Add back support for the TLC591xx series LEDs which are used in the
ipq806x-based Meraki Cryptid series devices.
This module previously existed for the mvebu platform but was removed
at commit f849c2c832 due to being enabled
in that platform's kernel config.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
When loading the bonding driver, bonding interface are automatically
created on bonding module load.
> ip a s bond0
> 14: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
> group default qlen 1000
> link/ether a6:f2:20:64:c1:b9 brd ff:ff:ff:ff:ff:ff
This is not necessary in openwrt as we do not use this created interface.
The netifd creates a bonding interface based on its network configuration
name and configures this over the netifd bonding proto handler.
In order to keep the overview of the interfaces clear, bonding
interfaces should not be created automatically when loading this module,
because they are not used anyway.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The GPIO_DEVICE symbol belonged to a custom driver that was removed from
OpenWrt in 2012. The symbol never existed in the upstream kernel.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Even though TRACEPOINTS is not enabled in my kernel config, my build
fails due to KVM_MMU_AUDIT being missing. Add this symbol to kmod-kvm to
fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The xfrm_interface module will not be built if IPv6 is not enabled in
the kernel. Add this dependency in the kmod package to avoid people
wondering why it doesn't build when they disabled IPv6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When the kmod-qlcnic package is built on targets that have
CONFIG_PCI_IOV enabled, the CONFIG_QLCNIC_SRIOV symbol is exposed.
Enable this symbol in the kmod package to fix its build.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on
devices with pci support.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Without loading the igb at boot, the recovery wouldn't have
network available. All network drivers should be loaded before
etc/board.d/02_network is called. Note that other network drivers
already have this set, such as tg3.
Fixes: 7e0e5110bc ("kernel: add igb kernel module")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_CRYPTO_DEV_TALITOS depends on FSL_SOC. This driver only makes sense
on Freescale(NXP) SoCs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_DEV_GEODE depends on X86_32. This driver only makes sense
on X86\geode.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_PCOMP and CONFIG_CRYPTO_PCOMP2 have been removed in upstream commit[1].
This symbol doesn't exist since kernel 4.6 and this package is empty.
1. [ crypto: compress - remove unused pcomp interface ]
(110492183c)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_WORKQUEUE was removed in upstream commit[1]. This symbol doesn't
exist since kernel 5.3 and this package is empty.
1. [ crypto: cryptd - move kcrypto_wq into cryptd ]
(3e56e16863)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Adds support for LEDs on input devices. Useful for example on x86 laptops-
allows re-purposing num/caps/scroll lock LEDs.
Signed-off-by: Anderson McKinley <coyoso@tuta.io>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Select kmod-backlight as dependency for kmod-drm in case kmod-backlight
is compiled.
This fixes kernel 5.10 build issues on x86-geode with all kmods
enabled:
Package kmod-drm is missing dependencies for the following libraries:
backlight.ko
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_MDIO_OF depends on CONFIG_OF which is not enabled for x86.
Fixes builds of x86 with Kernel 5.10 due to unresolved dependencies.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the name suggests, act_gact has the generic actions such as dropping
and accepting packets, so move it into kmod-sched-core.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The can-dev.ko kernel module was moved in kernel 5.4.110 and 5.10.28.
Fixes: a1311df95587 ("kernel: bump 5.10 to 5.10.28")
Fixes: b0a34e886d ("kernel: bump 5.4 to 5.4.110")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dependency tracking for kmod-sound-hda-core is fragile. Enabling some sound
codecs (Realtek, Conexant, Sigmatel) implicitly adds a kmod-ledtrig-audio
dependency, while an enabled kmod-ledtrig-audio can be picked up through
enabling others (e.g. kmod-sound-hda-intel), and the behaviour can change
across kernel versions.
As kmod-ledtrig-audio is under 2KB, make it an unconditional dependency.
Fixes: a374b8f190 ("kernel: 5.10: update sound modules")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447923636
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update file paths for kmod-sound-hda-intel and reflect new dependency of
kmod-sound-hda-core on kmod-ledtrig-audio.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add conditional dependency on kmod-of-mdio due to mdio_devres.c code:
#if IS_ENABLED(CONFIG_OF_MDIO)
...
EXPORT_SYMBOL(devm_of_mdiobus_register);
#endif /* CONFIG_OF_MDIO */
Fixes: 95a3741d17 ("kernel: support new mdio_devres.ko module in 5.10")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Partially restore the wild-card matching for kmod-usb3 modules to fix
build on platforms without PCI which otherwise file, as seen on
buildbot:
ERROR: module '[...]/linux-5.4.102/drivers/usb/host/xhci-pci.ko' is missing.
modules/usb.mk:1675: recipe for target '[...]/kmod-usb3_5.4.102-1_mips_mips32.ipk' failed
Fixes: 7bda2e9aba ("kernel: fix kmod-usb3 dependencies")
Fixes: be23f9818a ("apm821xx: add support for kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adding CONFIG_USB_XHCI_PCI_RENESAS to KCONFIG made it so it was set
for all targets that included kmod-usb3, not just the intended
apm821xx/nand. xhci-pci has a dependency on xhci-pci-renesas if
CONFIG_USB_XHCI_PCI_RENESAS is set, breaking kmod-usb3 builds on
Linux 5.10 on all other targets.
Rework the dependencies by breaking out xhci-hcd, xhci-mtk, and
xhci-pci-renesas into new hidden kernel modules and setting kmod-usb3
dependencies properly.
Tested by building mt7621 and apm821xx/nand with kmod-usb3 on Linux 5.10
Fixes: be23f981 ("apm821xx: add support for kernel 5.10")
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
CHACHA_MIPS depends on CPU_MIPS32_R2. Therefore,
kmod-crypto-lib-chacha20 should not contain chacha-mips.ko on MIPS32 R1
targets. Enforce that in the target-specific definition.
Fixes bcm47xx, bcm63xx, lantiq/ase, ath25 builds.
Fixes: 06351f1 ("kernel: migrate wireguard into the kernel tree")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Use NETWORK_SUPPORT_MENU like all other modules in netsupport.mk. Drop
SECTION and CATEGORY fields as they are set by default and to match
other packages in netsupport.mk. Use better TITLE for kmod-wireguard
(taken from upstream drivers/net/Kconfig).
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
On Linux 5.4, build WireGuard from backports. Linux 5.10 contains
wireguard in-tree.
Add in-kernel crypto libraries required by WireGuard along with
arch-specific optimizations.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
newer firmware versions. Also the default LED configuration is updated
to use the correct devices.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
CONFIG_THERMAL option was changed to boolean in upstream linux commit
554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's option").
Switch it to 'y' and remove FILES and AUTOLOAD for non-existant module file.
And update the descripton text for the package as in upstream linux commit
eb8504620381 ("thermal: Rephrase the Kconfig text for thermal").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
This patch adds kernel module for Silicon Labs CP2112 HID USB to SMBus
Master Bridge. This is a HID device driver which registers as an i2c
adapter and gpiochip to expose these functions of the CP2112.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Since we're now able to select CONFIG_NET_UDP_TUNNEL at will, drop the fake
dependencies.
This is a partial revert of commit d7e040f8bc
"kernel: add fake users for udptunnel and iptunnel modules".
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Since generic has the option set to y and other targets now inherit that
choice, there is no behaviour change
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
0fdfef9aa7ee68ddd508aef7c98630cfc054f8d6 upstream removed CIFS_SMB311.
Kernels 4.19 and above do not have it. Currently only kernels 4.19 and
5.4 are in the tree.
The Kconfig file in the kernel has more selection that what is in here.
Add the rest and reorder based on upstream ordering.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This add support for USB-to-Ethernet Aquantia AQtion
5/2.5GbE adapters based on the AQC111U controllers.
Run-tested: x86
Adapter-tested: Sabrent NT-SS5G
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Zstd is supported by the crypto API since Linux 4.18. Enable this feature and
reveal the package in the configuration section, so the user can select it.
This allows zstd to be used as a compression algorithm in zram, for example.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
I've just noticed on i.mx6 target, that there are missing kernel symbols
so I'm fixing it.
Fixes: 3c5d70ad26 ("kernel: add module support Solarflare network adapter")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This change adds the configuration option to build and include
the nft_queue kernel module, which allows traffic to be queued up
to userspace from an nftables rule
Tested-by: Sébastien Delafond sdelafond@gmail.com
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
This removes switches dependent on kernel version 4.19 as well as
several packages/modules selected only for that version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 7f94e2afcf.
Package kmod-nft-core is missing dependencies for the following libraries:
nft_reject.ko
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
This option is now activated in the generic kernel configuration, no
need to do it for a specific package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This config option was moved to the generic kernel configuration.
Fixes: ab1bd57656 ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch intruduce SATA support for layerscape devices.
Target specific package with ahci_qoriq driver was added
to local modules.mk.
Kmod package was added to default packages for devices with
SATA interface.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
As the PWM has its own sub-system in the Linux kernel,
I think it should be handled in the same way as GPIO, RTC, PCI...
This patch introduces a specific feature flag "pwm" and the
"leds-pwm" kernel module as the first customer.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
CONFIG_BMP085* is replaced by CONFIG_BMP280 since 4.9[1] and this package is empty.
OpenWRT also has kmod-iio-bmp280* package and we can drop old packages.
1. [ misc: retire the old BMP085 driver ]
(832c8232dd (diff-5000d544d790c669405eb2a6775e5981))
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
TITLE is "NFS4 filesystem client support" (Line 428)
but the description is "Kernel module for NFS v4 support" (Line 438).
Use "Kernel module for NFS v4 client support" on line 438.
Signed-off-by: Bob Cai <1119283622@qq.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes switches dependent on kernel version 4.14 as well as
several packages/modules selected only for that version.
This also removes sched-cake-virtual, which is not required anymore
now that we have only one variant of cake.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target is still on kernel 4.14, and no attempt has been made to
update it to a newer kernel. Since we already are two LTS versions ahead
of that the target is dropped, as the chance of somebody bumping it will
only decrease with time.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.
Do this in this patch and remove the target config entries added
due to this issue.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
47a9f0d service: add method to query available container features
afbaba9 initd: attempt to mount cgroup2
ead60fe jail: use pidns semantics also for timens
759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
83053b6 instance: add instances into unified cgroup hierarchy
16159bb jail: parse OCI cgroups resources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Zram is only strictly dependent on lzo, not lz4. Break this dependency and
make the lz4 module visible in the configuration, in order for the user to
have the choice of enabling/disabling it, if (s)he sees fit.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Quoting part of original message from eefb5f741015 commit in
linux-firmware repository:
This adds the "minifw" version of the EIP197 firmware, which the inside-
secure driver will use as a fallback if the original full-featured
firmware cannot be found. This allows for using the inside-secure driver
and hardware without access to "official" firmware only available under
NDA.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Enable SCSI low-level drivers on targets that don't have it already in
order to fix following build failures on few platforms:
.config:4739:warning: symbol value 'm' invalid for SCSI_LOWLEVEL
* Restart config...
* SCSI low-level drivers
SCSI low-level drivers (SCSI_LOWLEVEL) [Y/n] (NEW) aborted!
Fixes: b88f8202c4 ("kernel: add iscsi-initator support")
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following issue:
Package kmod-iscsi-initiator is missing dependencies for the following libraries:
crypto_hash.ko
Fixes: b88f8202c4 ("kernel: add iscsi-initator support")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Module is needed for using iscsi-initiator userspace applications
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[added missing newline between kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
All devices are using nand images. Built-in MMC/SD modules are not needed
anymore.
Run tested: pogo v4
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add kmod for the ST LSM6DSX IMU driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fixed missing regmap module dependencies]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
This updates the package to contain the kernel object (.ko) file instead
of the plain object (.o) file.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
The combination +@IPV6:kmod-ipsec6 is not valid, the +a:b
syntax implies the @. Fix it.
Fixes: 2e6b6f9fca ("kernel: add @IPv6 dependency to ipv6 modules")
Reported-by: Oldřich Jedlička (@oldium)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 1b973b54ea.
It turns out act_police is included in the kmod-sched package so this
package turns out to be superfluous and causes file provision conflicts.
Ooooops! Best revert it then.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
"Whoop whoop, sound of da police"
Add an ingress capable traffic policer module configurable with tc.
From the man page:
The police action allows to limit bandwidth of traffic matched by the
filter it is attached to. Basically there are two different algorithms
available to measure the packet rate: The first one uses an internal
dual token bucket and is configured using the rate, burst, mtu,
peakrate, overhead and linklayer parameters. The second one uses an
in-kernel sampling mechanism. It can be fine-tuned using the estimator
filter parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
IPv6 modules should all depend on @IPV6, to avoid circular dependencies
problems, especially if they select a module that depends on IPV6 as
well. In theory, if a package A depends on IPV6, any package doing
'select A' (DEPENDS+= A) should also depend on IPV6; otherwise selecting
A will fail. Sometimes the build system is forgiving this, but
eventually, and unexpectedly, it may blow up on some other commit.
Alternatively one can conditionally add IPv6 dependencies only if
CONFIG_IPV6 is selected: (DEPENDS+= +IPV6:package6).
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The mlk5 kmod lacks all necessary build symbols
for kernel 4.14 (again).
Add missing symbols to avoid build failure on these targets.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rewrite commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
Missing config symbols could lead to build failures on kernel
4.14/4.19.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Use in tree version of cake for kernels 4.19+ and backport features from
later kernel versions to 4.19.
Unfortunately PROVIDES dependency handling produces bogus circular
dependency warnings so whilst this package and kmod-sched-cake-oot
should be able to PROVIDE kmod-sched-cake this doesn't work.
Instead, remove the PROVIDES option and modify package sqm-scripts to
depend on the correct module independently.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.
Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors
"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read [...]
using sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0<C2><B0>C (low = +0.0<C2><B0>C, high = +60.0<C2><B0>C)
(crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
(lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."
This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This external switch driver should be loaded on boot for network support
in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Beginning with linux 5.3, kmod-serial-8250 uses functions provided by
serial_mctrl_gpio.ko if GPIO support is enabled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-i2c-mux-pca954x
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-hwmon-* will not get into images unless kmod-hwmon-core is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-gpiofan
- kmod-hwmon-lm63
- kmod-hwmon-lm75
- kmod-hwmon-lm85
- kmod-hwmon-lm90
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, adjust line wrapping]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
By default on module load, 2 ifb interfaces are created and typically
remain unused, cluttering 'ip link' outputs and generally confusing
things. sqm-scripts for example, creates its own ifb interface/s
instead of using these 2 defaults ifbs.
Tell the ifb module to not create any default ifbs on load via the
numifbs parameter.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This was available since kernel 5.4. The one provided in packages feed
will be considered deprecated and renamed to kmod-fs-exfat0.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(use name kmod-fs-exfat. use "@!(LINUX_4_4||LINUX_4_19)" for dependency)
Adds into 4.19 backported kernel module from 5.1 for Sensirion SPS30
particulate matter sensor, for kernel 5.4 backported dependency fix.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Otherwise we would need to enable IIO_TRIGGERED_BUFFER symbol in all
kernels in order to be able to use any of the IIO modules which are
utilizing triggered buffer based data acquisition method.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since now we support both kernel 4.19 and 5.2, change the
condition to remove driver when on kernel 4.14
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fixes following build error on mpc85xx/p2020:
Package kmod-iio-st_accel is missing dependencies for the following libraries:
regmap-core.ko
Fixes: 2d8f4c4fbd ("kernel: iio: add st-accel driver modules")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds kernel modules for various STMicroelectronics accelerometers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch fixes the regression caused by adding the NEON
variant of the ghash as the default ghash package package:
> ERROR: module '[...]/arch/arm/crypto/ghash-arm-ce.ko' is missing.
> modules/crypto.mk:286: recipe for target
> '[...]/kmod-crypto-ghash_4.19.106-1_aarch64_cortex-a53.ipk' failed
This patch limits the scope to the ARM32/cortexa9 target of mvebu.
Fixes: 285df63efc ("kernel: build neon-asm version of ghash module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This builds the regular arm and arm-neon asm optmized modules for sha1
and sha512, for targets that set CONFIG_ARM_CRYPTO.
On ip40xx, the arm-asm version of sha1 improves performance by 5% over
the generic C implementation; sha1-neon is 25% faster than generic,
and sha512-neon, 259%.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This alone improves AES-GCM performance by up to 50% on ipq40xx. This
is enabled for targets that support neon and set CONFIG_ARM_CRYPTO:
imx6, ipq40xx, and mvebu.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The nvmem framework is now used in net/ethernet/eth.c and the nvmem
sysfs is split into a separate Kconfig option. More work would be needed
to adapt this patch for the broader use. The current patch compiles fine
on ath79, but it breaks the x86 target.
nvmem is also compiled into the kernel for most of our targets for
example ath79 anyway, so patching the kernel to remove it is now harder
and not the case on multiple targets anyway. Instead of making this work
on kernel 5.4 just remove this hack patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module was added with kernel 4.15, but is was removed again with
kernel version 5.3. OpenWrt does not support specifying a kernel version
range so just break it with kernel 4.14 and only support recent kernel
versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With kernel 5.4 kmod-sound-hda-intel also needs snd-intel-nhlt.ko, but
this kernel module is only build on x86, make the OpenWrt kmod depend on
TARGET_x86.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gigaset was moved to staging in kernel 5.4, just deactivate it on
recent kernel versions instead of adapting it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 5.3 and 5.4 some crypto modules were split into two modules,
one implementing the crypto algorithm and the other integrating it
into the Linux crypto framework.
Adapt OpenWrt to support this split.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the new xfrm4_mode_beet, xfrm4_mode_transport,
xfrm4_mode_tunnel and their IPv6 versions on kernel 5.4. These modules
were newly added in kernel 5.2.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Packages kmod-bluetooth_6lowpan and kmod-ieee802154_6lowpan contain an
underscore in the package name. This causes problems in package/install
because when building a list of package files to install offline using
opkg, it uses a wildcard of the form $(dir)/$(pkg)_*.ipk.
If you were to select kmod-bluetooth=y, but kmod-bluetooth_6lowpan=m,
the latter would be picked up by that wildcard, and make package/install
would fail:
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies
* for kmod-bluetooth_6lowpan:
* kmod-6lowpan
* opkg_install_cmd: Cannot install package kmod-bluetooth_6lowpan.
Changing the wildcard pattern is not trivial, and there may be other
places in the build system making this assumption about the package name
format.
Using a dash in place of the underscore avoids the issue.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Package kernel module for Linear Technology MCP3021/3221 I2C connected
current and voltage monitor chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is generally more desirable to use older kernel versions for
dependencies, as this will require less changes when newer kernels
are added (they will by default select the newer packages).
Since we currently only have two kernels (4.14 and 4.19) in master,
this patch applies this logic by converting all LINUX_4_19 symbols
to their inverted LINUX_4_14 equivalents.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for Methode DM7052 NBASE-T module to OpenWRT. These
patches are taken from my "phy" branch, and will be sent for the
next kernel merge window.
Signed-off-by: Russell King <linux@armlinux.org.uk>
[jonas.gorski: move patches to pending, refresh patches]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
After kernel 4.9 has been removed, this removes all (now obsolete)
kernel version switches that deal with versions before 4.14.
Package kmod-crypto-iv is empty now and thus removed entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- usb-dwc3-of-simple is not used anymore as we have qcom dedicated driver
- usb-phy-qcom-dwc3 is not dependent of dwc3-of-simple
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AutoLoad parameter must match the exact kernel module name. Fix it.
Fixes: 125f1ce9ad ("kernel: video: add DRM core and IMX DRM support for HDMI/LVDS")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This is needed to export crypto information to netfilter, allowing
the alt. afalg openssl engine to obtain information about the drivers
being used.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The kconfig symbol is an invisible one since its introduction. It is
not supposed to be enabled on its own.
Resolves FS#1821
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This driver supports the Bosch Sensortec BME680 gas, humidity, pressure
and temperature sensor.
Tested I2C and SPI modes on a Raspberry Pi Zero W.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
crypto-arc4 move into a module with commit c3a78955f3,
fs-nfs-common-rpcsec compile error without arc4 support.
Ref: https://github.com/openwrt/packages/issues/9912
Fixes: c3a78955f3 ("kernel: move crypto-arc4 into a module")
Signed-off-by: Ruixi Zhou <zhouruixi@gmail.com>
Add missing dependencies to i2c-core and regmap-spi. These get activated
when these modules are build in this driver, which is the case when we
build all modules. This fixes the build on some targets. This was found
by the buildbot.
Fixes: 34e2526f9f ("kernel: add kmod-rtc-pcf2127")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
add module to support Emulex OneConnect
common in 10Gbit SFP+ cards by Dell/HP/IBM
supports OneConnect OCe10xxx OCe11xxx OCe14xxx,
LightPulse LPe12xxx
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This is already enabled as kernel built-in feature in mvebu target and
none other target will use it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
