Most (all?) of the realtek devices have two u-boot config partitions
with a different set of variables in each. The U-Boot shell provides
two sets of apps to manipulate these:
printenv- print environment variables
printsys- printsys - print system information variables
saveenv - save environment variables to persistent storage
savesys - savesys - save system information variables to persistent storage
setenv - set environment variables
setsys - setsys - set system information variables
Add support for multiple ubootenv configuration types, allowing
more than one configuration file.
Section names are not suitable for naming the different
configurations since each file can be the result of multiple sections
in case of backup partitions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
