This is a backport of the upstream commit 58bbbb598144 ("nl80211: Ignore
4addr mode enabling error if it was already enabled") which fixes same
issue as in the current fix contained in '130-wpa_supplicant-multi_ap_roam.patch',
but in a different way:
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
[bump PKG_RELEASE, more verbose commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch is required to be able to roam from one backhaul AP to
another one in the same ESS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: PKG_REVISION bump and refreshed patches)
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This patch allows other applications to get events management
frames (for example: association requests).
This is useful in Multi-AP context to be able to save association
requests from stations.
It has been sent to upstream hostapd in this series:
https://patchwork.ozlabs.org/project/hostap/list/?series=217500
'700-wifi-reload.patch' is updated due to the introduction of
'110-notify-mgmt-frames.patch'.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
Commit 7c8c4f1be6 ("hostapd: fix P2P group information processing
vulnerability") was missing the actual patch for the vulnerability.
Fixes: 7c8c4f1be6 ("hostapd: fix P2P group information processing vulnerability")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
'base' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
'enc_str' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Granting capabilities CAP_NET_ADMIN and CAP_NET_RAW allows running
hostapd and wpa_supplicant without root priviledges.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables hostapd.sh to properly configure wpa_supplicant
for when GCMP is used as cipher in station mode.
Without this wpa_supplicant will be unable to connect to AP.
This is needed for wil6210 as it does not support CCMP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds an option "hostapd_bss_options" that does the same as
"hostapd_options" but on a per-BSS level, instead of a per-device level.
This can be used, for example, to configure different per-devce sae_passwords
per BSS or to augment some of the existing per-BSS options.
Signed-off-by: Florian Beverborg <flo@beverb.org>
[remove whitespace errors, bump release]
Signed-off-by: Paul Spooren <mail@aparcar.org>
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.
It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.
As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
When hostapd gets restarted to often/quickly will cause procd to not restart it
anymore. it will think that hapd is in a crash loop.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
Currently, EAPOLv2 (802.1X-2004) is used by default for legacy clients that
are not WPA2 (RSN) capable. These legacy clients are often intolerant to this
EAPOL version and fail to connect.
hostapd.conf upstream documents for eapol_version the following and that this
is a known compatibility issue with version 2:
// IEEE 802.1X/EAPOL version
// hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL
// version 2. However, there are many client implementations that do not handle
// the new version number correctly (they seem to drop the frames completely).
// In order to make hostapd interoperate with these clients, the version number
// can be set to the older version (1) with this configuration value.
// Note: When using MACsec, eapol_version shall be set to 3, which is
// defined in IEEE Std 802.1X-2010.
//eapol_version=2
For the wpa parameter, hostapd.conf upstream documents that this is a bitfield,
configured as follows:
// Enable WPA. Setting this variable configures the AP to require WPA (either
// WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
// wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
// Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice.
// For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
// RADIUS authentication server must be configured, and WPA-EAP must be included
// in wpa_key_mgmt.
// This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)
// and/or WPA2 (full IEEE 802.11i/RSN):
// bit0 = WPA
// bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
// Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2.
// In other words, for WPA3, wpa=2 is used the configuration (and
// wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK).
//wpa=2
For client compatibility therefore:
EAPOLv1 (802.1X-2001) should be used by default where WPA is enabled.
EAPOLv2 (802.1X-2004) should be used by default where WPA is disabled.
To fix this, we can therefore change in the script:
set_default eapol_version 0
To the following:
set_default eapol_version $((wpa & 1))
This therefore:
1) Sets eapol_version to 1 where WPA has been enabled via wpa bit0 being set.
2) Sets eapol_version to 0 where WPA has been disabled via wpa bit0 being unset.
For usual configurations that only have WPA2 enabled, EAPOLv2 is then used.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
hostapd.sh does not parse skip_inactivity_poll boolean from
/etc/config/wireless despite being mentioned in the documentation [1].
This change fixes this, and by default sets its value to 0 [1].
[1] https://openwrt.org/docs/guide-user/network/wifi/basic
Signed-off-by: Nadim Atiya <nadim.atiya@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[fix and reformat commit message, make patch apply]
Set legacy_rates to 0 by default to disable 802.11b data rates by default.
The time has long come where 802.11b DSSS/CCK data rates should be disabled
by default in OpenWRT. Users in need of 802.11b client support can reasonably
enable these where they are needed.
The balance of equities has significantly, and for a long time, tipped
such that dropping backwards compatibility by default with 802.11b
devices is appropriate, proportionate and justified. By doing so,
management and control traffic is moved by default to a 20
MHz wide 6 Mb/s OFDM data rate instead of a 22 MHz wide 1 Mb/s DSSS data
rate. This is significantly more airtime efficient.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Add a cell_density option to configure data rates for normal, high and
very high cell density wireless deployments.
The purpose of using a minimum basic/mandatory data rate that is higher
than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density
environments is to transmit broadcast/multicast data frames using less
airtime or to reduce management overheads where significant co-channel
interference (CCI) exists and cannot be avoided.
Caution: Without careful design and validation, configuration of a too
high minimum basic/mandatory data rate can sacrifice connection stability
or disrupt the ability to reliably connect and authenticate for little to
no capacity benefit. This is because this configuration affects the
ability of clients to hear and demodulate management, control and
broadcast/multicast data frames.
Deployments that have not been specifically designed and validated are
usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data
rates.
Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b
compatible), minimum basic/mandatory rate in high cell density
deployments that have been designed and validated for this.
For many deployments, the minimum basic/mandatory data rate should not be
configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a
configuration is only appropriate for use in very high cell density
deployment scenarios.
A cell_density of Very High (3) should only be used where a deployment
has a valid use case and has been designed and validated specifically for
this use, nearly always with highly directional antennas - an example
would be stadium deployments. For example, with a 24 Mb/s OFDM minimum
basic/mandatory data rate, approximately a -73 dBm RSSI is required to
decode frames. Many clients will not have roamed elsewhere by the time
that they experience -73 dBm and, where they do, they frequently may not
hear and be able to demodulate beacon, control or broadcast/multicast
data frames causing connectivity issues.
There is a myth that disabling lower basic/mandatory data rates will
improve roaming and avoid sticky clients. For 802.11n, 802.11ac and
802.11ax clients this is not correct as clients will shift to and use
lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are
able to be used as basic/mandatory data rates.
There is a myth that disabling lower basic/mandatory data rates will
ensure that clients only use higher data rates and that better
performance is assured. For 802.11n, 802.11ac and 802.11ax clients this
is not correct as clients will shift around and use MCS rates and not the
802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory
data rates.
Cell Density
0 - Disabled (Default)
Setting cell_density to 0 does not configure data rates. This is the
default.
1 - Normal Cell Density
Setting cell_density to 1 configures the basic/mandatory rates to 6, 12
and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting cell_density to 1 configures the basic/mandatory rates to the 5.5
and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower
than the minimum basic/mandatory rate are not offered.
2 - High Cell Density
Setting the cell_density to 2 configures the basic/mandatory rates to the
12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting the cell_density to 2 configures the basic/mandatory rates to the
11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the
minimum basic/mandatory rate are not offered.
3 - Very High Cell Density
Setting the cell_density to 3 configures the basic/mandatory rates to the
24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the
minimum basic/mandatory rate are not offered.
Setting the cell_density to 3 only has effect where legacy_rates is 0,
else this has the same effect as being configured with a cell_density of 2.
Where specified, the basic_rate and supported_rates options continue to
override both the cell_density and legacy_rates options.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Several variables in hostapd.sh can be used uninitialized in numerical
comparisons, causing errors in logread:
netifd: radio24 (1668): sh: out of range
Set defaults for those variables to silence those errors.
Fixes: b518f07d4b ("hostapd: remove ieee80211v option")
Fixes: cc80cf53c5 ("hostapd: add FTM responder support")
Fixes: e66bd0eb04 ("hostapd: make rrm report independent of ieee80211k setting")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixes the offset of the patch added in 93bbd998aa
("hostapd: enter DFS state if no available channel is found").
Signed-off-by: Leon M. George <leon@georgemail.eu>
This sets the validity interval for the BSS transition candidate
list to the same value as the disassociation timer.
Currently the value is always 0, which is the specification states is a
reserved value. Also, wpa_supplicant and from the looks of it some
Android implementations will outright ignore the candidate list in this
case.
Signed-off-by: David Bauer <mail@david-bauer.net>
* Add support for passing airtime_sta_weight into hostapd configuration.
* Since that commit it is possible to configure station weights. Set higher
value for larger airtime share, lower for smaller share.
I have tested this functionality by modyfing /etc/config/wireless to:
config wifi-device 'radio0'
...
option airtime_mode '1'
config wifi-iface 'default_radio0'
...
list airtime_sta_weight '01:02:03:04:05:06 1024'
Now, when the station associates with the access point it has been assigned
a higher weight value.
root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime
RX: 12656 us
TX: 10617 us
Weight: 1024
Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us
[MAC address has been changed into a dummy one.]
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
airtime_mode is always parsed as an empty string since it hasn't been
added into hostapd_common_add_device_config function.
Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration")
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
This adds a new get_status method to a hostapd interface, which
provides information about the current interface status.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds information from mac80211 to hostapd get_client ubus function.
This way, TX as well as RX status information as well as the signal can
be determined.
Signed-off-by: David Bauer <mail@david-bauer.net>
If only AP mode is needed, this is currently the most space-efficient way to
provide support for WPA{2,3}-PSK, 802.11w and 802.11r.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin sizes:
4719426 bytes (with wpad-basic-wolfssl)
4457282 bytes (with hostapd-basic-wolfssl)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hotspot 2.0 AP features have been made available in the -full variants
of hostapd and wpad. Hence we no longer need a seperate package for
that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add OpenSSL-linked basic variants (which provides WPA-PSK only, 802.11r and
802.11w) of both hostapd and wpad. For people who don't need the full hostapd
but are stuck with libopenssl for other reasons, this saves space by avoiding
the need of an additional library (or a larger hostapd with built-in crypto).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds missing config symbols for interworking as well as Hotspot 2.0
to the wpa_supplicant-full configuration.
These symbols were added to the hostapd-full configuration prior to this
commit. Without adding them to the wpa_supplicant configuration,
building of wpad-full fails.
Thanks to Rene for reaching out on IRC.
Fixes: commit be9694aaa2 ("hostapd: add UCI support for Hotspot 2.0")
Fixes: commit 838b412cb5 ("hostapd: add interworking support")
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds configuration options to enable interworking for hostapd.
All options require iw_enabled to be set to 1 for a given VAP.
All IEEE802.11u related settings are supported with exception of the
venue information which will be added as separate UCI sections at a
later point.
The options use the same name as the ones from the hostapd.conf file
with a "iw_" prefix added.
All UCI configuration options are passed without further modifications
to hostapd with exceptions of the following options, whose elements can
be provided using UCI lis elements:
- iw_roaming_consortium
- iw_anqp_elem
- iw_nai_realm
- iw_domain_name
- iw_anqp_3gpp_cell_net
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds support for enabling the FTM responder flag for the APs
extended capabilities. On supported hardware, enabling the ftm_responder
config key for a given AP will enable the FTM responder bit.
FTM support itself is unconditionally implemented in the devices
firmware (ath10k 2nd generation with 3.2.1.1 firmware). There's
currently no softmac implementation.
Also allow to configure LCI and civic location information which can be
transmitted to a FTM initiator.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove the ieee80211v option. It previously was required to be enabled
in order to use time_advertisement, time_zone, wnm_sleep_mode and
bss_transition, however it didn't enable any of these options by default.
Remove it, as configuring these options independently is enough.
This change does not influence the behavior of any already configured
setting.
Signed-off-by: David Bauer <mail@david-bauer.net>
Allow to configure both RRM beacon as well as neighbor reports
independently and only enable them by default in case the ieee80211k
config option is set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is useful to bring up multiple client mode interfaces on a single
channel much faster without having to scan through a lot of channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make the BSSID and SSID fields optional when configuring a neighbor
report into hostapd.
Both options can now be an empty string. For the BSSID, the first 6 byte
are copied from the neighbor report. For the SSID, the SSID for the
affected hostapd BSS is used.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafal Milecki pointed out that ubus events are meant for low-level ubus
events only (e.g. addition or removal of an object). Higher level
events should happen as notifications on the ubus object itself.
Dispatch BSS events on the main hostapd ubus object instead of
publishing them as ubus events.
Signed-off-by: David Bauer <mail@david-bauer.net>
