current preinit code in base-files doesn't config switch when there are
no port roles defined. But this kind of configuration exists on single
port devices where switch vlan is simply disabled.
configure reset and enable_vlan property when a switch node exist.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The file /lib/functions/system.sh depends on find_mtd_index() and
find_mtd_part() located in /lib/function.sh, so let's source that
file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The default_postinst() function in /lib/functions.sh sources
/lib/functions/system.sh before cycling through uci-defaults files.
This creates a pseudo-cyclic dependency as system.sh also uses
functions that are located in functions.sh. Despite that, there
is actually only one uci-defaults file in the entire repo that needs
system.sh, and this one contains an explicit source for system.sh
anyway.
Consequently, this patch removes the sourcing of system.sh in
functions.sh. There are no relevant uses in packages, routing and
luci repositories.
This may require adjustments for downstream, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Because /etc/profile (and ~/.profile) are read by login shells only,
aliases and functions defined there are not available to non-login
shells, e.g. when using screen or tmux.
If the ENV environment variable exists (exported by /etc/profile or
~/.profile) and references an existing file, then all interactive shells
(login or non-login) will read that file as well.
This sets the ENV environment variable in /etc/profile, pointing to
/etc/shinit.
This also adds /etc/shinit, which:
* Contains alias and function definitions originally in /etc/profile
* Sources /etc/mkshrc if the user is using mksh (also originally in
/etc/profile), as /etc/mkshrc is meant for all interactive shells
* Sources ~/.mkshrc if the user is using mksh, to compensate for the
fact that mksh will not read ~/.mkshrc if ENV is set
* Sources ~/.shinit if the user is not using mksh
This also removes the shebang from /etc/profile, as the file is sourced,
not executed.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
For devices without a dedicated 'diag' LED, we use sometimes one of
other LEDs for indicating at least 'boot', 'failsafe' and 'upgrade'
stages. In some cases, at the same time these LEDs have defined default
triggers in DTS using 'linux,default-trigger' property. Current 'diag'
setup removes the trigger and turns off 'boot' LED after bootup.
One of the examples of such device is TP-Link TL-WR841N v14 (ramips)
which uses 'wlan' LED with defined 'linux,default-trigger' for 'diag':
aliases {
led-boot = &led_wlan;
led-failsafe = &led_wlan;
led-upgrade = &led_wlan;
};
[...]
led_wlan: wlan {
label = "tl-wr841n-v14:green:wlan";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
This patch extends 'diag.sh' and 'leds.sh' scripts to make sure default
trigger defined in DTS is restored for 'diag' LED which isn't used for
indicating 'running' stage.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is
not fully compatible we drop its usage.
Also change to "=" for simple test, which is sufficient. (see d6ac8ca76c)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[split patch, removed shebang]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It's cleaner and faster as it does not need to do extra work.
Also removed $() to avoid executing the output. The shell can handle it.
https://github.com/koalaman/shellcheck/wiki/SC2143
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[correct || to && for one conversion]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Failsafe code of dropbear should be in the dropbear package not the
base-files package.
Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me>
With this change the well known jshn library will be used, to build the
json arguments for the ubus sysupgrade method. This is also used in all
other shell program that uses JSON. This commit unifies that.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The preinit network initialisation and failsafe informational message
are inherently racy as the interface takes some time to become
functional after "ip link set $pi_ifname up" command.
Consider this timing:
[ 12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 12.118877] random: procd: uninitialized urandom read (4 bytes read)
[ 13.068614] eth1: link up (1000Mbps/Full duplex)
[ 13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
Since the UDP message was sent prior to link becoming ready, it was
never seen on the wire.
The default failsafe timeout is set to 2 seconds, so with this patch
there are two attempts to send the message, one spent in vain, and the
other visible in tcpdump on an attached host. Of course, in cases when
the interface is brought up faster it leads to two messages, however it
should be harmless. This patch (almost) doesn't affect normal boot time
while still allowing to enter failsafe reliably with a single button
press, matching the official "generic failsafe" documentation.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:
ucidef_set_interface_lan "eth0 eth1.1"
ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01"
will return
config device 'lan_eth0_dev'
option name 'eth0'
option macaddr 'yy:yy:yy:yy:yy:01'
config device 'lan_eth1_1_dev'
option name 'eth1.1'
option macaddr 'yy:yy:yy:yy:yy:01'
ref: https://github.com/openwrt/openwrt/pull/2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit ed5b9129d7 ("base-files: implement generic service_running")
has added EXTRA_HELP variable, thus overriding already available
EXTRA_HELP text available in other init scripts, resulting in the
missing help text from services like dropbear for example.
So fix this regression by appending EXTRA_HELP text provided by the
other init scripts into the one provided by the script itself.
Fixes: ed5b9129d7 ("base-files: implement generic service_running")
Signed-off-by: Peter Stadler <peter.stadler@student.uibk.ac.at>
[commit title/description facelift, fixes tag, fixed From:, pkg bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Discovered recent changes had broken sysupgrade for ar71xx mikrotik
rb-493g, traced the problem to missing /usr/share/libubox/jshn.sh after
switching to tmpfs.
Signed-off-by: Russell Senior <russell@personaltelco.net>
uci-defaults are sourced and non-executable, so they do not require
a shebang.
While at it, apply consistent naming scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that netifd and hostapd allow dynamic reconfiguration, add a
command to trigger it.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 6170c46b47.
There has been demand for further evaluation of the impact of a
changed hostname, so this is reverted for now. The default hostname
will be "OpenWrt" again after this commit.
The macaddr_geteui() function is not removed by this revert.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If a label MAC address is provided for device, system
will rename the hostname with OpenWrt_{eui mac address}.
This helps to distinguish between different devices.
Since it's no good idea to nest json_* functions, this code does
not use get_mac_label directly, but only get_mac_label_dt as
external resource.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
[merged with commit introducing macaddr_geteui, rebased on updated
label MAC address storage, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If set, label MAC address is available from one of two sources,
device tree or board.json. So far, the function get_mac_label
was meant for retrieving the address, while an option in uci
system config was specified only for case 2 (board.json).
The uci config option has several drawbacks:
- it is only used for a fraction of devices (those not in DT)
- label MAC address is a device property, while config implies
user interaction
- label_macaddr option will only be set if /etc/config/system
does not exist (i.e. only for new installations)
Thus, this patch changes the behavior of get_mac_label:
Instead of writing the value in board.json to uci system config
and reading from this location afterwards, get_mac_label now
extracts data from board.json directly. The uci config option
won't be used anymore.
In addition, two utility functions for extraction only from DT
or from board.json are introduced.
Since this is only changing the access to the label MAC address, it
won't interfere with the addresses stored in the code base so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"block mount" invokes "hotplug-call mount". It emits the following
error when mount is not present
hotplug-call call failed
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Moving a file between tmpfs and other fs is neither
faster nor safer, thus no point in doing it in two steps.
Use new jshn option to write output directly to file.
Originally discussed here:
http://lists.openwrt.org/pipermail/openwrt-devel/2017-December/010127.html
Signed-off-by: Roman Yeryomin <roman@advem.lv>
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"coreutil-date" package from the packages feed replaces the Busybox date
applet by symlinking /usr/bin/gnu-date to /bin/date. This prevents the system
init script from setting kernel timezone because the GNU date utility does not
provide such functionality:
root@OpenWrt:~# date -k
date: invalid option -- 'k'
Try 'date --help' for more information.
A specific reference to the Busybox date applet prevents alternative date
utilities from breaking the system init script.
Signed-off-by: Val Kulkov <val.kulkov@gmail.com>
The factory uboot of the Turris Omnia boots with "root=b301", and we
instruct new users to sysupgrade from there (e.g. method 1, step 7).
Currently, this will fail with "Unable to determine upgrade device".
Add a new case to export_bootdevice, which parses the hex argument.
Fixes commit 2e5a0b81 ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
For many devices, MAC addresses cannot be retrieved via the
device tree alias.
To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.
This is based on the work of Rosy Song <rosysong@rosinson.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
To refer to the MAC address on a device's label, one can
specify the alias label-mac-device in the DTS which should
point to the bearer of the corresponding MAC address.
With the function get_mac_label, the user can retrieve then
retrieve this address and use it as a value that uniquely
identifies his device.
This is severely helpful for several downstream functionalities,
e.g. define MAC addresses of custom netifs or change the SSID to
be easily recognizable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adds a default status action for init.d scripts.
procd "service status" will return:
0) for loaded services (even if disabled by conf or dead)
3) for inactive services
4) when filtering a non-existing instance
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[rebased, cleaned up]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This explicitly tells procd what backup file should be used during
sysupgrade (if any). It's much more generic this way compared to the
magic /tmp/sysupgrade.tgz file that had to be created before a call.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This allows platform code to check if firmware image can be used with
preserving a backup. It may be used e.g. when installing vendor
firmwares that won't restore appended backup archive.
Suggested-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The actual retrieval of the MAC address in mtd_get_mac_binary_ubi()
is the same as in get_mac_binary(). Thus, use the latter function
in the former to reduce duplicate code.
This will also allow to benefit from the enhanced path check there
and bring mtd_get_mac_binary_ubi() more in line with the similar
mtd_get_mac_binary().
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mtd_get_mac_text helper method did not support hexadecimal offset
values, resulting them to break after 75bfc393ba ("treewide:
convert MAC address location offsets to hexadecimal")
This commit fixes this by evaluating the hexadecimal input,
converting them to decimal.
Signed-off-by: David Bauer <mail@david-bauer.net>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
