For the last ten years, nobody has noticed that this driver doesn't
actually say what it is for. ;)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
mutex_destroy is missing in remove.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16926
Signed-off-by: Robert Marko <robimarko@gmail.com>
Missing u caused the regulator to fail probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16925
Signed-off-by: Robert Marko <robimarko@gmail.com>
Needed to fix compilation with GCC14.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16912
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of relying on .config symbols for metadata, alter the DEFAULT
variable of affected packages. Fixes enabling opkg vs apk among others.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refactor version of spidev_test for APK.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16917
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit comes after a long period of hard work, starting back in
early 2021 as a proof of concept.
Thanks to the Alpine Linux project for creating such a nice package
manager. Thanks to everyone involved; this is going to be great!
Signed-off-by: Paul Spooren <mail@aparcar.org>
i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove backtick from gdb description text, as that seems to
be recognized as a shell action by compilation with apk,
causing error.
Example from test buildbot:
rstrip.sh: /builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/gdb-15.2/ipkg-aarch64_generic/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
bash: -c: line 2: syntax error: unexpected end of file
make[3]: *** [Makefile:123: /builder/shared-workdir/build/sdk/bin/packages/aarch64_generic/base/gdb-15.2-r1.apk] Error 2
Local compilation:
rstrip.sh: /OpenWrt/aarch64/build_dir/target-aarch64_cortex-a53_musl/gdb-15.2/ipkg-aarch64_cortex-a53/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
make[2]: *** [Makefile:123: /OpenWrt/aarch64/bin/packages/aarch64_cortex-a53/base/gdb-15.2-r1.apk] Error 2
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16908
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust wolfssl version for apk by removing the "-stable"
from the OpenWrt version, although it is still needed for
upstream download archive name.
Define PKG_BUILD_DIR accordingly.
Utilize new short version to simplify ABI_VERSION calculation.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16906
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
/sbin/pkg_check uses opkg and is not even packaged when using the
default opkg configuration. remove it when using apk too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In 451e2ce006 the code would only move packages separated by dashes,
however OPKG uses underscores to split between package name and version.
Result was the lack of such packages in the packed ImageBuilder.
Use dashes or underscores depending on the select package manger.
Fixes: 451e2ce006 "imagebuilder: fix package inclusion and APK index"
Signed-off-by: Paul Spooren <mail@aparcar.org>
These two were getting rather long.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16849
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.
This seems to break some devices where the bootloader sets it to high.
Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
The `--initdb` command creates basic folders required by APK,
previoiusly it would only run a single time when package_index is
actually called. Since the function isn't called if nothing changes,
`--initdb` doesn't initialize the rootfs again.
This commit moves it to package_reload, which runs every time.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Previously three different ways to include packages in an ImageBuilder
existed:
* buildbot: include libc, kernel (and base-files) in $(IB_LDIR)
* not buildbot, standalone: include all packages in ./packages/
* not buildbot, not standalone: include libc, kernel (and base-files) in
./packages/
First of, the separation between *buildbot* and *not buildbot, not
standalone* is not required, we can just always copy packages to
./packages instead of ever using the special place $(IB_LDIR).
Doing so drops the need to handle the extra case and also allows to
clean up the OPKG package installation, which no longer requries the
`firstword` logic, things are now always at ./packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
We need to exclude packages from the APK index which must not be
upgraded. To do so, the packages `libc`, `kernel` and `base-files` are
excluded to APK never suggestes them as upgradable.
The previous logic would however match packages like `libcomerr0`,
causing build failures. Make the copying and excluding logic more
precise by adding a single dash.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This commit solves multiple issues. First of just install the three
special packages base-files, libc and kernel directly from the index. In
upstream indexes, those will never appear to prevent accidental upgrades
may breaking the system.
Next, enable caching for the ImageBuilder, which speeds up consecutive
builds from ~33 seconds to ~5 seconds. Using cache however makes APK
create the folder `/var/cache/apk/` which conflicts with the base-files
installation, which ships a symlink from `/var` to `/tmp`, so specify
`--no-cache` for the rootfs initialization.
Lastly, drop the use of `apk update` since APK automatically does that.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This reverts commit 21b5ac862e.
The approach is flawed and cannot work in the ImageBuilder.
Using /etc/uci-defaults/ which is run on the target is the only
possible way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
vrx518_tc currently sets the interface maximum MTU to the ethernet default
of 1500 bytes by default via ether_setup() called from ptm_setup().
To support 1508 byte baby jumbo frames (RFC4638) for PPPoE connections
over VDSL links as already supported by the VR9 ltq_ptm driver ([1], [2])
set the interface maximum MTU to MAX_MTU.
MAX_MTU is defined in dcdp/inc/tc_common.h to 2002 bytes and this value is
used in ptm_change_mtu() and elsewhere as the maximum MTU, however this is
short circuited by checks against the interface maximum MTU.
[1]: https://forum.openwrt.org/t/fritzbox-7530-and-rfc4638-baby-jumbo-frames/181327
[2]: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=8a2a20e71e2909f84dab47e51dfda9e292a6c1ae
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/16856
Signed-off-by: Robert Marko <robimarko@gmail.com>
IMAGE_SIZE was previously set to kernel1 + ubi size = 256768k, now
kernel1 is 6MB adjust this value to add 3072k to total image size.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.
Re-enable image builds for Edgerouter-X and X-SFP.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refer user to the wiki page for instructions on how to migrate to the
new kernel layout.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Uboot selects which kernel slot to boot based on a flag in the factory
mtd partition. Patch ubnt.sh to ensure always flash to kernel1 slot and
update flag if required.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The OEM layout for Edgerouter X provides for two 3MB kernel slots.
As of linux 6.1 the kernel images no longer fit and as such
Edgerouter X builds have been disabled in Main.
Revise the layout to make kernel1 slot 6MB and drop kernel2 slot.
This patch applies the required changes to the dts file.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
Signed-off-by: Petr Štetiar <ynezz@true.cz>
e93f6c3fc729 main: fix format string related warnings for log/debug printf functions
6ab44a2413f9 fix signed/unsigned comparison warnings
4fe997b61d7d system-dummy: add system_if_apply_settings_after_up
992d33cb42a6 ubus: add notifications on wireless device state changes
34eb11eb6f5c device/interface: add "tags" attribute from config to status dump
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
post-install scripts may need to call executables installed to
STAGING_DIR_HOSTPKG which is not part of the PATH set to TARGET_PATH in
rules.mk.
Set PATH for post-install scripts to TARGET_PATH_PKG.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/16865
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
