Contrary to common ipTIME NOR devices, the "Config" partition of T5004
and AX2004M contain normal U-Boot environment variables. Renaming the
partition into "u-boot-env" serves for better description, and it also
conforms to common naming practice in OpenWrt.
This patch might also be extended to A3004T, but its u-boot-env
partition layout has not been confirmed yet.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7 ("kernel: add support for mediatek NMBM flash mapping support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some MT7915 calibration data consists of two parts. The first part
"eeprom" size is 0xe00. The second part "precal" size is 0x19c10.
Though some devices may not have precal data, it's better to assume
that precal data exists as no users/developers confirm it. On the
other hand, some devices definitely do not contain precal data
because the EEPROM partition size is smaller than the precal NVMEM
cell size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.
P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.
This partially reverts commit 9ac891f8c4.
Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.
The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:
mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1
The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.
mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.
Tested on a range of devices documented on the GitHub PR.
Link: https://github.com/openwrt/openwrt/pull/10238
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.
Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
* MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
* Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
* Pinout: [3V3] (TXD) (RXD) (GND)
MAC addresses:
| interface | MAC address | source | comment
|-----------|-------------------|----------------|---------
| LAN | 58:xx:xx:00:xx:9B | | [1]
| WAN | 58:xx:xx:00:xx:99 | |
| WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4 |
| WLAN 5G | 5A:xx:xx:40:xx:98 | |
| | 58:xx:xx:00:xx:98 | config ethaddr |
[1] Used in this patch as WLAN 5G MAC address with the local bit set
Load addresses:
* stock
* 0x80010000: FIT image
* 0x81001000: kernel image -> entry
* OpenWrt
* 0x80010000: FIT image
* 0x82000000: uncompressed kernel+relocate image
* 0x80001000: relocated kernel image -> entry
Notes:
* This device has a dual-boot partition scheme, but this firmware works
only on boot partition 1. The stock web interface will flash only on the
inactive boot partition, but the recovery web page will always flash on
boot partition 1.
Installation via recovery mode:
1. Press reset button, power up the device, wait >10s for CPU LED
to stop blinking.
2. Upload recovery image through the recovery web page at 192.168.0.1.
Revert to stock firmware:
1. Install stock image via recovery mode.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x840000e4
Data Size: 10750165 Bytes = 10.3 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x82000000
Entry Point: 0x82000000
Normally, it should look like this:
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: MIPS OpenWrt Linux-5.10.92
Type: Kernel Image
Compression: lzma compressed
Data Start: 0xbfca00e4
Data Size: 2652547 Bytes = 2.5 MiB
Architecture: MIPS
OS: Linux
Load Address: 0x80001000
Entry Point: 0x80001000
Revert the commit to avoid more people soft-bricking their devices.
This reverts commit f4a79148f8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
