Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
Wave-1 firmware has a fix for 'addba' not finding the peer. Thanks to Hauke
for finding and reporting this.
Wave-2 firmware has a fix for leaking a peer multicast key when a monitor device
is created.
And I re-ordered the '4019' firmware images in the Makefile to match the order
of the others. No functional change for that reorder.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
The HTT-MGT variants transport management frames over the
normal HTT tx path, just like data frames. This saves
limitted WMI buffers which can become depleted if lots of
management frames become stuck in TX queues due to peer
that went away.
In addition, at least for the wave-1 firmware, htt-mgt is
required in order for 802.11r (fast roaming) authentication
to function properly.
The htt-mgt firmware requires the use of the ath10k-ct
driver. Normal non-htt-mgt ath10k-ct firmware should work
with stock drivers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This updates to latest ath10k-ct firmware. Hopefully we are
at the end of the development cycle for this firmware release,
so these should be stable.
wave-1 changes since last release:
Release 20
* Allow flushing peer when deleting. Hopefully this will allow the
peer delete command to happen in a reasonable amount of time even
if the RF environment is busy (or peer has died).
To enable this, set the high flag in the mac-addr second word in the
ath10k driver near end of the ath10k_wmi_op_gen_peer_delete method:
cmd->peer_macaddr.word1 |= __cpu_to_le32(0x80000000);
* Attempt to fix crash seen in resmgr-ocs, appearantly due to list corruption.
Use a temporary list instead of trying to rely on for-each-safe.
* Add flag to tx-descriptor to allow driver to request no-ack on data
frames. This is bit 15 on the flag1 field (previously un-used).
* Add option to support specifying the tx-rate-code and retry count on
a per-packet basis. Only a single series is supported at this time.
Useful mainly for radiotap monitor-tx type testing at this point.
* Fix crash on startup when chip is at -40 deg C and calibration fails. Instead
of asserting, just keep retrying calibration, which appears to start working
after a few minutes (when the chip warms up).
* Allow reporting per-chain rssi for management frames. We pack the values into
empty space in the mgt-frame wmi header. This will only be enabled if the driver
requests it, since otherwise the driver is assumed to not understand the new API.
ath10k-ct drivers that support this feature will automatically enable it.
* A customer reports a case that appears to be the hardware not properly detecting
end of AMPDU, so frames were being mis-delivered to the wrong peer. Attempt to
work around this, and in doing so, clean up a bunch of void* abuse in the block-ack
reordering code (could not ever confirm there was a problem in this area).
* Re-work the rx-mem logic to be less complicated and to use less memory.
* Attempt to fix crash that appearanty happens because the driver can sometimes
delete a vdev in 'up' state.
* Attempt to fix hung scan state machine issues.
* Fix crash in tx path due to un-initialized memory.
wave-2 changes since last release:
Release 10
* Fix an assert related to tx scheduling. This hopefully fixes
what appears to be a regression that I added some time back.
* Enable CSI reporting for 9984, and maybe 9888/9886. Only in
non-trimmed builds.
* Other stability improvements, including regression fixes from
some tricky bugs introduced in earlier releases.
* Allow compiling for IPQ4019 chipset.
* Firmware will now send txbf frames to the host (driver) if the
TXBF (0xF00000001) set-special feature is enabled, or when the radio
is in monitor mode. But, if the frame is consumed by the txbf_cv
logic, then the pkt cannot be delivered to the host in this manner. Instead,
a WMI event will be sent and host can find the txbf_cv data in shared
memory. See ath10k_wmi_event_txbf_cv_mesg() in ath10k-ct driver.
* Support rx-all-mgt option. When enabled, the firmware will deliver all
management frames that it can to the host. No RX filters are changed
when this option is enabled.
* Fix at least some problems with sending tx-beamforming frames to SU-MIMO
peers. Looks like this was a regression in my code.
* Fix a crash in rate-ctrl due to nss mismatch. This was something I introduced
while trying to fix other bugs in rate-ctrl some time back.
* Attempt to fix a sw-peer-key object leak in IBSS mode. The peer key code
is very complex, and shares some pointers as union members. I think I fixed
at least some of the issues, but would not be surprised if more exist.
* Improve ath10k user guide to document CT firmware features:
https://www.candelatech.com/ath10k-ug.php
* Add ct-special option to configure the txbf sounding time. See ath10k-ug.php
* Fix and allow the driver to tell the firmware to send sounding frames. See ath10k-ug.php
In further testing, this seems to fail much of the time, and I am not sure why.
Disabling this in diet (trimmed) builds.
* Fix crashes related to deleting peers while they are in power-save mode. Reported
by LEDE user on r7800 with 9984 NIC.
* Make rate-ctrl txbf probe work better. If enabled, the rate-ctrl logic will periodically
send out probes at an NSS that can to txbf. Previously, txbf probes would not reliably happen
if both AP and peer had the same nss (ie, 2x2 talking to 2x2). To enable this feature, you
need to enable the fwtest-cmdid number 20.
* Report rx-timeout error counters. These were previously un-reported, though the
field existed in the wmi struct already.
* txbf: Ignore frames not destined for us. If NIC is in promisc mode, it
could acquire and process NDPA frames that were not destined for it. Check
the dest-MAC and ignore frames not for us (pass them up the stack for monitor
mode instead of save them in the peer's rate-ctrl logic.)
* Port ping-pong crash handling and othe related features to IPQ4019 target. It should
now act similar to 9984 in this regard.
* Fix a few asserts related to txbf and tx-seq logic.
* Add custom-stats support, for rx-reorder-stats. Similar to what I did for wave-1.
* Disable AMSDU for IBSS. This now matches what I did for peregrine. It seems to
work better this way, though I did not debug it in detail.
* Enable the set-special command to re-enable AMSDU for IBSS if user wants to experiment.
* Fix bug where dbglog did not disable IRQs, so if you made dbglog messages from the IRQ
handler, it could cause corruption that could crash the firmware and/or corrupt the log
message buffers.
* Don't assert if there are no buffer descriptors for RX of non-data frame.
* Retry any stuck block-ack sessions every 20 seconds instead of just disabling BA for
ever when we get too many failures.
* Fix SGI flag when reporting tx-rate info. The flag moved since wave-1 days, and
I did not notice that when I ported my changes forward to wave-2.
* Allow disabling special CCA handling for IBSS txqs. Earlier testing indicated this
might improve throughput in some testing on 9984 chips in IBSS mode, but subsequent
testing looks about the same without it. Since I do not really understand what this
setting exists for, leave it at upstream defaults. A new set-special API command (0x12)
can be used to enable this hack for testing. Setting 0x1 bit disables special CCA handling
for non-beacon IBSS txqs, setting 0x2 bit disables it for beacon queues as well.
* Add MCAST-BCAST feature flag. This tells driver we do not need a monitor interface
to do MESH.
* When calculating the rx-address filter (affects ACK & BLOCK-ACK, among other things),
to not add in monitor interfaces if other interfaces are up. There is no need for
a monitor device to ACK frames.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Update DEPENDS and PROVIDES so that ath10k-ct firmware
and drivers can be used to replace stock firmware
and drivers. The -htt firmware variant, which requires
ath10k-ct driver now selects ath10k-ct driver when the
firmware is selected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Updated ppfe firmware to NXP LSDK1712 release. Used
ppfe firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NXP LSDK1712 release used two rcw git trees. The
original rcw git tree was still source code but
dropping ls1012a/ls1088a/ls2088a boards in LSDK1712.
Instead another new rcw git tree was used to just
provided rcw binaries for these boards dropped. So
this patch is to update ls-rcw to LSDK1712 release
and add a new ls-rcw-bin package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
fman-ucode had been migrated from qoriq-open-source
github to NXP github. So the Makefile should be fixed
accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated MC firmware to NXP LSDK1712 release. Used
MC firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* introduces the BDFs for the OpenMesh A42 in
/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
QCA6174 hw3.0
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.
x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the Debian repository for sourcing the ucode files.
Current (20171205) includes support for fam17h CPUs already.
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA988x.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA9887.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9888.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9984.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA4019.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This update automatically includes a new firmware for the QCA6174:
firmware-6.bin_WLAN.RM.4.4.1-00079-QCARMSWPZ-1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
PKG_BUILD_DIR was defined with quoting PKG_VERSION in
layerscape package makefiles. Now PKG_VERSION has been
removed from these makefiles. When PKG_BUILD_DIR quotes
PKG_VERSION, '=' should be used instead ':=' to make
sure PKG_VERSION has been defined in common makefile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.2.1-00058 firmware for the QCA4019.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
layerscape firmware package names collide with existing package contributions.
Ex: layerscape mc and midnight-commander(mc) are in conflict.
Firmware packages: mc, ppa, rcw and dpl are renamed to ls-mc, ls-ppa, ls-rcw
and ls-dpl respectively.
Signed-off-by: Ted Hess <thess@kitschensync.net>
The firmware directory in the Linux kernel was removed in kernel 4.14,
take the e100 firmware files now from the linux-firmware repository
instead. To do so create the new package e100-firmware. This will also
work with older kernel versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
make check complains about PKG_MIRROR_HASH of the wireless-regdb package:
WARNING: PKG_MIRROR_HASH does not match wireless-regdb-2017-10-20-4343d359.tar.xz
hash 5f5b669f32ae36cb65b1d99efbbbfd42c2983cda32f6448346e3e54ffaba3889
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add data path layout files for the
second generation Data Path Acceleration Architecture.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add package support for Management
Complex Firmware for the second generation Data Path
Acceleration Architecture.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Changes since last LEDE release include:
* Fix key-setting bug that broke sending the EAPOL 2/4 in some cases. This was a
bug I introduced some time back while trying to fix .11r and simplify the key
handling logic. (Patch to wpa_supplicant fixed the race with sending the 4/4
and setting the key...un-patched supplicant will still have this race and the 4-way
auth will not work as reliably.)
* Increase amount of active-tids that can be scheduled. This fixes a tx-stall
seen with many station vdevs.
* Fix bug in upstream code that would cause the maximum peer to never be scheduled
for tx.
Signed-off-by: Ben Greear <greearb@candelatech.com>
NXP Layerscape LSDK had set up its own open source web site
and github for release.
https://lsdk.github.iohttps://github.com/qoriq-open-source
This patch is to update rcw/fman_ucode/u-boot packages with LSDK
git trees. Also add some patches of packages to support LEDE.
Since ARMv8 32-bit u-boot images are same with ARMv8 64-bit images
but 64-bit toolchain couldn't be used for 32-bit targets, we still
use a private tree for ARMv8 32-bit u-boot images. This is in plan
to move this private tree to NXP Layerscape github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Instead of manually downloading the files again we can also take the
same files directly from the ath10k-firmware git which was cloned
before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not create one big package with all the Intel firmware files
supported by the iwlwifi driver, but use a separate package for each
chip.
This also updates some 7000 and 8000 series firmware files to more
recent version. The older versions shipped are not supported by the
current driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
update firmware mrvl/sd8887_uapsta.bin
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[update to version 2017-09-06]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ath10k-firmware: add qca9888 firmware
the firmware files for qca9888 were previously not packaged. add the meta
information for doing so.
Signed-off-by: John Crispin <john@phrozen.org>
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.
Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).
Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This firmware shoul have the same general feature set as the
rest of the 10.4 CT firmware (9984, 9980, etc). Build-tested
only in LEDE, but firmware has been tested with ath10k-ct driver
on other OSs, so likely works just fine.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The 988x and 9887 firmwares include a bugfix for a case where blockack
did not work sometimes, and many fixes for compiler warnings detected
by newer gcc compilers.
The 9980 and 9984 firmware includes a large backport of upstream QCA
firmware changes to bring it up to date.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
update the qca988x firmware to firmware-5.bin_10.2.4-1.0-00029.
According to LEDE Forum, the new firmware supports mesh mode.
Also, it seems to have several improvements.
Signed-off-by: Changmin Jang <ckdalsdk12@gmail.com>
Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On the ath10k-devel ML Michael Kazior stated:
"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].
Later on Rajkumar Manoharan explained:
"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.
|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data
Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.
Currently, the solution for this problem is to supply a
custom board-2.bin for every device.
To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
location, there can only one board overwrite installed
at any time. (All packages CONFLICT with each other.
It's also not possible to "builtin" multiple package.)
2. updating ath10k-firmware-qca4019 will also replace
the board-2.bin. For this cases the user needs to
manually reinstall the wifi-board package once the
ath10k-firmware-qca4019 is updated.
To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Fixes firmware crash in rare cases and a bug
ath10k_pci 0001:01:00.0: received unexpected tx_fetch_ind event: in
push mode
for those who kept experiencing it after previous firmware update.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
And, update support for 9880 chipsets. The new firmware
fixes a regression with EAPOL 4/4 packets added in
a recent commit.
It also fixes a case where the firmware would improperly try
to use STBC when configured for 1x1 (as 9887 always is).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch updates the QCA988X firmware to the latest revision
firmware-5.bin_10.2.4-1.0-00016
found in the official ath10k-firmware repository.
Tested on TP-Link Archer C7 v2.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
For 988X, 9980, 9984 CT firmware.
This should allow IBSS + RSN on at least the 988X firmware,
and includes recent stability fixes for all firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Current board-2.bin file for qca9984 in Kvalo's repo is from branch
10.4-3.2, while board-2.bin file in code-aurora repo is newer and
corresponds to the branch 10.4-3.3, the same as recently updated firmware.
Considering that it's better to have all parts from the same branch
we are updating board-2.bin as well.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
bnx2 driver support for the x86 architecture. Includes module and
firmware for Broadcom BCM5706/5708/5709/5716 ethernet adapters.
Signed-off-by: George Amanakis <g_amanakis@yahoo.com>
This reverts commit 0d4f02dfd6, which was
obviously untested. git downloads cannot handle multiple URLs at the
moment.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A new firmware that is available on code-aurora repository is newer
than in Kvalo's repo.
Taking into account that firmwares that are in Kvalo's repo are considered
to be tested by internal QCA team, this one seems to be more stable
and fixes this bug:
ath10k_pci 0000:01:00.0: received unexpected tx_fetch_ind event: in
push mode
At least i havent faced it for a while in contradiction to current version.
Thus switching firmware source for qca9984 until it or a newer version
gets into Kvalo's repo.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Add .cis firmware for Sierra Wireless Aircard GPRS/3G PCMCIA modems:
- Aircard 555
- Aircards 7xx
- Aircards 8x0
There is a package named sierra-pcmcia in obsoleted repository for
packages at git.openwrt.org but there's no reason to reintroduce it in
current packages repo because these files are part of upstream
linux-firmware.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
CT firmware files use the same filename with a different URL for
different chips. Since all files end up in dl/, filenames need to be
unique as well.
Add a chip prefix to the output filename to fix this issue.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this package references an undefined variable for its submenu.
Remove this NOP variable assignment.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
The 10.1 includes a good many stability fixes related to the effort of
backporting upstream 10.2 firmware. Also enables 802.1q vlan support.
Successfully tested on apu2.
The 10.4 firmwares including new backported code as well as stability
fixes. 10.4 has been tested on Fedora x86-64 platforms, but not on LEDE
specifically since I had issues compiling LEDE for my 9980/9984 AP hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
* Backport much of the 10.2 firmware features from upstream QCA driver.
This includes ANI support, adaptive CCA, tx-hang workarounds,
and lots of other things.
Not all of this may be enabled at this point, and more code waits to
be backported as time and motivation allows.
* Fix some rate-control issues where ath10k in station mode (at least), would
sometimes get stuck at low rates. This appeared to be a probe related
state machine issue in the firmware, so I added some timeout logic to kick
the state machine if it gets stuck. This signicantly improves throughput
tests with many stations.
* Support configuring WMI WD timeout using SET_SPECIAL API.
* Properly configure the rx-mask on bootup to work around problem found
by Mr. Kazior. This should remove the need to add the driver hack he
posted.
* Allow configuring pdev failed-retry threshold. This is how many consecutive
tx failures the firmware will allow before resetting the wifi chip (not a full
firmware crash).
Signed-off-by: Ben Greear <greearb@candelatech.com>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch moves the ath10k firmware packages to the firmware submenu
in the buildroot, where it belongs.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Use firmware version 10.2.4.70.54 from kvalo's git repository. The old
version (even though it's version number is greater) is an old version
from September 2015.
Using only the firmware versions from kvalo's git repo is recommended,
because those are tested by QCA's internal QCA.
The QCA988X directory received a small reorganization as a "hw2.0"
subdirectory was added - this patch also takes care of that as
board.bin was moved to that subdirectory.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Adds Google's mirrors as primary source and kernel.org as fallback.
Discussed in #lede-dev on Freenode
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update the linux-firmware package in order to force the buildbots to fetch the
proper mirrored version.
Currently each builder has its own copy of the linux-firmware checkout staged
in its own dl/, since the package was updated before the mirrored copy has
been uploaded. The builders then subsequently uploaded their own copy instead,
leading to md5sum mismatches since each clone produces different tarballs.
By bumping the package to a new version and uploading the mirrored archive
with the proper md5sum beforehand, the builders will fetch that instead and
not upload their own copies.
To properly solve that problem in the future we need to ensure that packed
checkouts become reproducable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since the md5sum of the mirrored Git clone archive has been set in the Makefile
before that particular archive was uploaded to the source mirror, the buildbots
uploaded their own, different copy instead invalidating the mirror md5sum for
anyone else.
In order to fix the mismatch, update the md5sum to reflect the archive being
present on the download server.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Annex A firmware will be updated to:
05.08.01.08.01.06_05.08.00.0B.01.01_osc
The Annex B firmware will be updated to:
05.07.09.09.00.06_05.07.04.04.00.02_osc
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Using few packages will allow saving some space by decreasing rootfs
size.
Moreover there are more firmware files that may require packaging and
even more to come later.
This can especially useful now, with per device rootfs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Using few packages will allow saving some space by decreasing rootfs
size. Dropping 43602a1 firmware saves 316 580 B. Dropping 4366b1 saves
468 188 B.
Moreover there are more firmware files that may require packaging and
even more to come later (e.g. 4366c0).
This can especially useful now, with per device rootfs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested briefly on Netgear r7800. Firmware failed to load on first
boot, but then it worked after that and I could not reproduce the
failure.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Among other things, this compiles out support for peer caching.
The feature did not seem to work well in my testing of AP mode,
and totally breaks my own special use of station mode.
Briefly tested on ea8500.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This firmware has been lightly tested on non LEDE system
to date, and will be undergoing further testing and development.
Allow users to easily install this on their LEDE system as
they prefer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This lets one use the CT ath10k driver instead of the built-in
ath10k driver from the upstream kernel (or backports).
This should be a drop-in replacement, as well as enabling
better CT firmware support.
Signed-off-by: Ben Greear <greearb@candelatech.com>
There are multiple prism54/p54 firmware versions for different
drivers and devices. Therefore, assigning the package version
of all the different firmware packages on the old prism54
firmware could break if any of the p54 firmwares are updated
and we need to roll out new packages.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed PKG_VERSION]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use first caldata for devices without OTP. The driver uses the caldata
instead of the board.bin data anyway
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of downloading the firmware for prism54 devices in the
wireless.mk do it in an extra package Makefile. To ship the complete
source code Intel ships our modified OpenWrt/LEDE + the content of the
dl directory. We do not want to have any files in the dl/ directory
which are not needed to build our images. The prism54 gets downloaded
every time independently of building kmod-net-prism54 or not. When it
is in a own package it only gets downloaded when the firmware package
is selected.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
The copy on the mirror has a different md5sum as specified in this
package Makefile. The content of the file on the mirror is the same as
in the checkout so just update our md5sum.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of downloading the firmware from some website take it from
linux-firmware package and do not download it separately any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Original URL got 303 redirect which then also dropped the commit id
leading to different file revision & MD5 mismatch.
Corrected URL & clarified commit ID use in Makefile
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This allows one to select CT firmware for ath10k
if one prefers to try this firmware instead of stock
ath10k firmware.
The 10.1 (988X) firmware can actually be installed beside the
default firmware, but it will not be used as long as the firmware-5.bin
file exists. Users could rename the files and reboot to use different
images.
The 99X0 (wave-2) firmware uses the same firmware-5.bin name as default
firmware, so it cannot be installed at the same time as default firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Add nonshared flag to package depending on specific targets or subtargets as
there's no guarantee otherwise that they'll be available in the shared repo.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds the firmware needed for the BCM43438 included in Raspberry Pi 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 49102
Some parts of this package were named rt73-pci-firmware before which
looks like a copy and past error. This renames all parts to rt73-usb-
firmware and then the firmware gets build and the dependencies from the
package with the kernel module are also working correctly.
This fixes#22069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49037
Instead of having two big binaries only add one binary and then a patch
to create the other one when needed at runtime.
This is easier to handle in one Makefile for both firmware files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48939
This adds option to build kernel module and firmware packages
for a Marvell 8686 SPI Wireless device
Signed-off-by: Joseph Honold <mozzwald@gmail.com>
SVN-Revision: 48750
This just renamed the package to indicate that this is the annex a version.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47649
Updates the ath10-firmware release to current git and updates the
QCA988X firmware in use to version 10.2.4.70.12-2 which appears to
actually fix the stability problems when using a Nexus 5X phone as
per issue #20854. Also updates the Makefile for a change in the
location of the board.bin file for QCA988X in the source repository.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 47469
Updates the ath10k firmware version for QCA988X to version
10.2.4.70.10-2, which appears to fix problems with the 5GHz wireless
failing on TP-Link Archer C7 v2 when using a Nexus 5X phone. Fixes
issue #20854.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 47454
