Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some MT7915 calibration data consists of two parts. The first part
"eeprom" size is 0xe00. The second part "precal" size is 0x19c10.
Though some devices may not have precal data, it's better to assume
that precal data exists as no users/developers confirm it. On the
other hand, some devices definitely do not contain precal data
because the EEPROM partition size is smaller than the precal NVMEM
cell size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
I-O DATA WN-DEAX1800GR uses MT7915 PCIe NIC. The correct EEPROM
size is 0xe00.
Fixes: ac68fbf526 ("ramips: add support for I-O DATA WN-DEAX1800GR")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
I-O DATA WN-DEAX1800GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash : RAW NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (MediaTek MT7915)
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MT7530 (SoC)
- LEDs/Keys : 6x/3x
- UART : through-hole on PCB (J2)
- assignment: 3.3V, GND, TX, RX from "1" marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WN-DEAX1800GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button to perform firmware update
4. On the initramfs image, perform sysupgrade with the
squashfs-sysupgrade.bin image
5. Wait ~120 seconds to complete flashing
Note:
- This device has 2x OS images on the flash storage. In this support,
the first one will be used.
Warning:
- Do not use "saveenv" command on U-Boot CLI.
This device has wrong u-boot-env data. The actual length of individual
env data installed to the device is 0x1000 (4 KiB), but installed
U-Boot requires 0x20000 (128 KiB). So U-Boot determines the data is
invalid. Then, if you perform saving environment data with saveenv on
U-Boot CLI, installed env data will be overwritten with too few
default values without individual values (SSID, password, MAC
addresses, etc...).
MAC addresses:
LAN : 50:41:B9:xx:xx:F4 (Config, ethaddr (text))
WAN : 50:41:B9:xx:xx:F6 (Config, wanaddr (text))
2.4 GHz: 50:41:B9:xx:xx:F4 (Config, rmac (text) / Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:F5 (none)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
