

Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.

Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[directly include v3 of the patchset submitted upstream]
(cherry picked from commit 31a6605de0)
(cherry picked from commit e785ca05e9)
(cherry picked from commit 412fcf3d44)
2022-09-19 02:48:26 +01:00
Sven Wegener
f54d4ea0bb ramips: add support for Ubiquiti UniFi FlexHD
Hardware
--------

- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Update the bootloader environment.

   $ fw_setenv devmode TRUE
   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

3. Transfer the OpenWrt sysupgrade image to the device using SCP.

4. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

5. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

7. Reboot the device. It should boot into OpenWrt.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 820f0c07c5)
2022-09-18 15:40:04 +01:00
Arınç ÜNAL
d10352917b ramips: fix GB-PC1 and GB-PC2 LEDs
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.

Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.

Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.

Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2a6ef7f53d)
2022-09-18 16:04:41 +02:00
Thibaut VARÈNE
dced5f2c95 ramips: define Yuncore AX820 switch LEDs
This patch defines the two switch LED to bring them under user control.

Fixes: 158a5af801 ("ramips: improve YunCore AX820 LEDs")
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[rmilecki: leave "label"s in place]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7bee10a7d2)
2022-08-29 16:23:26 +02:00
Arınç ÜNAL
d1f14d17aa ramips: fix GB-PC1 and GB-PC2 device support
Change switch port labels to ethblack & ethblue.
Change lan1 & lan2 LEDs to ethblack_act & ethblue_act and fix GPIO pins.
Add the external phy with ethyellow label on the GB-PC2 devicetree.
Do not claim rgmii2 as gpio, it's used for ethernet with rgmii2 function.
Enable ICPlus PHY driver for IP1001 which GB-PC2 has got.
Update interface name and change netdev function.
Enable lzma compression to make up for the increased size of the kernel.
Make spi flash bindings on par with mainline Linux to fix read errors.

Tested on GB-PC2 by Petr.

Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 4807bd6a00)
2022-08-26 22:30:56 +02:00
Mikhail Zhilkin
ecd8f7e294
ramips: get MAC addr from the encrypted partition (WG4хх223)
This commit resolves #10062. Adds decryption of the Arcadyan WG4xx223
configuration partition (board_data)to get base MAC address from it.
As a result, after this change the hack with saving MAC addressees to
u-boot-env before installation of OpenWrt is no longer necessary.

This is necessary for the following devices:
- Beeline Smartbox Flash (Arcadyan WG443223)
- MTS WG430223 (Arcadyan WG430223)

Example:
+----------------+-------------------+------------------------+
|                |    MTS WG430223   | Beeline Smartbox Flash |
+----------------+-------------------+------------------------+
| base mac (mtd) | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06      |
| label          | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:09      |
| LAN            | A4:xx:xx:51:xx:F6 | 30:xx:xx:51:xx:09      |
| WAN            | A4:xx:xx:51:xx:F4 | 30:xx:xx:51:xx:06      |
| WLAN_2g        | A4:xx:xx:51:xx:F5 | 30:xx:xx:51:xx:07      |
| WLAN_5g        | A6:xx:xx:21:xx:F5 | 32:xx:xx:41:xx:07      |
+----------------+-------------------+------------------------+

Collected statistic shows that the 2-4th bits of the 7th byte of the
WLAN_5g MAC are the constant (see #10062 for more details):
- Beeline Smartbox Flash - 100
- MTS WG430223 - 010

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit a6b0d08060)
2022-08-19 14:44:44 +02:00
Mikhail Zhilkin
464f349fad ramips: allow custom trx magic for Arcadyan
This commit:
1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe
   is necessary for:
   - MTS WG430223 (Arcadyan WG430223)
   - Beeline Smartbox Flash (Arcadyan WG443223)
2. Allows specify custom trx magic which is different for the routers
   mentined above.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 109c503bee)
[fix merging conflict in mt7621.mk]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-08-16 16:04:55 +02:00
Mikhail Zhilkin
7edaae16db ramips: create new dtsi for Arcadyan routers
This commit moves common properties for the boards below to a new dtsi:
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)

The boards are almost the same. Here is the differences:
+------+----------+----------+
|      | WG430223 | WG443223 |
+------+----------+----------+
| RAM  | 128      | 256      |
+------+----------+----------+
| USB  | -        | 1x3.0    |
+------+----------+----------+
| LEDS | RG       | RGB      |
+------+----------+----------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 5b59137a16)
2022-08-16 15:59:52 +02:00
Mikhail Zhilkin
206581018c ramips: add support for MTS WG430223
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223

Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
   enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
   uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
    awk '{print $5}')
   uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
    awk '{print $5}')
   uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
    awk '{print $5}')
   uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
    awk '{print $5}')
7. Ensure that MACs were saved correctly:
   uboot_env --get --name eth2macaddr
   uboot_env --get --name eth3macaddr
   uboot_env --get --name ra0macaddr
   uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
   cd /tmp
   wget http://192.168.1.2/factory.trx
   mtd_write erase /dev/mtd4
   mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
   uboot_env --set --name bootpartition --value 0

Back to Stock
-------------
1. Run in the OpenWrt shell:
   fw_setenv bootpartition 1
   reboot
2. Optional step. Upgrade the stock firmware with any version to
   overwrite the OpenWrt in Slot 1.

MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC               | Source         |
+-----------+-------------------+----------------+
| label     | A4:xx:xx:51:xx:F4 | No MACs was    |
| LAN       | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN       | A4:xx:xx:51:xx:F4 | [1]            |
| WLAN_2g   | A4:xx:xx:51:xx:F5 |                |
| WLAN_5g   | A6:xx:xx:21:xx:F5 |                |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
   key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
   with saving of the MACs to u-boot-env during the installation was
   applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
   "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
   firmware also uses this MAC when initialazes ethernet driver. In
   OpenWrt we use it only as internal GMAC (eth0), all other MACs are
   unique. Therefore, there is no any barriers to the operation of several
   MTS WG430223 devices even within the same broadcast domain.

Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset       |               | Description                            |
+==============+===============+========================================+
| 0x0          | 31 52 48 53   | TRX magic "1RHS"                       |
+--------------+---------------+----------------------------------------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 498c15376b)
2022-08-16 15:58:50 +02:00
Chuncheng Chen
1320a78aab ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
        3x LAN (blue, configurable)
        1x WAN (blue, configurable)
        1x USB (blue, not configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8c00fd9b45)
2022-08-16 15:42:11 +02:00
Nita Vesa
ca58b8b4fe ramips: Add Xiaomi Mi Router 4A 100M International
The international version of Mi Router 4A 100M is physically
identical to the non-international one, but appears to be
using a different partitioning scheme with the "overlay"
partition being 2MiB in size instead of 1MiB. This means
the following "firmware" partition starts at a different
address and the DTS needs to be adjusted for the firmware
to work.

Signed-off-by: Nita Vesa <werecatf@outlook.com>
(cherry picked from commit 1a8c74da70)
Signed-off-by: Tom Herbers <freifunk@tomherbers.de>
2022-08-09 21:22:41 +02:00
John Audia
7ca89e1187 kernel: bump 5.10 to 5.10.134
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 7be62b1187)
2022-07-30 17:22:16 +02:00
Wenli Looi
c240fed242
ramips: add support for Netgear WAX202
Netgear WAX202 is an 802.11ax (Wi-Fi 6) router.

Specifications:
* SoC: MT7621A
* RAM: 512 MiB NT5CC256M16ER-EK
* Flash: NAND 128 MiB F59L1G81MB-25T
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 4x 1GbE
  * Switch: SoC built-in
* USB: None
* UART: 115200 baud (labeled on board)

Load addresses (same as ipTIME AX2004M):
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* Note that the bootloader accepts both encrypted and unencrypted
  images, while the stock web interface only accepts encrypted ones.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in WAX202 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar

* openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 0f068e7c4a)
2022-07-21 16:58:18 +02:00
Thibaut VARÈNE
158a5af801
ramips: improve YunCore AX820 LEDs
At least two AX820 hardware variants are known to exist, but they cannot
be distinguished (same hardware revision, no specific markings).

They appear to have the same LED hardware, but wired differently:

- One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and
  a blue wlan5g LED at GPIO 16;
- The other only offers a green system LED at GPIO 15, with GPIO 14 and
  16 being apparently not connected

Finally, a Yuncore datasheet says the canonical wiring should be:
- Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16

All GPIOs are tied to a single RGB LED which is exposed via lightpipe on
the device front casing.

Considering the above, this patch exposes all three LEDs, preserves the
common system LED (GPIO 15) as the openwrt status LED, and removes the
color information from the LEDs names since it is not consistent across
hardware. The LED naming is made consistent with other YunCore devices.
A note is added in DTS to ensure this information is always available
and prevent unwanted changes in the future.

Fixes: #10131 "YunCore AX820: GPIO LED not correct"

Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-07-01 20:58:16 +02:00
John Audia
2b8021d614 kernel: bump 5.10 to 5.10.125
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 53d99fedc7)
2022-06-27 22:34:07 +02:00
John Audia
f2f03545d4 kernel: bump 5.10 to 5.10.124
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 9e5d743422)
2022-06-27 22:34:07 +02:00
John Audia
4faf889e7e kernel: bump 5.10 to 5.10.122
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 9edc514e3d)
2022-06-27 22:34:07 +02:00
John Audia
81530d69ef kernel: bump 5.10 to 5.10.121
Manually rebased:
    oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 706a4ec40c)
2022-06-27 22:34:07 +02:00
Tomasz Maciej Nowak
9c609080b0 generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.

Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 539e60539a)
2022-06-27 22:34:07 +02:00
Aviana Cruz
d65ad3efa5 ramips: decrease SPI frequency for Phicomm K2P
Some K2P comes with the worse boards with GD25Q128 (may be A2), which
only works with 50MHz frequency and less. Reduce spi frequency so that
these routers can boot.
remove m25p,fast-read because it isn't needed for 50MHz SPI.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 857ea3f690)
2022-06-27 19:54:12 +02:00
Arınç ÜNAL
7bc1d76419 ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFP
For a TX->TX connected external phy to transmit/receive data, the rgmii2
pin group needs to be claimed with gpio function, at least for EdgeRouter X
SFP. We already claim the pin group under the pinctrl node with gpio
function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi.

However, we should claim a pin group under its consumer node. It's the
ethernet node in this case, which we already claim the rgmii2 pin group
under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2
node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group
under the pinctrl node. With this change, we also get to remove a
definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to
EdgeRouter X SFP.

This change is tested on an EdgeRouter X SFP.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit a1ad837735)
2022-06-25 00:05:21 +02:00
Bjørn Mork
d01e374074 ramips: force ZyXEL NR7101 to boot from "Kernel" partition
Make sure BootingFlag points to the system partition we install to.

The BootingFlag variable selects which system partition the system
boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have
device specific support for this dual image scheme, and can therefore
only boot from "Kernel".

This has not been an issue until now, since all known OEM firmware
versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0.
But the newest OEM firmware has a new upgrade procedure, installing
to the "inactive" system partition and setting BootingFlag accordingly.

This workaround is needed until the dual image scheme is fully
supported.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 79112e7d47)
2022-06-25 00:05:21 +02:00
Piotr Dymacz
2726c8c315 ramips: fix booting on ZyXEL NBG-419N v2
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of other devices from 'ramips' target.

Fixes: #9842
Fixes: #8964

Reported-by: Juergen Hench <jurgen.hench@gmail.com>
Tested-by: Juergen Hench <jurgen.hench@gmail.com>
Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit fd72e595c2)
2022-06-20 11:08:36 +02:00
David Bauer
8f7e0cbebf ramips: fix RT-AC57U button level
Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the
WPS cutton to fix button behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 535b0c70b1)
2022-06-18 22:13:00 +02:00
John Audia
3ce3de934c kernel: bump 5.10 to 5.10.117
Removed upstreamed:
    backport-5.10/890-v5.19-net-sfp-Add-tx-fault-workaround-for-Huawei-MA5671A-SFP-ON.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 01a6a5c731)
2022-06-07 22:28:59 +02:00
Stijn Tintel
045fe28d4e ramips: use hotplug script for EAP615-Wall MACs
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.

Use the hotplug script for the EAP615-Wall instead to avoid this.

Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
(cherry picked from commit ce90ba1f31)
2022-06-06 11:13:26 +03:00
Hauke Mehrtens
e90f74feb6 kernel: bump 5.10 to 5.10.116
Removed upstreamed:
  generic/backport-5.10/900-regulator-consumer-Add-missing-stubs-to-regulator-co.patch

All other patches automatically rebased.

Compile-tested: lantiq/xrx200, armvirt/64
Run-tested: lantiq/xrx200, armvirt/64

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-05-18 00:16:11 +02:00
Tamas Balogh
3c57430d1c ramips: add led_source for Asus RT-AC1200 devices
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.

The dts-binding is introduced in commit:
65dc9e0980

Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
(cherry picked from commit 771ea6f2e3)
2022-05-17 21:14:46 +02:00
Alessio Prescenzo
e431195abf ramips: add support for Cudy X6
Specifications:

SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:

Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download

Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4a8eaa5c7c)
2022-05-17 21:14:46 +02:00
Andreas Böhler
5439efe37d ramips: Add support for SERCOMM NA502S
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE and audio are currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator
  - Telit UMTS module
  - Rechargeable battery
  - speaker and microphone

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9ee6ac00c4)
2022-05-17 21:14:45 +02:00
Davide Fioravanti
fe5943a7bd ramips: add support for Wavlink WL-WN533A8
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.

Hardware
--------
SoC:   Mediatek MT7621A
RAM:   128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
  - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
  - 1x MT7615NE (4x4:4) 5GHz
  - 8 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 3.0 port
UART:
  - 57600-8-N-1
    J4

Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)

Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:63 (factory @ 0xe006)
   WAN		XX:XX:XX:XX:XX:64 (factory @ 0xe000)
   WIFI 2G/5G	XX:XX:XX:XX:XX:65 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:66 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:65

   In OEM firmware the DBDC wifi interfaces have these mac addresses:
     2G) 82:XX:XX:XX:XX:65
     5G) 80:XX:XX:XX:XX:65

   While in OpenWrt the addresses are:
     2G) 80:XX:XX:XX:XX:65
     5G) 02:XX:XX:XX:XX:65

2) radio0 will show as 2G/5G interface but only 2G is really usable.

3) There is just one wifi led for all wifi interfaces.
   It currently shows only the radio0 GHz wifi activity.

4) My unit was shipped with M33A8.V5030.190716 firmware which contains
   the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
   the input box it will start the telnet daemon. Now you can access
   the telnet console on port 2323 with these credentials:
     username: admin2860
     password: admin

5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
   webcmd.shtml page. If your router is shipped with a previous firmware
   version and you want to back it up, you can follow the back up
   procedure of the WS-WN583A6.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit 32e6942d72)
2022-05-17 21:14:45 +02:00
Davide Fioravanti
5454735574 ramips: create shared DTSI for Wavlink WN53XAX devices
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit 57b6dcd826)
2022-05-17 21:14:45 +02:00
Marcin Gordziejewski
7152bc84f4 ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
  requires soldering because they're not through holes.

  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.

Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
(cherry picked from commit 39799974a3)
2022-05-17 21:14:23 +02:00
Clemens Hopfer
d627ea510c ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure:
  YunCore AX820: indoor ceiling mount AP with integrated antennas
  YunCore HWAP-AX820: outdoor enclosure with external (N) connectors

Hardware specs:
  SoC: MediaTek MT7621DAT
  Flash: 16 MiB SPI NOR
  RAM: 128MiB (DDR3, integrated)
  WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
  Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
  LED: Status (green)
  Button: Reset
  Power: 802.11af/at PoE; DC 12V,1A
  Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external

Flash instructions:
  The "OpenWRT support" version of the AX820 comes with a LEDE-based
  firmware with proprietary MTK drivers and a luci webinterface and
  ssh accessible under 192.168.1.1 on LAN; user root, no password.
  The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
  you will have to force the upgrade due to a different factory name.
  Remember: Do *not* preserve factory configuration!

MAC addresses as used by OEM firmware:
  use   address            source
  2g    44:D1:FA:*:0b      Factory 0x0004 (label)
  5g    46:D1:FA:*:0b      LAA of 2g
  lan   44:D1:FA:*:0c      Factory 0xe000
  wan   44:D1:FA:*:0d      Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.

Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
(cherry picked from commit 4891b86538)
2022-05-17 21:14:23 +02:00
Piotr Dymacz
1c6a179e1a ramips: fix booting on Samknows SK-WB8
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 064e7e57b4)
2022-05-13 13:52:58 +02:00
Felix Fietkau
77e123340f mediatek: add patches for MT7622 WED (wireless ethernet dispatch)
This series also contains other improvement for hardware flow offload support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 0f029b3d2b)
2022-05-06 19:57:57 +02:00
Alban Bedel
4c5d2cde13 ramips: zbt-wg2626: Add the reset gpio for PCIe port 1
The 2.4GHz interface doesn't come up properly with the log showing:

    mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.

Signed-off-by: Alban Bedel <albeu@free.fr>
(cherry picked from commit f953a1a4bf)
2022-05-01 11:23:43 +08:00