Commit Graph

7 Commits

Author SHA1 Message Date
Hauke Mehrtens
0dc4ab344b sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmware
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.

Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-12-27 00:58:29 +01:00
Chukun Pan
fde68cb809 sunxi: add support for FriendlyARM NanoPi R1S H5
Specification:
  CPU: Allwinner H5, Quad-core Cortex-A53
  DDR3 RAM: 512MB
  Network: 10/100/1000M Ethernet x 2
  USB Host: Type-A x 1
  MicroSD Slot x 1
  MicroUSB: for power input
  Debug Serial Port: 3Pin pin-header
  LED: WAN, LAN, SYS
  KEY: Reset
  Power Supply: DC 5V/2A

Installation:
  Write the image to SD Card with dd.

Note:
  1. OpenWrt currently does not support LED_FUNCTION, change back to the
     previous practice (Consistent with NanoPi R1).
  2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
     ("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
     change the phy-mode from rgmii to rgmii-id.
     So set phy-mode for 5.4 and 5.10 respectively.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-10-30 21:17:20 +02:00
Zoltan HERPAI
3225241c2b sunxi: add support for H6 boards and OrangePiOnePlus
Specifications:

SoC	Allwinner H6 @ 1.8 Ghz
DRAM	1Gb LPDDR3
Power	DC 5V @ 3A
Video	HDMI (Type 2.0A - full)
Audio	HDMI, on-board microphone
Network	10/100/1000Mbps Ethernet (Realtek RTL8211)
Storage	microSD
USB	1 USB2.0 Host, 1 USB2.0 OTG
Debug	Serial UART

Flashing instructions:
 Standard sunxi SD card installation procedure - copy image to SD card,
 insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-11 23:14:55 +02:00
Zoltan HERPAI
bb9915407b sunxi: enable wifi module on Pine64 boards
The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi
module, carrying an RTL8723BS. The wifi part is connected via
SDIO, the BT part is connected via UART. The BT part requires
additional code changes in the drivers so we'll skip that until 5.10.
Aside from a DTS patch to enable the wifi module, add the required
packages into the device definitions.

[    8.996970] RTL8723BS: module init start
[    9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[    9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[    9.014785] pnetdev = 000000009bdd5000
[    9.047780] RTL8723BS: rtw_ndev_init(wlan0)
[    9.053349] RTL8723BS: module init ret =0

root@OpenWrt:/# iw list
Wiphy phy0
        wiphy index: 0
        max # scan SSIDs: 9
        max scan IEs length: 2304 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Available Antennas: TX 0 RX 0
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * monitor
        Band 1:
                Frequencies:
                        * 2412 MHz [1] (20.0 dBm)
                        * 2417 MHz [2] (20.0 dBm)
                        * 2422 MHz [3] (20.0 dBm)
                        * 2427 MHz [4] (20.0 dBm)
                        * 2432 MHz [5] (20.0 dBm)
                        * 2437 MHz [6] (20.0 dBm)
                        * 2442 MHz [7] (20.0 dBm)
                        * 2447 MHz [8] (20.0 dBm)
                        * 2452 MHz [9] (20.0 dBm)
                        * 2457 MHz [10] (20.0 dBm)
                        * 2462 MHz [11] (20.0 dBm)
                        * 2467 MHz [12] (20.0 dBm) (no IR)
                        * 2472 MHz [13] (20.0 dBm) (no IR)
                        * 2484 MHz [14] (20.0 dBm) (no IR)

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-03-29 21:44:34 +02:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
Roman Kuzmitskii
02e8182d87 sunxi: add support for Libre Computer ALL-H3-CC H5
Specification:

- CPU: Allwinner H5, Quad-core Cortex-A53 Up to 1GHz
- DDR3 RAM: 2GB
- Network:
    10/100M Ethernet x 1
- IR: x1 (Receive)
- USB (Host) Type-A x3
- USB (OTG) Type-A x1
- MicroSD Slot x 1
- eMMC Slot x1
- MicroUSB power input
- GPIO 40pin header
- UART 3pin header
- Leds:
    - librecomputer:blue:status
    - librecomputer:green:pwr
- Buttons:
    - uboot button (used to enter fel mode)
    - power button (can trigger power on)
- Power Supply via MicroUSB or GPIO 5V/2A

Installation:

- Write the image to SD Card with dd
- Boot from the SD Card

Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
[Fixed Signed-off-by]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-11-12 18:21:17 +01:00
Adrian Schmutzler
bb39fea11a treewide: simplify inclusion of subtarget image files
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.

This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.

For sunxi, this includes a trivial rename of the subtarget image
Makefiles.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00